Kyocera KM-C830D KM-C830 Operation Guide Rev-1B

Kyocera KM-C830D Manual

Get Kyocera KM-C830D PDF manuals and user guides View all Kyocera KM-C830D manuals
Add to My Manuals
Save this manual to your list of manuals

Kyocera KM-C830D manual content summary:

  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 1
    Operation Guide * The illustration above shows the copier with the optional original cover installed. Please read the Operation Guide before using the copier. Keep it close to the copier for easy reference.
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 2
    Guide is for the KM-C830 and KM-C830D copiers. The instructions contained herein are based on the KM-C830 standard copier (for 1-sided copies only) and KM-C830D duplex copier (for 2-sided copies). • Standard equipment KM-C830: Two 500-sheet capacity drawers KM-C830D reserved. No part of this material
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 3
    " setting selected G Original G Original G Original G "Smooth" setting selected G "Vivid" setting selected G "Heavy" setting selected NOTE: Samples in this operation guide were created in order simply to indicate the different effects of each function, and the resulting colors will, therefore
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 4
    intensity increased G Yellow intensity decreased G Magenta intensity decreased G Cyan intensity decreased G Black intensity decreased NOTE: Samples in this operation guide were created in order simply to indicate the different effects of each function, and the resulting colors will, therefore
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 5
    plus value selected... Reds near yellow are intensified towards yellow, and cyans near blue intensified towards blue. NOTE: Samples in this operation guide were created in order simply to indicate the different effects of each function, and the resulting colors will, therefore, differ somewhat from
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 6
    page 5-7 for the actual setting procedure.) G Original G Sharpness setting increased G Original G Sharpness setting decreased NOTE: Samples in this operation guide were created in order simply to indicate the different effects of each function, and the resulting colors will, therefore, differ
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 7
    the power plug from the outlet] Always connect the copier to an outlet with a ground connection] Please contact your service representative to order a replacement if the safety warnings in this Operation Guide are illegible or if the guide itself is missing. (fee required) An original which
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 8
    1-1 INSTALLATION PRECAUTIONS 1-2 PRECAUTIONS FOR USE 1-3 Section 2 NAMES OF PARTS 2-1 1. Main body 2-1 2. Operation panel 2-3 G Initial mode 3-5 G When printing onto envelopes 3-6 2. Replacing the toner containers and the waste toner tank 3-8 3. Cleaning the charger 3-11 4. Replacing the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 9
    copiers 6-34 15. Making booklets, etc. from book originals [Book to Book mode] (Only available in duplex copiers 7-29 9 Display contrast adjustment 7-30 0 Management PIN code 7-30 ! Silent mode ON/OFF 7-30 @ Day 8-1 G Names of parts 8-1 G Setting originals 8-5 (9) Network Scanner Kit 8-6 vii
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 10
    TROUBLESHOOTING 9-1 1. If one of the following messages is displayed .......... 9-1 2. If paper jams 9-4 (1) Misfeed location indicators 9-4 (2) Cautions 9-4 (3) Removal procedures 9-5 3. If other trouble occurs 9-16 Section 10 MAINTENANCE AND OPERATION INFORMATION 10-1 1. Cleaning the copier
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 11
    G MAKING FULL USE OF THE COPIER'S ADVANCED FUNCTIONS 1 Having the copier automatically select paper of the same size as the original (Page 4-2) 2 Various functions for making enlarged and reduced copies I Enlarging/reducing
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 12
    MAKING FULL USE OF THE COPIER'S ADVANCED FUNCTIONS 10 Printing page numbers on copies (Page 6-19) 11 Feeding paper as a backing sheet for OHP transparencies
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 13
    COPIER'S ADVANCED FUNCTIONS 23 Using department codes copier from tipping over because of weight in the copier copier. I Casters (Page 8-4) CAUTION To prevent the possibility of accidents due to tilting the copier copier from tipping over, the optional caster kit must be installed when the copier
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 14
    Caution labels have been attached to the copier at the following locations for safety purposes. BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing toner. Label 1, 2 High temperature inside. Do not touch parts in this area, because there is a danger
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 15
    to avoid the danger of fire • To keep the copier cool and facilitate changing of parts and maintenance, allow access space as shown below. Leave not possible, contact your service representative Other precautions • Connect the power plug to the closest outlet possible to the copier. • The power
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 16
    performing cleaning operations • If dust accumulates within the copier, there is a danger of fire or other trouble. It is therefore recommended that you consult with your service representative in regard to cleaning of internal parts. This is particularly effective if accomplished prior to seasons
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 17
    • When lifting or moving the copier, contact your service representative. • Do not touch electrical parts, such as connectors or printed of water. If coughing develops, contact a physician. . If you do happen to ingest toner, rinse your mouth out with water and drink 1 or 2 cups of water to dilute
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 18
    Section 2 NAMES OF PARTS 1. Main body 1 2 3 - 4 0 8 9 ! 56 7 @ # $ % ^ & ° * ¤ ( ) ⁄ › fi ‡ fl , ‹ · 2-1
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 19
    misfeed occurs inside the copier, when you need to replace a toner cartridge, the waste toner tank or the oil copiers [for 2-sided copies]) (This unit allows you to make duplex [2-sided] copies.) Section 2 NAMES OF PARTS fi Paper length guide release levers (Pinch these levers and adjust the guide
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 20
    Section 2 NAMES OF PARTS 2. Operation panel Inch specifications 1 2 3 45 678 9 0! @# ) ° Metric specifications 1 2 3 45 678 9 0! @# ) ° 2-3
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 21
    indicator lights if a printing error occurs when you are using operate the copier as well as when trouble occurs. It page 6-32.) Section 2 NAMES OF PARTS & Duplex / Page Separation key & manually adjust the copy exposure. The lit indicator will show the present copy exposure. See page 4-3.) ¤ Manual
