Kenwood NX-320 Operation Manual - Page 16

Installing The Belt Clip, Installing The Cap Over The Speaker/ Microphone Jacks

Get Kenwood NX-320 PDF manuals and user guides View all Kenwood NX-320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

INSTALLING THE BELT CLIP Note: When first installing the belt clip, you must remove the battery pack from the rear of the transceiver. 1 Remove the 2 screws from the rear of the transceiver, then remove the small, plastic black covering that was held in place. 2 Insert the belt clip mount into the space on the rear of the transceiver. 3 Using the 2 screws, affix the belt clip in place. Plastic covering • When the belt clip is not installed, leave the plastic covering in place. • Do not use glue which is designed to prevent screw loosening when installing the belt clip, as it may cause damage to the transceiver. Acrylic ester, which is contained in these glues, may crack the transceiver's back panel. INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS Install the cap over the speaker/ microphone jacks when not using an optional speaker/ microphone. Note: To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cap. 1 Place the cap over the jacks so that the locking tabs insert into the transceiver grooves. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
4
INSTALLING THE BELT CLIP
Note:
When first installing the belt clip, you must remove the
battery pack from the rear of the transceiver.
1
Remove the 2 screws from the
rear of the transceiver, then
remove the small, plastic black
covering that was held in place.
2
Insert the belt clip mount into
the space on the rear of the
transceiver.
3
Using the 2 screws, affix the belt
clip in place.
•
When the belt clip is not installed, leave the plastic covering in
place.
•
Do not use glue which is designed to prevent screw loosening
when installing the belt clip, as it may cause damage to the
transceiver. Acrylic ester, which is contained in these glues, may
crack the transceiver’s back panel.
INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS
Install the cap over the speaker/ microphone jacks when not
using an optional speaker/ microphone.
Note:
To keep the transceiver water resistant, you must cover the
speaker/ microphone jacks with the supplied cap.
1
Place the cap over the jacks so that the
locking tabs insert into the transceiver
grooves.
Plastic
covering