Kenwood VR-5700 User Manual - Page 79

Cd2/tape2 Monitor

Get Kenwood VR-5700 PDF manuals and user guides View all Kenwood VR-5700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Sound Sound I don't hear any sound at all Check that: • The volume is set at the proper level. See "Adjusting the Volume" on page 10 of this manual. • Mute is OFF. If the MUTE indicator on the front of the receiver is blinking, MUTE is ON. See "Muting Sound" on page 16 of this manual. • The proper input (e.g., CD player, Tuner, etc.) has been selected on the Remote Control unit. See "How Do I Operate Devices?" on page 36 of this manual. • The proper zone has been selected. See "How Do I Switch Control Modes?" on page 54 of this manual. • The CD2/TAPE2 MONITOR input has not been selected. (If it has, the CD2/TAPE2 MONITOR indicator on the receiver's front panel will be lit). See "What's on the Front Panel of Your Kenwood Audio Video Receiver?" on page 2 of this manual. • The input mode matches the input signal (e.g., analog vs. digital) that has been set. See "Switching Input Modes" on page 23 of this manual. • The correct Input Mode (e.g., Full Auto) has been set for the digital input. See "Input Modes" on page 22. • The correct speakers have been activated. See "Turning the Speakers On" on page 9 of this manual. Audio is not output only when a 96k fs compatible disc is played. • The optical cable may be bent. Use a new optical cable. • Check that the optical cable connector is connected properly. • Certain DVD player models inhibit digital output. Use analog cables with such a DVD player. The 96k fs indicator does not light while a 96k fs compatible disc is being played. • The indicator will not light unless the DVD player is properly set. 71 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
71
Troubleshooting
Sound
Sound
I don
’
t hear any sound at all
Check that:
•
The volume is set at the proper level. See
“
Adjusting the Volume
”
on
page 10 of this manual.
•
Mute is
OFF
. If the
MUTE
indicator on the front of the receiver is
blinking,
MUTE is ON
. See
“
Muting Sound
”
on page 16 of this
manual.
•
The proper input (e.g., CD player, Tuner, etc.) has been selected on
the Remote Control unit. See
“
How Do I Operate Devices?
”
on page 36
of this manual.
•
The proper zone has been selected. See
“
How Do I Switch Control
Modes?
”
on page 54 of this manual.
•
The
CD2/TAPE2 MONITOR
input has not been selected. (If it has,
the
CD2/TAPE2 MONITOR
indicator on the receiver
’
s front panel
will be lit). See
“
What
’
s on the Front Panel of Your Kenwood Audio -
Video Receiver?
”
on page 2 of this manual.
•
The input mode matches the input signal (e.g., analog vs. digital) that
has been set. See
“
Switching Input Modes
”
on page 23 of this manual.
•
The correct Input Mode (e.g., Full Auto) has been set for the digital
input. See
“
Input Modes
”
on page 22.
•
The correct speakers have been activated. See
“
Turning the Speakers
On
”
on page 9 of this manual.
Audio is not output only when a 96k fs compatible disc is played.
•
The optical cable may be bent. Use a new optical cable.
•
Check that the optical cable connector is connected properly.
•
Certain DVD player models inhibit digital output. Use analog cables
with such a DVD player.
The 96k fs indicator does not light while a 96k fs compatible disc is
being played.
•
The indicator will not light unless the DVD player is properly set.