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 22
    NAMES OF PARTS ´ Black&White See page 4-1.) ¨ Copier key (Press this key when you are using the optional printer functions, scanner functions and/or fax "100%" (1:1), the number of copies to be made is set to "1", "manual exposure mode" is selected for the copy exposure and the image quality is set
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 23
    Up to 500 sheets of standard paper (75 g/m2 - 90 g/m2) or color paper can be loaded into the drawer that is included with your copier. Up to 250 sheets of paper can be loaded into each drawer of the optional Paper Feeder. • Standard accessory drawer(s) Standard
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 24
    is to be loaded in that drawer. * The paper sizes are marked on the bottom of the drawer. 4 Pinch the levers for the paper length guide plate and move the plate to fit the length of the paper that is to be loaded in that drawer. * The paper sizes are marked
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 25
    is loaded into that drawer. NOTE If you will not be using the copier for a prolonged period of time, remove all paper from the drawer(s) and paper or larger, be sure to pull out the multi-bypass extension. 2 Adjust the insert guides to fit the width of the paper that is to be set on the multi-bypass
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 26
    onto the copy eject tray. (See ") Eject destination" on page 7-22.) • Be sure to push the multi-bypass extension back in, and open the insert guides as far as they will go BEFORE closing the multibypass tray. Section 3 PREPARATIONS G Setting the paper size for the multi-bypass tray It is necessary
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 27
    . The "Select function" screen will appear. Inch specifications Metric specifications 3 Press the Enter key. If a Memory Copy Board is installed in your copier and you selected "z Transparency Mode", proceed to the next step. 4 Use the M cursor or the N cursor key to select "c OHP film". The
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 28
    -bypass tray for printing. Up to 10 envelopes can be set on the multi-bypass tray at a time. For more details, refer to the Operation Guide for the Printer Kit. Refer to the following table for the types and sizes of envelopes that can be used in this machine. Acceptable envelope
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 29
    with the print side face-up and the flap side towards the front of the copier or towards the leading edge of insertion. Then slide them all the way into the multi-bypass tray, along the insert guides, as far as they will go. * The proper orientation will actually depending upon the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 30
    tank. Dangerous sparks may cause burns. CAUTION DO NOT attempt to force open or destroy the toner containers or the waste toner tank. 4 Insert the new container into the copier. * Once it is inserted properly, the new container will lock into place. The illustrations in the following procedure
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 31
    , as there is a danger of electrical shock. CAUTION The copier's fixing unit is extremely hot. Take sufficient care when working toner containers or the waste toner tank. 8 Use the cap that is located on top of the waste toner tank to seal to the opening in the tank. 7 Push down on the waste toner
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 32
    10 Set the new waste toner tank into the copier. * Once it is inserted properly, the new waste toner tank will lock into place. to come out dirty. 3 G After use, ALWAYS dispose of the toner containers and the waste toner tank in accordance with Federal, State and Local rules and regulations. 11
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 33
    3 times. 2 1 3 3 Take the supplied grid cleaner out of its package and remove the cap. 6 Lift up on the main charger release lever and push the main charger back into its original position in the copier. NOTE The sponge portion of the grid cleaner contains fluid. Perform the cleaning operation
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 34
    7 Remove the grid cleaner. Section 3 PREPARATIONS NOTE DO NOT attempt to reuse the grid cleaner after it is used once. 8 Grasp the green cleaning shaft (shown as 4 in the illustration), pull it out slowly as far as it will go and then push it back in all the way. Repeat this step 5 to 7 times. 4 9
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 35
    High voltage is present in the charger section. Take sufficient care when working in this area, as there is a danger of electrical shock. CAUTION The copier's fixing unit is extremely hot. Take sufficient care when working in this area, as there is a danger of getting burned. 5 Remove the new oil
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 36
    6 Set the new oil roller in the copier. As shown in the illustration, press down on the areas marked "PUSH HERE" and lock the oil roller securely into place. PUSH HERE you removed in step 5 and insert it into the supplied disposable plastic bag. 8 Push the paper conveyor back into the copier. 3-14
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 37
    NOTE See "G Setting originals in the SRDF" on page 8-2 for instructions on how to set originals in your document feeder. Inch specifications Metric A.C.S. key and "ACS" will appear in the message display. The copier will automatically detect whether the original is color or monochrome (B/W) and the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 38
    optional DF must be installed in your copier in order to use this mode. *3: Only available in duplex copiers. Inch specifications Metric specifications 5. Selecting key and select the desired size of paper, and then press the Manual key. NOTE It is also possible for you to specify one drawer
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 39
    is possible for you to change the default setting for the copy exposure to the manual exposure mode. (See "1 Exposure mode" on page 7-17.) • The auto exposure (eco mode): Select this mode when you are want to save on toner usage. (The copy image will be relatively light and the colors will change
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 40
    copy." is shown in the message display, copying is possible. 10 CAUTION If the copier will not be used for a short period of time (overnight, etc.), turn the • This product engages a cooling fan in order to cool off internal parts even after the main switch is turned OFF. In order to maintain its
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 41
    Section 5 COLOR COPY SETTINGS 1. Mono-color mode By selecting one color between cyan, magenta, yellow, red, green and blue, it is possible for you to make copies of that color, regardless of the type of original being copied. 1 Press the Digital Editing key to light the corresponding indicator.
