Konica Minolta bizhub PRESS 1250 Watkiss PowerSquare 2-Knife Trimmer User Manu
Konica Minolta bizhub PRESS 1250 Manual
View all Konica Minolta bizhub PRESS 1250 manuals
Add to My Manuals
Save this manual to your list of manuals |
Konica Minolta bizhub PRESS 1250 manual content summary:
- Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 1
Watkiss P2T 2-Knife Trimmer User Manual English, Issue 1, November 2014 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 2
© Watkiss Automation Limited 2014 All Rights Reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. Warranty The information contained in this document is subject to change without notice. Watkiss Automation - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 3
-fit the Side-Trimmer Book Supports 17 5. Error Conditions, Problems and Solutions 23 Side-Trimmer Error 23 Quality Problems 23 Side-Trimmer Message List 28 Paper Jams 31 Change the Fuses - Side-Trimmer 31 continued . . . User Manual for - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 4
6. Maintenance 33 Service Maintenance 33 Operator Maintenance 33 7. Specifications 35 8. Declaration of Conformity 37 ii Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 5
and Caution Messages The warning and caution messages used in this manual are shown below. WARNING: A WARNING message tells you that a procedure or operation can be dangerous. To prevent injury, you must follow the instructions. CAUTION: A CAUTION message tells you that a procedure or operation can - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 6
Installation Your Side-Trimmer must be installed by a Watkiss approved service engineer. Special knowledge is needed to install the machine. CAUTION: you have any questions or problems, refer to the problem solving section in this manual (see "Error Conditions, Problems and Solutions" on page 23 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 7
ON/OFF The mains power ON/OFF switch turns ON the switch Side-Trimmer or turns OFF the Side-Trimmer. Watkiss P2T 2-Knife Trimmer User Manual 3 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 8
the Side-Trimmer No. Component Function 8 Fuses The fuses make sure the operator and the machine are protected if there is an electrical problem or short circuit. 9 Rating and serial label The rating label displays the type of machine, serial number, power use and fuse information. 4 Watkiss - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 9
according to the PAGE SIZE. • To change the size and trim position, touch SIDE TRIM. See "Side-Trim" on page 8. Watkiss P2T 2-Knife Trimmer User Manual 5 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 10
Adjust the Stacker • If the side-trim size is 190mm or less, remove the book supports. See "Remove and re-fit the Side-Trimmer Book Supports" on page 46. Adjust the Stacker Adjust the stacker according to the size and thickness Side-Trim Bin" on page 13. 6 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 11
CHAPTER 3 The User Interface FIGURE 3. The booklet maker Touch Screen Side-Trimmer adjustment Watkiss P2T 2-Knife Trimmer User Manual 7 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 12
shows if the trim is offset from the centre-line. A red X shows that the side-trim function is not active. 8 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 13
-trim dimension. - TRIM OFFSET By default, the book is trimmed equally on both sides. Touch '+' or '-' to move the trim position away from the centre line. The range is -40mm to +40mm, dependent on how much is to be trimmed. The default setting is 0mm. Watkiss P2T 2-Knife Trimmer User Manual 9 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 14
make changes to the configuration of the Some functions and buttons are only available at certain access levels. Refer to your booklet maker manual. Button Information Hidden Active Visible Operator Supervisor - SIDE TRIM (P2T) Touch SIDE TRIM (P2T) to switch off communication to the Side - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 15
are needed in the day-to-day operation of your Side-Trimmer. Adjust the Side-Trim Offset Introduction By default, the book is side-trimmed by an equal amount on each side. The side-trim dimension is automatically book delivery out of the Side-Trimmer. Watkiss P2T 2-Knife Trimmer User Manual 11 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 16
side-trim offset 1. Touch BASIC > SIDE TRIM and then touch '+' or ' - ' to adjust the TRIM OFFSET. 2. Touch CLOSE to close the window. Select the default side-trim offset 1. Touch BASIC > SIDE TRIM and then touch AUTO. 2. Touch CLOSE to close the window. 12 Watkiss P2T 2-Knife Trimmer User - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 17
-trim bin under the chute. Check the bin is positioned close to the machine. Magnets hold the bin in position. Watkiss P2T 2-Knife Trimmer User Manual 13 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 18
tray Set the collection table position according to the size of the book. Read the setting through the window. 14 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 19
release handle FIGURE 9. The stacker FIGURE 10. The stacker in raised position Procedure - Raise the stacker 1. Press down on the top of the stacker, beside the green belts. 2. At the same time, push down on of the stacker until it clicks into position. Watkiss P2T 2-Knife Trimmer User Manual 15 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 20
chain allows. cables. When needed, rotate the Side-Trimmer back to the docked position, the latch will click closed. 16 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 21
) 1. Outer book support, left (marked LH OUT) 2. Inner book support, left (marked LH IN) 3. Centre book support 4. Inner book support, right (marked RH IN) 5. Outer book support, right (marked RH OUT) FIGURE 14. Side-Trimmer book supports Watkiss P2T 2-Knife Trimmer User Manual 17 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 22
