Kenwood NX-320 Operation Manual - Page 15

Installing The Antenna

Get Kenwood NX-320 PDF manuals and user guides View all Kenwood NX-320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Note: ◆ If you do not plan to use the transceiver for a long period, remove the batteries from the battery case. ◆ This battery case has been designed for transmitting at a power of approximately 1 W (the low power setting on your transceiver). If you want to transmit a stronger signal (using the high power setting on your transceiver), use an optional rechargeable battery pack. 1 To open the battery case, press on the two tabs on the upper rear of the case, then pull the two halves apart. 2 Insert 6 AA (LR6) Alkaline batteries into the battery case. • Be sure to match the polarities with those marked in the bottom of the battery case. 3 Align the tabs of the cover with the base, then push down on the cover until it locks in place. INSTALLING THE ANTENNA Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
3
Note:
◆
If you do not plan to use the transceiver for a long period,
remove the batteries from the battery case.
◆
This battery case has been designed for transmitting at a
power of approximately 1 W (the low power setting on your
transceiver).
If you want to transmit a stronger signal (using
the high power setting on your transceiver), use an optional
rechargeable battery pack.
1
To open the battery case, press
on the two tabs on the upper
rear of the case, then pull the
two halves apart.
2
Insert 6 AA (LR6) Alkaline
batteries into the battery case.
•
Be sure to match the polarities
with those marked in the bottom
of the battery case.
3
Align the tabs of the cover with
the base, then push down on
the cover until it locks in place.
INSTALLING THE ANTENNA
Screw the antenna into the
connector on the top of the
transceiver by holding the antenna
at its base and turning
it clockwise until secure.