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 42
    2. Gloss mode Select the gloss mode when you want to make high-gloss copies. NOTES • This mode is only available when copying onto plain color copy paper. • This mode is NOT available with 2-sided copying. • Copying will take more time than usual when the gloss mode is selected. • The effect from
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 43
    Section 5 COLOR COPY SETTINGS 3. One-touch image quality adjustment Select the image quality, for example "Vivid" or "Calm", according to the type of copy image you want. NOTES • This setting is only available with full color copying. • This setting is NOT available in the auto exposure mode. •
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 44
    4. Adjusting the color balance The color balance can be fine-adjusted by increasing or decreasing the intensity of each of the colors: cyan, magenta, yellow or black. NOTES • These adjustments are only available with full color copying. • These adjustments are NOT available in the auto exposure mode
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 45
    Section 5 COLOR COPY SETTINGS 5. Adjusting the color hue It is possible for you to change the color hue and create copies of interesting colors. For example, turns reds into reddish-yellows or yellows into yellow-greens. NOTES • These adjustments are only available with full color copying. • These
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 46
    [Example 1] If you select "Yellow - Blue" ["Y-B"] and then select a minus value, greens near yellow will be intensified towards yellow and magentas near blue towards blue. (See sample 1 on page iii.) Section 5 COLOR COPY SETTINGS [Example 2] If you select "Yellow - Blue" ["Y-B"] and then select a
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 47
    Section 5 COLOR COPY SETTINGS 6. Adjusting the sharpness This setting adjusts the contours of the image. When, for example, copying originals that were written in pencil, if the text or lines are blurred or broken, increase the sharpness setting (select a plus value) and the text and lines should be
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 48
    Section 6 FUNCTIONS 1. Making enlarged and reduced copies (1) Auto magnification selection mode With this mode, the original image is enlarged/reduced automatically according to the selected paper size. 3 Press the Start key to begin the copying procedure. Inch specifications Metric
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 49
    (2) Zoom mode With this mode, the magnification ratio can be set to any 1% increment between 25% and 400%. 1 Set the original to be copied. 2 Use the Zoom(+) or the Zoom(-) key, as appropriate, to change the displayed magnification ratio to the desired ratio. Inch specifications Metric
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 50
    Section 6 FUNCTIONS 4 Press the Enter key. The message display will return to the "Ready to copy." screen and the selected ratio will be shown in the display. Inch specifications Metric specifications (4) XY zoom mode With this mode, it is possible for you to change the length and width of the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 51
    4 Use the Zoom(+) or Zoom(-) key to specify the desired ratio for the width of the image. It is also possible for you to enter the ratio directly using the numeric keys on the keypad. Inch specifications Section 6 FUNCTIONS 8 Use the M cursor key to select "z Enter" and then press the Enter key.
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 52
    Section 6 FUNCTIONS 2. Interrupt copying Interrupt copying is useful if, during one copy job, you want to copy other originals at different settings. Once the rush job is completed, the interrupted copy job can be resumed at the same settings as before. 4 When copying is completed, press the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 53
    paper sizes between 5 1/2" x 8 1/2" and 11" x 17" [between A5R and A3] can be used in this mode. • The optional DF must be installed in your copier. 1 Left side binding: Open-faced originals are copied from the left side page first. 2 Right side binding: Open-faced originals are copied from the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 54
    Section 6 FUNCTIONS (3) Making duplex (2-sided) copies from one-sided originals With this mode, multiple one-sided originals are copied onto the front and back sides of the copy paper. If you are copying an odd number of originals, the back side of the last page will be blank. 1 Set the original to
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 55
    6 Select whether you want the image that is copied onto the back side of the copy to be rotated 180 degrees or not. Inch specifications Metric specifications Section 6 FUNCTIONS 11 Replace the first original with the next one and press the Start key. Scanning of that next original will start.
