Kenwood DNX573S Quick Start Guide - Page 24

Installing the unit, Installation procedure, Non-Japanese cars DNX893S, DNX7160BTS, DNX693S - wiring harness

Get Kenwood DNX573S PDF manuals and user guides View all Kenwood DNX573S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Installation ÑÑInstallation procedure ÑÑJapanese cars 1) To prevent a short circuit, remove the key from the ignition 7 or 8 5 and disconnect the ¤ terminal of the battery. Car Bracket 2) Make the proper input and output wire connections for each unit. 3) Connect the speaker wires of the wiring harness. 4) Connect the wiring harness wires in the following order; ground, battery, ignition. 5) Connect the wiring harness connector to the unit. 6) Install the unit in your car. 7) Reconnect the ¤ terminal of the battery. 8) Perform the Initial Setup. See Initial settings (P.5). 7 or 8 ✎✎NOTE • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may Cut out to meet the shape of the opening in the vehicle. ⿠⿠Toyota/Scion cars (DNX893S) 1) Cut out accessory 5 as illustrated. Installing the unit skip). ÑÑTrim plate (DNX893S, DNX7160BTS, DNX693S, Cutting line ÑÑNon-Japanese cars (DNX893S, DNX7160BTS, DNX5160BTS) DNX693S, DNX5160BTS) 1) Attach accessory 9 to the unit. 5 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 9 ⿠⿠General Motors cars (DNX893S) 1) Cut out accessory 5 to meet the shape of the opening of the center console. 2) Attach accessory 5 to the unit. 2) Fold double-sided adhesive (accessory 6) along the slit and attach it to accessory 5 cut-out against the center rib as illustrated. Use 2 pieces of accessory 6 for 1 accessory 5 cut-out. 3) Attach accessory 5 cut-out to the unit. 6 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
24
Installation
Ñ
Installation procedure
1) To prevent a short circuit, remove the key from the ignition
and disconnect the
¤
terminal of the battery.
2) Make the proper input and output wire connections for
each unit.
3) Connect the speaker wires of the wiring harness.
4) Connect the wiring harness wires in the following order;
ground, battery, ignition.
5) Connect the wiring harness connector to the unit.
6) Install the unit in your car.
7) Reconnect the
¤
terminal of the battery.
8) Perform the Initial Setup. See
Initial settings (P.5)
.
Installing the unit
Ñ
Non-Japanese cars (DNX893S, DNX7160BTS,
DNX693S, DNX5160BTS)
Bend the tabs of the
mounting sleeve with
a screwdriver or similar
utensil and attach it in
place.
Ñ
Japanese cars
7
or
8
7
or
8
Car Bracket
✎
NOTE
• Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (eg, the sound may
skip).
Ñ
Trim plate (DNX893S, DNX7160BTS, DNX693S,
DNX5160BTS)
1) Attach accessory
9
to the unit.
9
⿠
General Motors cars (DNX893S)
1) Cut out accessory
5
to meet the shape of the opening
of the center console.
2) Attach accessory
5
to the unit.
5
Cut out to meet the shape
of the opening in the
vehicle.
⿠
Toyota/Scion cars (DNX893S)
1) Cut out accessory
5
as illustrated.
Cutting line
5
2) Fold double-sided adhesive (accessory
6
) along the
slit and attach it to accessory
5
cut-out against the
center rib as illustrated. Use 2 pieces of accessory
6
for
1 accessory
5
cut-out.
3) Attach accessory
5
cut-out to the unit.
6