Kodak DP2900 User's Guide - Page 46

Heading2 - Replacing the Projection Lamp

Get Kodak DP2900 - Digital Projector PDF manuals and user guides View all Kodak DP2900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

User Guide KODAK DP2900 Digital Projector Replacing the Projection Lamp Warning: To avoid burns, allow the projector to cool for at least 30 minutes before you open the lamp module door. Never extract the lamp module while the lamp is operating. The lamp hour counter in the Status menu counts the number of hours the lamp has been in use. Replace the lamp when the brightness is no longer acceptable. To order replacement lamp modules contact your dealer of KODAK products or visit our Web site at www.kodak.com/ go/projectors. Follow these steps to replace the projection lamp: 1. Turn off the projector by unplugging the power cord. 2. Wait 30 minutes to allow the projector to cool thoroughly. 3. Invert the projector on a soft flat surface, then insert a small screwdriver or other flat object into the tab on the lamp module door.. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
User Guide KODAK DP2900 Digital Projector
46
Replacing the Projection Lamp
Warning: To avoid burns, allow the projector to cool for at least 30
minutes before you open the lamp module door. Never
extract the lamp module while the lamp is operating.
,PSRUWDQW± 7KH²ODPS²LQ²WKH².2’$.²’3¹¸··²FRQWDLQV²WUDFH²DPRXQWV²RI²PHUFXU\µ²
6RPH²JRYHUQPHQWV²UHTXLUH²VSHFLDO²GLVSRVDO²RI²ODPSV²FRQWDLQLQJ²PHUFXU\µ²
’LVSRVH²RI²ODPSV²LQ²DFFRUGDQFH²ZLWK²WKH²ODZ²DQG²DQ\²DSSOLFDEOH²ORFDO²
UHJXODWLRQVµ
The lamp hour counter in the Status menu counts the number of hours
the lamp has been in use. Replace the lamp when the brightness is no
longer acceptable. To order replacement lamp modules contact your
dealer of KODAK products or visit our Web site at www.kodak.com/
go/projectors.
Follow these steps to replace the projection lamp:
1.
Turn off the projector by unplugging the power cord.
2.
Wait 30 minutes to allow the projector to cool thoroughly.
3.
Invert the projector on a soft flat surface, then insert a small
screwdriver or other flat object into the tab on the lamp module
door.
.