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 56
    of paper. NOTES • Only 11" x 8 1/2" [B5R and A4] size originals can be used in this mode. If the Memory Copy Board is installed in your copier, 8 1/2" x 11" and 11" x 8 1/2" [B5R, B5, A4R and A4] size originals can be used. (A4R paper can be loaded into the optional Paper Feeder, while B5
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 57
    3 Use the M cursor or the N cursor key to select "x Page separation" and then press the Enter key. The "Select 1-sided copy mode." screen will appear. Inch specifications Metric specifications Section 6 FUNCTIONS 7 Press the Enter key. The message display will return to the "Ready to copy." screen
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 58
    mode] NOTE If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. (3) Front & back margin When you are making 2-sided copies, the margin positions and widths can be selected separately
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 59
    1 Set the original to be copied. NOTE Set originals as shown in the illustration. Setting them in the wrong direction may cause the margin to be created in the correct position. Section 6 FUNCTIONS 4 Use the L cursor or the M cursor key to select where you want the margin to be created. Inch
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 60
    Section 6 FUNCTIONS 9 Check the settings shown for the front & back margins. If you want to create the margins at the current settings, press the Enter key. In this case, go directly to step 19. If you want to change the settings, go to the next step. Inch specifications 13 Use the O cursor or the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 61
    17 Use the O cursor or the P cursor key to select the desired margin width. Inch specifications Metric specifications NOTE The margin width can be set to any 1/8" increment between 1/4" and 3/4" [1 mm increment between 1 mm and 18 mm]. 18 Press the Enter key. 19 Use the L cursor key to select "z
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 62
    erase modes] NOTE If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. (3) Selecting the erasing area (Custom erase mode) With this mode, you can make clean, blemish-free copies from
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 63
    2 Press the Digital Editing key to light the corresponding indicator. Inch specifications Metric specifications Section 6 FUNCTIONS 5 Press the Enter key. • If you selected "z Sheet Erase" or "x Book Erase", go to the next step. • If you selected "c Custom Sheet", go directly to step 8. NOTE In
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 64
    the Enter key. The asterisk ( ) will be removed and the setting canceled. NOTE If multiple inverted copies are performed, "Please wait. Adding toner." ["PLEASE WAIT. NOW ADDING TONER."] may appear in the message display. 5 Use the M cursor key to select "z Enter" and then press the Enter key. The
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 65
    Section 6 FUNCTIONS 8. Making mirror image copies [Mirror image mode] With this mode, you can make mirror image copies. 4 Press the Enter key. The mirror image mode will be selected and an asterisk ( ) will appear in front of the number for that setting. NOTE In order to cancel the mirror image
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 66
    size as well. • If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. 1 Set the original to be copied. NOTE Set originals as shown in the illustration. 3 Use the M cursor or the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 67
    6 If you want to change the page on which page numbers will start to be print, use the numeric keys on the keypad or press the O cursor or the P key to change the setting to that desired. Inch specifications Section 6 FUNCTIONS 10 Replace the first original with the next one and press the Start
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 68
    are piled on top of one another, static electricity can cause problems. This mode automatically place a backing sheet between the transparencies during as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. 1 Set the transparency film in the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 69
    3 Press the Transparency Film / Card Stock key to light the corresponding indicator. Inch specifications Metric specifications Section 6 FUNCTIONS 6 Use the M cursor or the N cursor key to select whether you want to have the image copied onto the backing sheets or not. • If you DO want to have
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 70
    copy paper. • If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. (1) Copying onto the backing sheet With this setting, after the original is copied onto the transparency and the same
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 71
    Each transparency and backing sheet will be ejected first, followed by the set of standard copies. • If the optional Document Finisher is installed in your copier, the transparencies and backing sheets will be ejected onto the non-sort tray on the Document Finisher and the standard copy sets will be
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 72
    Section 6 FUNCTIONS 13 Press the Start key. Scanning of the originals will start. • If you set the originals in the optional DF, copying will start automatically. • If you set the original on the platen, go to the next step. Inch specifications Metric specifications 14 Replace the first
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 73
    at all. NOTE If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. * Refer to the following table for the types of finished copies that each combination of settings will make. Back
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 74
    Section 6 FUNCTIONS G Separation insert mode With this mode, sheets can be inserted at specified points among copies of multiple originals. You can also select whether to copy onto the inserted sheets themselves or not. 1 If you choose to copy on the front and back side of the insert sheets... *
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 75
    the corresponding indicator. Inch specifications Metric specifications Section 6 FUNCTIONS 5 Press the Enter key. • If your machine is a duplex copier, go to the next step • If your machine is a standard copier, go directly to step 10. 6 Use the M cursor or the N cursor key to select the type of
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 76
    Section 6 FUNCTIONS 11 Press the Enter key. Perform the procedure below that corresponds to the mode that you selected. • If you selected "z Cover" or "c Cover+Insert" here, go to the next step ("G Cover mode settings"). • If you selected "x Insert" here, go directly to step 21 ("G Separation
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 77
