Kenwood VR-5700 User Manual - Page 83

Remote Control unit

Get Kenwood VR-5700 PDF manuals and user guides View all Kenwood VR-5700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Video/Remote Control unit • Check that the correct video input on the TV is selected. • Check that the video software you record does not have copy guard protection. • All Zone B inputs must be composite. S-Video is not supported in Zone B. Remote Control unit My Remote Control unit is slow to respond-sometimes I have to press buttons or select commands several times • If Remote Control unit is in sleep mode (the screen is blank), the first button press "wakes it up". The second press performs the action. • Your Remote Control unit supports 2-way communication with the receiver. If the 2-way communication indicator on the front of the receiver is lit, Remote Control unit is receiving information. It cannot transmit your new command until it is finished receiving information from the receiver. My Remote Control unit is not responding • Make sure you are within the operating range for Remote Control unit. See "Remote controllable range" on page 7 of this manual. • Replace the batteries. See Chapter Two of the Connections and Setup Guide. • If you're using an IR receiver, make sure it is connected properly and turned on. See Chapter four of the Connections and Setup Guide. • Check the contrast of the LCD display is adjusted properly. See "How Do I Adjust the LCD Display" on page 50. • When the RF ON/OFF (INPUT MODE) button is pressed for 2 sec- onds or longer, "RF OFF" will be displayed. In this condition, the main unit can not receive remote control signals. Press the RF ON/ OFF (INPUT MODE) button again for at least 2 seconds to display "RF ON". See page 49 of the Connections and Setup Guide. • If you want to use Remote Control unit by setting the control mode to Zone B, make sure that the Multi-Zone function is On. If this function is Off, you cannot control Zone B from Remote Control unit. 75 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
75
Troubleshooting
•
Check that the correct video input on the TV is selected.
•
Check that the video software you record does not have copy guard
protection.
•
All Zone B inputs must be composite. S-Video is not supported in
Zone B.
Remote Control unit
My Remote Control unit is slow to respond
—
sometimes I have to
press buttons or select commands several times
•
If Remote Control unit is in sleep mode (the screen is blank), the first
button press
“
wakes it up
”
. The second press performs the action.
•
Your Remote Control unit supports 2-way communication with the
receiver. If the 2-way communication indicator on the front of the
receiver is lit, Remote Control unit is receiving information. It cannot
transmit your new command until it is finished receiving informa-
tion from the receiver.
My Remote Control unit is not responding
•
Make sure you are within the operating range for
Remote Control
unit. See
“
Remote controllable range
”
on page 7 of this manual.
•
Replace the batteries. See Chapter Two of the
Connections and Setup
Guide
.
•
If you
’
re using an IR receiver, make sure it is connected properly and
turned on. See Chapter four of the
Connections and Setup Guide
.
•
Check the contrast of the LCD display is adjusted properly. See
“
How
Do I Adjust the LCD Display
”
on page 50.
•
When the
RF ON/OFF (INPUT MODE)
button is pressed for 2 sec-
onds or longer,
“
RF OFF
”
will be displayed. In this condition, the
main unit can not receive remote control signals. Press the
RF ON/
OFF (INPUT MODE)
button again for at least 2 seconds to display
"RF ON". See page 49 of the
Connections and Setup Guide
.
•
If you want to use Remote Control unit by setting the control mode
to Zone B, make sure that the Multi-Zone function is On. If this func-
tion is Off, you cannot control Zone B from Remote Control unit.
Video/Remote Control unit