Kenwood VR-5900 User Manual - Page 110

Video

Get Kenwood VR-5900 PDF manuals and user guides View all Kenwood VR-5900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Video/PowerTouch III Video I can't see the program I'm playing on the TV. There wasn't any video output to my VCR when I recorded. • Check that the correct video input on the TV is selected. • Check that the video software you record does not have copy guard protection. • All Zone B inputs must be composite. S-Video is not supported in Zone B. PowerTouch III I don't see icons for all my devices. You must identify devices for PowerTouch III control for them to appear in the icon bar on PowerTouch III. See Chapter Two of the Connections and Setup Guide. I don't see icons for all the devices I set up. Some of the device icons appear only when PowerTouch III is set up to control Zone A and some appear only when PowerTouch III is set up to control Zone B. See "Why Don't I See All My Devices?" on page 92 of this manual. When I select a device icon, I don't see any commands. • When you start PowerTouch III for the very first time, all the possible icons appear. If you select any of them, there will be no commands in the command area. You must set up PowerTouch III before you can begin controlling devices. See Chapter Two of the Connections and Setup Guide. • Re-enter the setup code for the device. See Chapter Two of the Connections and Setup Guide. My PowerTouch III is slow to respond-sometimes I have to press buttons or select commands several times. • If PowerTouch III is in sleep mode (the screen is blank), the first but- ton press "wakes it up". The second press performs the action. • Your PowerTouch III supports 2-way communication with the receiver. If the Two-way communication indicator on the receiver's front panel is lit, PowerTouch III is receiving information. It cannot transmit your new command until it is finished receiving information from the receiver. 102 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
102
Troubleshooting
Video/PowerTouch III
Video
I can
’
t see the program I
’
m playing on the TV.
There wasn
’
t any video output to my VCR when I recorded.
•
Check that the correct video input on the TV is selected.
•
Check that the video software you record does not have copy guard
protection.
•
All Zone B inputs must be composite. S-Video is not supported in
Zone B.
PowerTouch III
I don
’
t see icons for all my devices.
You must identify devices for PowerTouch III control for them to appear
in the icon bar on PowerTouch III. See Chapter Two of the
Connections
and Setup Guide
.
I don
’
t see icons for all the devices I set up.
Some of the device icons appear only when PowerTouch III is set up to
control Zone A and some appear only when PowerTouch III is set up to
control Zone B. See
“
Why Don
’
t I See All My Devices?
”
on page 92 of this
manual.
When I select a device icon, I don
’
t see any commands.
•
When you start PowerTouch III for the very first time, all the possible
icons appear. If you select any of them, there will be no commands in the
command area. You must set up PowerTouch III before you can begin
controlling devices. See Chapter Two of the
Connections and Setup Guide
.
•
Re-enter the setup code for the device. See Chapter Two of the
Con-
nections and Setup Guide
.
My PowerTouch III is slow to respond
—
sometimes I have to press
buttons or select commands several times.
•
If PowerTouch III is in sleep mode (the screen is blank), the first but-
ton press
“
wakes it up
”
. The second press performs the action.
•
Your PowerTouch III supports 2-way communication with the receiver. If
the Two-way communication indicator on the receiver
’
s front panel is
lit, PowerTouch III is receiving information. It cannot transmit your new
command until it is finished receiving information from the receiver.