    19 If you are finished changing the settings for the cover mode, use the M cursor key to select "End". Inch specifications Section 6 FUNCTIONS 23 Use the numeric keys on the keypad to enter the page number(s) that will specify where the separation insert sheets will be inserted. The sheets will
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 78
    Section 6 FUNCTIONS 27 Press the Start key. Scanning of the originals will start. • If you set the originals in the optional DF, copying will start automatically. • If you set the original on the platen, go to the next step. Inch specifications Metric specifications 28 Replace the first
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 79
    , dotted line or registration marks (cropmarks). G 4 in 1 Use this mode when you want to copy four originals onto one sheet. If your machine is a duplex copier, this mode can also be used in conjunction with the 2-sided copy modes in order to copy eight originals onto one sheet. (When setting the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 80
    • If necessary, select the location of paper feed. Metric specifications 7 Press the Enter key. • If your machine is a duplex copier, go to the next step. • If your machine is a standard copier, go directly to step 10. 11 Press the Start key. Scanning of the original will start. • If you set the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 81
    format. 1 Press the Book Mode key to light the corresponding indicator. Inch specifications Metric specifications NOTES • This mode is only available in duplex copiers. • If the number of originals is not a multiple of four, the last page(s) of the copies will come out blank. • 2-sided copies
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 82
    Section 6 FUNCTIONS 4 Use the M cursor or the N cursor key to specify the type of originals being copied. Select "z 1-sided" if you are using 1-sided originals and "x 2-sided" if you are using 2-sided originals. Inch specifications 9 Press the Start key. Scanning of the original will start. • If
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 83
    format. 1 Press the Book Mode key to light the corresponding indicator. Inch specifications Metric specifications NOTES • This mode is only available in duplex copiers. • If the number of originals is not a multiple of four, the last page(s) of the copies will come out blank. • 2-sided copies
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 84
    Section 6 FUNCTIONS 4 Use the M cursor or the N cursor key to select the binding direction for the finished copies. Inch specifications 9 Press the Start key. Once the original has been scanned, remove it. Inch specifications Metric specifications Metric specifications 5 Press the Enter key. 6
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 85
    NOTE If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. 1 Press the Book Mode key to light the corresponding indicator. Inch specifications Metric specifications 4 Press the N cursor
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 86
    Metric specifications NOTES • If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. • As there will be some duplication of a portion of the image on each finished copy, if you overlay these
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 87
    7 Use the O cursor or the P cursor key to select the magnification ratio that you want to use. Inch specifications Metric specifications 8 Press the Enter key. The message display will return to the "Ready to copy." screen. 9 Specify the size of the original being copied and select the size of the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 88
    do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. • If your machine is a duplex copier, it is possible for you to make duplex (2-sided) copies in this mode. • Originals can be scanned from both
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 89
    7 Press the Enter key. 8 Press the Paper Select key and specify the paper size. Inch specifications Metric specifications Section 6 FUNCTIONS 11 Replace the first original with the next one and press the Start key. Scanning of that next original will start. Carry out this step for all of the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 90
    Section 6 FUNCTIONS 19. Memorizing frequently used settings [Program function] Up to seven combinations of copy modes and other functions displayed on the operation panel can be registered as a single program using this function. 4 Use the M cursor or the N cursor key to select the program number
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 91
    (2) Using programmed settings to make copies 1 Press the Program key. Inch specifications Metric specifications Section 6 FUNCTIONS 3 Press the Enter key. The message display will return to the "Ready to copy." screen. Copying is now possible using the settings that were registered under that
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 92
    Section 6 FUNCTIONS 20. Confirming copy settings (Recall function) When you have selected the copy mode and other functions, etc., the content of the settings that you have made can be confirmed using this function. 1 Press the Program key. Inch specifications Metric specifications 2 Use the M
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 93
    Metric specifications NOTES • If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. • If "On" is selected under "› Rotate sort ON/OFF" on page 7-23 and the size of the finished copies
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 94
    panel. NOTES • If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. • This function will only work with 8 1/2" x 11" or 5 1/2" x 8 1/2" [A4, A5, B5 or B6] size paper. NOTES • To resume
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 95
    in a standby mode more than they are in actual operation, so power consumption in the standby mode occupies a large part of overall consumption. Having the copier turned OFF ( ) automatically after a certain amount of time reduces unnecessary power consumption in the standby mode or at night
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 96
    copying. When a department reaches its acceptable copy limit, the copier will not make any more copies under that department code. G Deleting department codes Perform this procedure when you want to delete registered department codes. 7-5 G Changing copy limits Perform this procedure when you
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 97
    to print out a list of the number of copies made under each department code. 7-10 G Turning copy management ON/OFF Perform this procedure when you want when the optional Printer Kit is installed in your copier. G Turning the printing error When printing management is turned ON, you can have
