Kenwood NX-320 Operation Manual - Page 30

STATUS MESSAGE TYPES I AND II ONLY, Transmitting, Receiving

Get Kenwood NX-320 PDF manuals and user guides View all Kenwood NX-320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

STATUS MESSAGE (TYPES I AND II ONLY) You can send and receive 2-digit Status messages which may be decided in your talk group. Messages can contain up to 16 alphanumeric characters. Status messages range from 10 to 99 (80 ~ 99 are reserved for special messages). A maximum of 15 received messages (combined status messages and short messages) can be stored in the stack memory of your transceiver. ■ Transmitting 1 Select your desired zone and channel. 2 Press the key programmed as [Status] to enter Status mode (proceed to step 5) or [Selcall + Status] to enter Selcall mode (proceed to step 3). 3 Press the key to select the station you want to call. • If Manual Dialing is enabled, you can enter a station ID by using the DTMF keypad, or by using the Selector. When using the Selector, cycle through the digits to select a digit, then press the S key to set the digit and move the cursor to the right. Repeat this process until the entire ID is entered. 4 Press the S or key to enter Status mode. 5 Press the key to select the status you want to transmit. • If Manual Dialing is enabled, you can enter a status ID by using the DTMF keypad, or by using the Selector (refer to step 3, above). 6 Press the PTT switch or Side 2 key to initiate the call. • "COMPLETE" appears on the display when the status has been successfully transmitted. ■ Receiving A calling ID or text message will appear when a Status call is received. Press any key to return to normal operation. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
18
STATUS MESSAGE (TYPES I AND II ONLY)
You can send and receive 2-digit Status messages which may
be decided in your talk group.
Messages can contain up to 16
alphanumeric characters.
Status messages range from 10 to
99 (80 ~ 99 are reserved for special messages).
A maximum of 15 received messages (combined status
messages and short messages) can be stored in the stack
memory of your transceiver.
■
Transmitting
1
Select your desired zone and channel.
2
Press the key programmed as
[Status]
to enter Status
mode (proceed to step 5) or
[Selcall + Status]
to enter
Selcall mode (proceed to step 3).
3
Press
the
<B
or
C>
key
to select the station you want to call.
•
If Manual Dialing is enabled, you can enter a station ID by
using the DTMF keypad, or by using the
Selector
.
When
using the
Selector
, cycle through the digits to select a
digit, then press the
S
key to set the digit and move the
cursor to the right.
Repeat this process until the entire ID
is entered.
4
Press
the
S
or
key
to enter Status mode.
5
Press
the
<B
or
C>
key
to select the status you want to
transmit.
•
If Manual Dialing is enabled, you can enter a status ID by
using the DTMF keypad, or by using the
Selector
(refer to
step 3, above).
6
Press the
PTT
switch or
Side 2
key to initiate the call.
•
“COMPLETE” appears on the display when the status has
been successfully transmitted.
■
Receiving
A calling ID or text message will appear when a Status call
is received.
Press any key to return to normal operation.