Kenmore 4102 Installation Instructions - Page 3

To avoid, breakage, Do NOT handle - slide in

Get Kenmore 4102 - Elite 30 in. Slide-In Electric Range PDF manuals and user guides View all Kenmore 4102 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

To avoid breakage: Do NOT handle or manipulate the unit by the cooktop glass. The counter-top around the cut-out should be flat and leveled (see hatched area on illustration 1). Before installing the unit, measure the heights of the two (2) cabinet sides (H1-4), front and back (see illustration 1) from the floor to the top of the counter. Level the range using the four (4)leveling legs so that the height from the floor to the underside of the cooktop glass frame Shave Raised 1 Y2" Max. 1 (3.8 cm Max.) I Edge to Clear Space for a 31Y2" (81 cm) Wide is greater than the tallest Cooktop. cabinet measurement by at least 1/1 6" (see illustration 2). Illustration 1 Slide the unit into the cabinet. Make sure the center of the unit is aligned with the center of the cabinet cut-out. Remove the protective channels on each side of the glass cooktop (if provided). The metal flange under each side of the cooktop MUST be placed over the cabinet countertop for proper unit support. The glass cooktop should NOT directly touch the countertop (see illustration 2) or could cause glass breakage voiding the warranty. Level the unit if needed. After the installation, MAKE SURE that the uni is supported by the leveling legs NOT by the cooktop. ..:to successfullyinstall the range, the initial level height from floor to underside of cooktop glass frame should be at least 1/16" taller than cabinet sidesas measured in step 1. Illustration 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
To avoid
breakage:
Do NOT handle
or
manipulate
the
unit
by the
cooktop
glass.
The counter-top
around
the cut-out
should
be flat
and
leveled (see hatched
area on illustration
1).
Before installing
the unit,
measure
the heights
of the two
(2)
cabinet
sides (H1-4), front
and back (see illustration
1) from the
floor to the top of the counter.
Level the range using the
four
(4)leveling
legs
so
that the height
from
the
floor to the underside of
the cooktop
glass frame
is greater
than the tallest
cabinet
measurement
by
at least 1/1 6"
(see
illustration
2).
Shave
1
Y2"
Max.
1
(3.8 cm Max.)
I
Raised
Edge
to
Clear
Space for a
31Y2" (81 cm) Wide
Cooktop.
Illustration
1
Slide the unit into the cabinet.
Make sure the center of the unit
is
aligned with
the center
of the cabinet
cut-out.
Remove the protective
channels
on each side of the glass
cooktop
(if provided).
The metal flange
under each side of the cooktop
MUST be
placed over the cabinet countertop
for proper
unit support.
The glass cooktop
should
NOT directly
touch
the countertop
(see illustration
2) or could cause glass breakage
voiding
the
warranty.
Level the unit
if needed.
After
the installation,
MAKE SURE that the uni
is supported
by the leveling legs NOT by the
cooktop.
..:to
successfullyinstall
the
range, the initial
level height from floor
to underside of
cooktop glass frame
should be at least
1/16" taller than
cabinet sidesas
measured in step 1.
Illustration
2