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 98
    Section 7 COPIER MANAGEMENT (2) Accessing the copy management procedures 1 Press the */Language key. The "Default key. 4 Use the numeric keys on the keypad to enter the 4-digit management PIN code "3000". Inch specifications Metric specifications NOTE It is possible for you to change the 4-digit
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 99
    Performing copy management procedures G Registering new department codes 1 Display the "Copy Management" screen. (See page 7-3.) 2 Use the M cursor or the N cursor key to select "x Management Setting" ["x COPY MGMT SETTING"]. Inch specifications Section 7 COPIER MANAGEMENT 7 Use the N cursor key to
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 100
    Section 7 COPIER MANAGEMENT 11 Use the M cursor key to select "z End" and then press the Enter key. The message display will return to the screen in step 2. Inch specifications 4 Use the M cursor or the N cursor key to select "c Delete Code" ["c CODE DELETE"]. Inch specifications Metric
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 101
    department code, repeat steps 6 through 8. 9 Press the Stop/Clear key. The message display will return to the screen in step 4. 10 Use the M cursor key to select "z End" and then press the Enter key. The message display will return to the screen in step 2. Inch specifications Section 7 COPIER
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 102
    Section 7 COPIER MANAGEMENT 7 Press the Enter key. 8 Use the numeric keys on the keypad to enter the new copy limit for that department code. The copy limit can be set to any 1 page increment between 1 and 999,999. Inch specifications Metric specifications 12 Use the M cursor key to select "z
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 103
    " is selected and press the Enter key. The message display will return to the screen in step 4. Inch specifications Section 7 COPIER MANAGEMENT G Printing out the department code list 1 Display the "Copy Management" screen. (See page 7-3.) NOTE Make sure that 11" x 8 1/2" or 8 1/2" x 11" [A4 or A4R
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 104
    Section 7 COPIER MANAGEMENT 6 Use the M cursor key to select "z End" and then press the Enter key. The message display will return to the screen in step 2. Inch specifications 3 Press the Enter key. The total number of copies made under all department codes as a whole will be displayed. Inch
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 105
    Feeder.) 2 Use the M cursor or the N cursor key to select "v Printer managemnt list" ["v PRINT MANAGEMENT LIST"]. Inch specifications Section 7 COPIER MANAGEMENT G Turning copy management ON/OFF 1 Display the "Copy Management" screen. (See page 7-3.) NOTE An indication whether copy management is
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 106
    COPIER MANAGEMENT 5 Press the Enter key. The display will return to the screen in step 2. 6 Use the M cursor key to select "z End" and then press the Enter key. • If you selected "z ON" in step 4, the department code enter your designated department code. Inch specifications Metric specifications
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 107
    all of the settings as desired in order to make the most effective use of your copier. Section 7 COPIER MANAGEMENT Default setting Description 1 Exposure mode Selects between auto exposure (page 4-3) and manual exposure (page 4-3) as the default copy exposure mode at the time power is turned on
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 108
    * No.3 and No.4 drawers can only be selected when the optional Paper Feeder is installed in your copier. Standard copiers 1 paper [SOURCE 1] - 4 paper [SOURCE 4] Duplex copiers 2 paper [SOURCE 2] - 4 paper [SOURCE 4] Standard copiers 1 paper [SOURCE 1] Duplex copiers 2 paper [SOURCE 2] 7-19 7-13
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 109
    be designated under "6 Color copy paper location" on page 7-29. Standard copiers 1 paper [SOURCE 1] - 4 paper [SOURCE 4] Duplex copiers 2 paper [SOURCE 2] - 4 paper [SOURCE 4] Standard copiers 1 paper [SOURCE 1] Duplex copiers 2 paper [SOURCE 2] 7-20 $ Copy limit Sets a limit to the number of
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 110
    black&white originals in the Auto Color Selection mode (page 4-1). ¤ Auto color adjustment Slight changes in color copying may take place if --- your color copier is used over a long period of time. If the color on the originals and that which appears on the copies begins to differ greatly
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 111
    SELECT SET ITEM"] screen will appear. Inch specifications Metric specifications Section 7 COPIER MANAGEMENT 5 Use the M cursor or the N cursor key to select It is possible for you to change the 4-digit management PIN code. (See "0 Management PIN code" on page 7-30.) 8 Press the Enter key. 9 Refer
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 112
    Section 7 COPIER MANAGEMENT 1 Exposure mode 1 Use the M cursor or the N cursor key to select either "z Auto" or "x Manual". Inch specifications Metric specifications 2 Press the Enter key. 2 Exposure steps 1 Press the M cursor or the N cursor key to select either "z 7 Steps" or "x 13 Steps". Inch
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 113
    cursor to the right to make copies darker, and to the left to make copies lighter when using the text&photo mode. Inch specifications Section 7 COPIER MANAGEMENT 7 Print original density 1 Press the O cursor or the P cursor key to adjust the exposure as desired. Move the cursor to the right to make
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 114
    Section 7 COPIER MANAGEMENT 9 Map original density 1 Press the O cursor or the P cursor key and white copying. * The "1 paper" ["SOURCE 1"] drawer is not available in duplex copiers. Inch specifications Metric specifications Metric specifications 2 Press the Enter key. 2 Press the Enter key. 7-
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 115
    that will be automatically selected for feeding paper in color copying. * The "1 paper" ["SOURCE 1"] drawer is not available in duplex copiers. Inch specifications Section 7 COPIER MANAGEMENT % Margin width 1 Press the O cursor or the P cursor key to select the default margin width. (The width can
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 116
    that contains the paper which will be fed in the insert sheet modes. * The "1 paper" ["SOURCE 1"] drawer is not available in duplex copiers. Inch specifications Metric specifications Metric specifications 2 Press the N cursor key to change to the width size setting. 3 Press the O cursor or the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 117