4 - Standard Tasks - Remove and re-fit the Side-Trimmer Book Supports Top Cover Outfeed Guard FIGURE 15. The side-trimmer Procedure - Removal Step 1 - preparation Use PAPER SIZE to set the paper the top cover of the Side-Trimmer. See Figure 15 on page 18. 18 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 23
supports There are two inner book supports. Remove one at a time. Hold each end of the inner book support and lift upwards. Remove the inner book support through the top of the machine. Repeat with the other inner book support. Inner book support (right) Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 24
on page 17. On each book support, there are semicircular cut outs at each end. Position the cut-outs over the fixing points. Press down on the book support so that it fits onto the fixing points. Fixing Repeat with the other book supports. Cut-out 20 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 25
the outfeed guard open with one hand and slide the centre book support in though the opening. Keep the book support central. See Figure 15 on page 18 The centre book support is secured with spring clips. Hold the the centre book support with two hands. Lift and slide forwards until it clips onto - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 26
4 - Standard Tasks - Remove and re-fit the Side-Trimmer Book Supports 22 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 27
screen. See "Side-Trimmer Message List" on page 28. Refer also to your booklet maker user manual. Quality Problems Fore-edge trim Side-Trim Side-Trim FIGURE 16. Fore-edge trimming and side-trimming Trimming problems can affect the fore-edge trim or the side-trim. Make sure you follow the correct - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 28
in the SIDE TRIM window? No Yes Set SIDE TRIM to AUTO. Does the problem continue? Yes No Further action is not needed. If you need to use a cover of the side-trimmer. Wait for the side-trimmer to reset. Does the problem continue? Yes No Further action is not needed. Turn off the Side-Trimmer at - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 29
Problems and Solutions - Quality Problems Side-Trimming problem Does the problem continue? problem continue? Yes No Further action is not needed. Call your service engineer. Side-Trimming problem - the book is only trimmed on one side This problem Does the problem continue? Does the problem continue? - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 30
-Trimmer Book Supports" on page 17. Does the problem continue? Yes No No further action is needed. Turn off the Side-Trimmer at the mains ON/OFF switch. Wait for 5 seconds and then turn on the Side-Trimmer. Does the problem continue? Yes No Further action is not needed. Call your service engineer - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 31
the Side-Trimmer Book Supports" on page 17. Call your service engineer if there are marks on the trimmed edge different to a normal witness mark or if the edge is badly trimmed. Side-Trimming problem - cannot enter settings and/or the amount of trim. Watkiss P2T 2-Knife Trimmer User Manual 27 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 32
at least 5 seconds and then turn the side-trimmer ON. If the problem continues, then call your service engineer. Open and then close the top cover of the side-trimmer. Then side-trimmer ON. If the problem continues, then call your service engineer. 28 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 33
at least 5 seconds and then turn the side-trimmer ON. If the problem continues, then call your service engineer. The side-trim axis is moving. This message clears when the adjustment -trimmer ON. If the problem continues, then call your service engineer. Watkiss P2T 2-Knife Trimmer User Manual 29 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 34
problem continues, then call your service engineer. SYSTEM ERROR 41.39 If the side-trimmer setting is 190mm or less, check that the book supports are removed. Otherwise, follow the instructions If the problem continues, then call your service engineer. 30 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 35
wait at least 5 seconds and then turn the side-trimmer ON. If the problem continues, then call your service engineer. Change the Fuses - Side-Trimmer Introduction The Side-Trimmer has two fuses fuse breaks again, then call your Watkiss service engineer. Watkiss P2T 2-Knife Trimmer User Manual 31 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 36
5 - Error Conditions, Problems and Solutions - Change the Fuses - Side-Trimmer 32 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 37
a Watkiss approved service engineer can service the Side-Trimmer. Contact your supplier for further information. Operator Maintenance We recommend that you clean the Side-Trimmer every week to remove surface dust. CAUTION: Only clean the machine with materials that are recommended in this manual. Do - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 38
6 - Maintenance - Operator Maintenance 34 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 39
Maximum trim width: 380mm (no trim); 378mm (trimmed) Maximum side trim: 40mm each side Minimum side trim: 1mm each side Watkiss P2T 2-Knife Trimmer User Manual 35 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 40
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area this product at any time without notice. 36 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 41
: 2011/65/EC Council Directive WEEE: 2002/96/EC Council Directive amended by 2008/34/EC and 2008/35/EC Watkiss P2T 2-Knife Trimmer User Manual 37 - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 42
8 - Declaration of Conformity - Reach: REGULATION (EC) No. 1907/2006 M C Watkiss Technical Director, Watkiss Automation Ltd. 21 May 2013 38 Watkiss P2T 2-Knife Trimmer User Manual - Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 43
- Konica Minolta bizhub PRESS 1250 | Watkiss PowerSquare 2-Knife Trimmer User Manu - Page 44
Watkiss Automation Limited 1 Blaydon Road Middlefield Industrial Estate Sandy, Bedfordshire SG19 1RZ United Kingdom Tel: +44 (0)1767 685700 Fax: +44 (0)1767 689900
Watkiss P2T 2-Knife Trimmer
User Manual
English, Issue 1, November 2014