Konica Minolta bizhub PRESS 1250 GP-502 Operation Manual - Page 3

1. Safety THE SAFETY OF YOU AND OTHERS IS VERY IMPORTANT TO GBC. IMPORTANT SAFETY MESSAGES AND INFORMATION ARE CONTAINED IN THIS MANUAL AS WELL AS ON THE MACHINE ITSELF. PLEASE MAKE SURE YOU CAREFULLY READ AND UNDERSTAND ALL OF THESE BEFORE OPERATING THE MACHINE. THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY MESSAGE IN THIS OPERATION INSTRUCTIONS MANUAL. THIS SYMBOL INDICATES A POTENTIAL PERSONAL SAFETY HAZARD THAT COULD HURT YOU OR OTHERS THE FOLLOWING PICTORIAL IS FOUND ON THE GP-502. This safety message means you could get an electrical shock because disconnecting power from this section does not cut off power from adjacent sections of the machine. This safety message means that you might get seriously hurt or killed if you open the product and expose yourself to hazardous voltage. NEVER remove the screwed on covers. ALWAYS refer service • Use the GP-502 only for its intended purpose of punching and binding books using paper and covers according to the indicated specifications. • Retain this Operation Instructions manual for future use. CAUTION: THE PRINTER ON/OFF SWITCH DOES NOT CUT OFF POWER FROM THE BINDER. CAUTION: THE PUNCH ON/OFF SWITCH DOES NOT CUT OFF POWER FROM THE BINDER. • The GP-502 must be connected to a supply voltage corresponding to the electrical rating of the machine operation instructions (also listed on the serial number label). • The grounding plug is a safety feature and will only fit into the proper grounding-type power outlet. If you are unable to insert the plug into an outlet, contact a qualified electrician to have a suitable outlet installed. • Do not alter the plug on the end of the cordset of the GP-502. It is provided for your safety. • Unplug the GP-502 before moving the machine or whenever the machine is not in use for an extended period of time. • Do not operate the GP-502 if the machine has a damaged power supply cord or plug. Do not operate the machine after any malfunction. Do not operate the machine in case of liquid spills, or if the machine has been damaged in any other way. • Do not overload electrical outlets. FCC NOTE (THE FOLLOWING NOTE ONLY APPLIES TO THE UNITS RATED 115V 60HZ.) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Operation Manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. Safety messages CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY GENERAL BINDING CORPORATION COULD VOID YOUR AUTHORITY TO OPERATE THE EQUIPMENT. Canada Class A Notice - Avis Canada, Classe A This Class A digital apparatus complies with Canadian ICES-3. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. MAIN CORDSET SELECTION (THE FOLLOWING NOTE ONLY APPLIES ONLY TO THE UNITS RATED 230V 50HZ, AND LOCATED IN THE EUROPEAN UNION) CAUTION: WHEN CHOOSING A DETACHABLE LINE CORD FOR USE WITH YOUR GP-502, ALWAYS FOLLOW THE FOLLOWING PRECAUTIONS The cordset consists of three parts: the attachment plug, the cord and the appliance inlet. Each of these components must have European regulatory safety approvals. The following minimum electrical ratings for the specific cordset are published for safety purposes. DO NOT USE CORDSETS THAT DO NOT MEET THE FOLLOWING MINIMUM ELECTRICAL REQUIREMENTS. PLUG: 3 amperes, 250 volts, 50/60 Hz, Class 1, 3 conductor, European safety approved. CORD: Type H05VV-F3G0.75, Harmonized (< HAR>). The "< >" symbols indicate cord approved according to appropriate European standard (NOTE: "HAR" may be substituted for approval mark of European safety agency that approved the cord. An example would be "< VDE >"). APPLIANCE CONNECTOR: 3 amperes, 250 volts, 50/60 Hz, European safety approved, Type IEC 320. The cordset shall not exceed 3 meters in length. A cordset with component electrical ratings R e v, 1 . 0 3 J u l y 2 0 1 2