    N cursor key to select either "z Inner Eject" (copy storage table) or "x Side Eject" (copy eject tray). Inch specifications Metric specifications Section 7 COPIER MANAGEMENT ¤ Auto color adjustment 1 Make sure that there is 11" x 8 1/2" [A4] paper loaded in one of the drawers. 2 Use the M cursor
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 118
    Section 7 COPIER MANAGEMENT 5 Once print out is complete, set the printed color pattern on the platen. NOTES • Set the PG color pattern on the platen so that
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 119
    /OFF will be used or not. The auto shut-off function automatically turns the main switch OFF if no operation has been performed on the copier for a certain period of time. * If auto shut-off interferes with your copying operations, turn this function OFF. It is recommended that you try to
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 120
    before the auto shut-off function (page 6-48) engages and turns the copier OFF ( ). It is also possible to disable the auto shut-off function to set a longer time interval before auto shut-off engages if you use the copier frequently, and to a shorter time if it is used less frequently. * In
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 121
    code "6482". 3000 7-30 ! Silent mode The copier can be switched to a silent mode, which On / Off Off ON/OFF shuts down the motor inside the copier copies made. ----- 7-31 $ Counter report print Prints out reports on toner usage for each of the ----- out copy, printer and fax functions of
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 122
    Section 7 COPIER MANAGEMENT (4) Accessing the machine default settings 1 Press the */Language key. specifications Metric specifications NOTE It is possible for you to change the 4-digit management PIN code. (See "0 Management PIN code" on page 7-30.) 8 Press the Enter key. 9 Refer to and perform
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 123
    is loaded in one of the drawers. * If a Memory Copy Board is installed in your copier, make sure that 8 1/2" x 11" or 11" x 8 1/2" [A4 or A4R] size key to select either "z On" or "x Off". Inch specifications Section 7 COPIER MANAGEMENT 4 Special paper location 1 Use the M cursor or the N cursor
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 124
    Section 7 COPIER MANAGEMENT 5 APS for special paper ON/OFF 1 Use the M cursor or the N cursor paper will be loaded for color copying. * The "1 paper" ["SOURCE 1"] drawer is not available in duplex copiers. Inch specifications 2 Press the Enter key. 8 Auto shut-off time 1 Use the M cursor or the N
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 125
    and to the left to make the display lighter. Inch specifications Section 7 COPIER MANAGEMENT ! Silent mode ON/OFF 1 Use the M cursor or the N the Enter key. 0 Management PIN code 1 Use the numeric keys on the keypad to enter a new 4-digit management PIN code. Inch specifications 2 Press the Enter
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 126
    TYPE (1ST)"] drawer setting is not available in duplex copiers. Inch specifications Metric specifications Metric specifications 2 Use the size paper is loaded in one of the drawers. * If a Memory Copy Board is installed in your copier, make sure that 8 1/2" x 11" or 11" x 8 1/2" [A4 or A4R] size
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 127
    used in the message display. NOTE The available languages are as follows: Inch specification copiers: English, French ("Français"), Spanish ("Español") and Japanese (" ") Metric specification copiers: English, German ("DEUTSCH"), French ("FRANÇAIS"), Italian ("ITALIANO") and Spanish ("ESPAÑOL
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 128
    edge of the paper with the holes or perforations is facing away from the SRDF. G Names of parts 3 2 712 5 64 1 Original table (Set originals to be copied on this table.) 2 Original insert guides (Align these guides to fit the width of the originals to be copied.) 3 Left cover (Open this cover if an
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 129
    is LESS than the level indicator on inside of the rear insert guide. Also, DO NOT set originals outside the acceptable range as this other originals to misfeed. • To keep ejected originals from falling off the copier, open the ejection extension when using larger sized originals such as 8 1/2"
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 130
    that there are no originals remaining on the original eject table. If there are originals left on the eject table, they will fall off the copier when the SRDF is opened. G Auto selection mode If you use the auto selection mode without pressing the Paper Select key and specifying a desired paper
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 131
    sets as well. For more details, refer to the Operation Guide for the Document Finisher. (5) Casters These casters are for attaching to the bottom of your copier. CAUTION To prevent the possibility of accidents due to tilting the copier body, always turn the desk's stopper bolts until they make
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 132
    machine are counted on the key counter. (7) Printer Kit If the Printer Kit is installed in your copier, you can use the copier as a printer. For more details, refer to the Operation Guide for the Printer Kit. Inch specifications G Setting the Key Counter Insert the Key Counter securely into the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 133
    (9) Network Scanner Kit If the Network Scanner Kit is installed in your copier, you can use the copier as a scanner from multiple computers over your network. For more details, refer to the Operation Guide for the Network Scanner Kit. Section 8 OPTIONAL EQUIPMENT 8-6
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 134
    TROUBLESHOOTING duplex unit." "INSTALL DUPLEX UNIT." (Only in duplex copiers) The Duplex Unit is not inserted properly. First pull copy eject tray. -- "Drawer inoperable. Call for service." "PAPER DRAWER IS OUT OF ORDER. SELECT OTHER Stop/Clear key to delete the error message. Make sure the size of
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 135
    "READY TO COPY. ADD TONER. (KCMY)" (C = cyan, M = magenta, Y = yellow, K = black). "Add toner to resume copying. (KCMY)" The copier has run out of toner of the color indicated. Replace the 3-8 corresponding toner cartridge immediately (C = cyan, M = magenta, "ADD TONER TO RESUME COPYING. (KCMY
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 136
    TROUBLESHOOTING Message "Paper misfeed." "PAPER MISFEED." Procedure If paper misfeeds, the copier original. 9-14 "Duplex tray inoperable, call for service." "DUPLEX UNIT IS OUT OF ORDER. 1-SIDED COPYING Finisher is full. Refer to the Operation Guide for your Document Finisher and dispose of the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 137
