Kenwood KDC-X993 Instruction Manual - Page 30

DTA Digital Time Alignment setting, X'Over setting

Get Kenwood KDC-X993 - eXcelon Radio / CD PDF manuals and user guides
UPC - 019048183248
View all Kenwood KDC-X993 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Sound Setup DTA (Digital Time Alignment) setting Adjusting fine tuning of the speaker position compensation value specified at (page 29). 1 Enter DTA setting mode Select "SOUND" > "Setup" > "DTA". For how to select Function Control item, refer to (page 6). 2 Select the speaker you want to set Setting speaker Front speaker Rear speaker Subwoofer Display "Front" "Rear" "SW" Turn the Control knob. 3 Set the compensation value of the speaker position Turn the Control knob and push the center when the desired value is displayed. Adjust between 0 and 14.44 feet. Refer to "DTA" of (page 48) on how to set the compensation value. Exit DTA setting mode. X'Over setting Fine adjusting the following setting values corresponding to the X'Over values set in the section (page 29); Adjustment Item Display Front High Pass Filter, "FC" Rear High Pass Filter Front High Pass Slope, "SLOPE" Rear High Pass Slope, Subwoofer Slope * Subwoofer Low Pass "FC" Filter Subwoofer Phase "PHASE" Range Through, 30*, 40, 50*, 60, 70, 80, 90*, 100, 120, 150, 180, 220, 250* (Hz) -6, -12, -18, -24 dB/Oct 30*, 40, 50*, 60, 70, 80, 90*, 100, 120, 150, 180, 220, 250*, Through (Hz) Reverse (180°)/ Normal (0°) *Function of the KDC-X993/ KDC-X693. 1 Enter X'Over setting mode Select "SOUND" > "Setup" > "X'Over". For how to select Function Control item, refer to (page 6). 2 Select the speaker you want to set Setting speaker Front speaker Rear speaker Subwoofer Display "Front" "Rear" "Subwoofer" Turn the Control knob and push the center when the desired item is displayed. 3 Select the item you want to set Item "Front" >"FC" >"SLOPE" "Rear" >"FC" >"SLOPE" "Subwoofer" >"FC" >"SLOPE" >"PHASE" Setting overview Front High Pass Filter Front High Pass Slope Rear High Pass Filter Rear High Pass Slope Subwoofer Low Pass Filter Subwoofer Slope Subwoofer Phase Push the Control knob towards up or down. 4 Set the X'Over value Turn the Control knob. 5 Repeat steps 2 to 4 to complete the X'Over setting. 6 Exit X'Over setting mode Press the [FNC] button. 30 | KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
30
|
KDC-X993/ KDC-HD942U/ KDC-X693/ KDC-MP642U
DTA (Digital Time Alignment) setting
Adjusting fine tuning of the speaker position
compensation value specified at <Cabin selection>
(page 29).
1
Enter DTA setting mode
Select “SOUND”
>
“Setup”
>
“DTA”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2
Select the speaker you want to set
Setting speaker
Display
Front speaker
“Front”
Rear speaker
“Rear"
Subwoofer
“SW"
Turn the Control knob.
3
Set the compensation value of the speaker
position
Turn the Control knob and push the center
when the desired value is displayed.
Adjust between 0 and 14.44 feet.
Refer to “DTA” of <Menu Glossary> (page 48) on
how to set the compensation value.
Exit DTA setting mode.
Sound Setup
X’Over setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <Speaker Setting> (page 29);
Adjustment Item
Display
Range
Front High Pass Filter,
Rear High Pass Filter
“FC”
Through, 30*, 40, 50*, 60, 70,
80, 90*, 100, 120, 150, 180,
220, 250* (Hz)
Front High Pass Slope,
Rear High Pass Slope,
Subwoofer Slope *
“SLOPE”
-6,
-12, -18, -24 dB/Oct
Subwoofer Low Pass
Filter
“FC”
30*, 40, 50*, 60, 70, 80, 90*,
100, 120, 150, 180, 220,
250*, Through (Hz)
Subwoofer Phase
“PHASE”
Reverse (180°)/ Normal (0°)
*Function of the KDC-X993/ KDC-X693.
1
Enter X’Over setting mode
Select “SOUND”
>
“Setup”
>
“X’Over”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2
Select the speaker you want to set
Setting speaker
Display
Front speaker
“Front”
Rear speaker
“Rear"
Subwoofer
“Subwoofer"
Turn the Control knob and push the center
when the desired item is displayed.
3
Select the item you want to set
Item
Setting overview
“Front”
>
“FC”
>
“SLOPE”
Front High Pass Filter
Front High Pass Slope
“Rear"
>
“FC”
>
“SLOPE”
Rear High Pass Filter
Rear High Pass Slope
“Subwoofer"
>
“FC”
>
“SLOPE”
>
“PHASE”
Subwoofer Low Pass Filter
Subwoofer Slope
Subwoofer Phase
Push the Control knob towards up or down.
4
Set the X’Over value
Turn the Control knob.
5
Repeat steps 2 to 4 to complete the X’Over
setting.
6
Exit X’Over setting mode
Press the [FNC] button.