KitchenAid KUBR314KSS Owners Manual - Page 5

Installation, Instructions

Get KitchenAid KUBR314KSS PDF manuals and user guides View all KitchenAid KUBR314KSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Glass door overlay panel - Preparation: Create the custom overlay panel using the dimensions shown in the illustration " Glass door overlay panel and hinge routing dimensions". Route shaded areas to a 1/2" (12 mm) depth as shown. IMPORTANT: The following graphic shows a custom panel for a door with the hinges installed on the right-hand side. If your beverage center has the hinges installed on the lefthand side, rotate the custom frame 180° so the hinge markings will be on the left. 1/8" (3 mm) 1/4" (7 mm) 415/16" (125 mm) 2" (53 mm) 1/2" (12 mm) 233/4" (60.3 cm) 171/16" (43.3 cm) 2113/16" (55.4 cm) 305/8" (77.75 cm) Glass door overlay panel and hinge routing dimensions Electrical Requirements Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Before you move your beverage center into its final location, it is important to make sure you have the proper electrical connection. Recommended grounding method: A 115 V, 60 Hz, AC only, 15 A or 20 A fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your beverage center be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord. NOTE: Before performing any type of installation, cleaning, or removing a light bulb, unplug beverage center or disconnect power. INSTALLATION INSTRUCTIONS Unpack the Beverage Center Handle (optional) Custom handles are typically attached to the custom overlay door panel only. Refer instructions received with KitchenAid handle kits to install these handles on custom wood panels. Custom handle needs to be installed on the door panel with countersunk holes and installed before the custom overlay door panel has been installed on the beverage center door. Excessive Weight Hazard Use two or more people to move and install or uninstall appliance. Failure to do so can result in back or other injury. Before using your beverage center, all packaging materials should be removed and the interior should be cleaned. Remove tape and glue residue from surfaces before turning on the beverage center. With your fingers, rub a small amount of liquid dish soap over any adhesive and wipe with warm water to remove. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These can damage the surfaces of your beverage center. For more information, refer "Beverage Center Safety" section. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
2"
(53 mm)
1/4"
(7 mm)
1/8"
(3 mm)
1/2"
(12 mm)
4
15
/
16
”
(125 mm)
23
3
/
4
”
(60.3 cm)
17
1
/
16
”
(43.3 cm)
21
13
/
16
”
(55.4 cm)
30
5
/
8
”
(77.75 cm)
Glass door overlay panel - Preparation:
Create the custom overlay panel using the dimensions shown
in the illustration “ Glass door overlay panel and hinge routing
dimensions”. Route shaded areas to a 1/2” (12 mm) depth as
shown.
IMPORTANT:
The following graphic shows a custom panel for
a door with the hinges installed on the right-hand side.
If your beverage center has the hinges installed on the left-
hand side, rotate the custom frame 180° so the hinge markings
will be on the left.
Glass door overlay panel and hinge routing dimensions
Handle (optional)
Custom handles are typically attached to the custom overlay
door panel only.
Refer instructions received with KitchenAid handle kits to
install these handles on custom wood panels.
Custom handle needs to be installed on the door panel with
countersunk holes and installed before the custom overlay
door panel has been installed on the beverage center door.
Electrical Requirements
Before you move your beverage center into its final location,
it is important to make sure you have the proper electrical
connection.
Recommended grounding method:
A 115 V, 60 Hz, AC only, 15 A or 20 A fused, grounded
electrical supply is required. It is recommended that a
separate circuit serving only your beverage center be
provided. Use an outlet that cannot be turned off by a switch.
Do not use an extension cord.
NOTE:
Before performing any type of installation, cleaning, or
removing a light bulb, unplug beverage center or disconnect
power.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
INSTALLATION
INSTRUCTIONS
Unpack the Beverage Center
Excessive Weight Hazard
Use two or more people to move and install or uninstall
appliance.
Failure to do so can result in back or other injury.
Before using your beverage center, all packaging materials should
be removed and the interior should be cleaned.
±
Remove tape and glue residue from surfaces before turning on
the beverage center. With your fingers, rub a small amount of
liquid dish soap over any adhesive and wipe with warm water
to remove.
±
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue.
These can damage the surfaces of your beverage center.
For more information, refer “Beverage Center Safety” section.
5