    Section 9 TROUBLESHOOTING 2. If paper jams If a paper misfeed occurs, copying will stop. . Take sufficient care when working in this area, as there is a danger of electrical shock. CAUTION The copier's fixing unit is extremely hot. Take sufficient care when working in this area, as there is a danger
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 138
    Section 9 TROUBLESHOOTING (3) Removal procedures 1 Misfeed in a paper feed area G Misfeed in a drawer If " a procedure to remove the jammed paper. * If the optional Paper Feeder is installed in your copier and the jam has occurred in that unit, the misfeed location indicators indicated by the a in
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 139
    2 Remove the jammed paper without tearing it. * If the paper does happen to tear, remove any loose scraps from inside the copier. Section 9 TROUBLESHOOTING G Misfeed in the multi-bypass tray If "Paper misfeed in stack bypass. Remove paper." is displayed and the misfeed location indicator shown in
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 140
    Section 9 TROUBLESHOOTING 3 Open and then close the front cover. The misfeed message will Take sufficient care when working in this area, as there is a danger of electrical shock. CAUTION The copier's fixing unit is extremely hot. Take sufficient care when working in this area, as there is a danger
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 141
    well, remove the paper without tearing it. * If the paper does happen to tear, remove any loose scraps from inside the copier. Section 9 TROUBLESHOOTING 3 Misfeed in the transfer section If "Paper misfeed. Open Front Cover." is displayed and the misfeed location indicator shown in the illustration
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 142
    Section 9 TROUBLESHOOTING 3 Turn the green transfer unit release lever to the left until it towards you as far as it will go. 1 6 Replace the transfer unit in its original position in the copier. 5 Remove the jammed paper without tearing it. If the paper is difficult to remove at all, turn the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 143
    the paper conveyor in its original position in the copier. Section 9 TROUBLESHOOTING 1 Open the front cover. 9 Close the when working in this area, as there is a danger of electrical shock. CAUTION The copier's fixing unit is extremely hot. Take sufficient care when working in this area, as there
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 144
    Section 9 TROUBLESHOOTING 4 While holding the 2 green lock-levers (shown as 2 in ) to the inner cover and open that cover. 8 Replace the paper conveyor in its original position in the copier. 3 6 Remove the jammed paper without tearing it. If the paper is difficult to remove at all, turn
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 145
    table. Perform the following procedure to remove the jammed paper. Section 9 TROUBLESHOOTING 3 Open the left cover. 1 Remove all of the copies from the If the paper does happen to tear, remove any loose scraps from inside the copier. 2 If necessary, open the copy eject tray. NOTE If the paper is
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 146
    Section 9 TROUBLESHOOTING 6 Misfeed in the Duplex Unit (Only in duplex copiers) If "Paper misfeed. Open Duplex Unit Cover." 2 4 Close all open covers and replace the Duplex Unit in its original position in the copier. 2 Open the Duplex Unit cover (shown as 1 in the illustration) and remove the
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 147
    has misfed in the SRDF. In this case, the original set indicator will flash red. Perform the following procedure to remove the jammed original. Section 9 TROUBLESHOOTING 3 Open the left cover to the SRDF. * Be sure to hold the handle in the middle of the cover when opening it. 1 Remove all of
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 148
    Section 9 TROUBLESHOOTING 6 If there are any originals there, remove the jammed original without tearing it. * If the original shown in the illustration lights, a misfeed has occurred in the Document Finisher. Refer to the Operation Guide for the Document Finisher and remove the jammed paper. 9-15
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 149
    Section 9 TROUBLESHOOTING 3. If other trouble occurs If trouble occurs with your copier, carry out the applicable checkpoints and procedures indicated on the following pages. If the trouble persists, contact your service representative or authorized service center. Trouble Checkpoint Nothing
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 150
    Section 9 TROUBLESHOOTING Trouble The copies come out too dark. Checkpoint Is the copier in the auto exposure mode? Procedure In order to adjust the overall exposure level, perform the "Auto exposure adjustment" procedure. Reference page 7-17 Is the copier in the manual exposure mode? Adjust
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 151
    Trouble Checkpoint The copy image is skewed. Were the originals set correctly? Section 9 TROUBLESHOOTING Procedure When setting originals on the platen, align them securely with appropriate original size indicators. When setting originals in the optional DF, align the original insert guides
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 152
    dampened with alcohol or mild detergent. a * See "3. Cleaning the charger" on page 3-11 for the procedure to clean the interior portion of the copier. G Cleaning the platen Lift open the original cover. Wipe the platen with a soft cloth dampened with alcohol or mild detergent. * Never use thinner
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 153
    feeding from drawers (Standard copiers: 2 drawers, Duplex copiers: 1 drawer; each with a 500 sheet capacity [75 g/m2 - 90g/m2]) or manual feed from the multi-bypass available in inch specification copiers), Network Scanner Kit *: Standard equipment in duplex copiers (Specifications are subject to
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 154
    Appendix: Functions and settings combination chart This copier contains many different functions and settings, and adjustment Color balance adjustment One-touch image quality adjustment Gloss mode Auto exposure mode Manual exposure mode Eco mode Text&photo mode Map mode Printed photo mode Photo mode
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 155
    required in order to make duplex (2-sided) copies. *3: Only available in duplex copiers. 2-sided copy modes Page Insert separation sheet modes modes Layout modes Margin Border photo mode Map mode Text&photo mode Eco mode Manual exposure mode Auto exposure mode Gloss mode One-
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 156
    be attached to laser products marketed in the United States. On this copier, the label is on the right. 3. Optical unit When checking unit. 4. Maintenance For safety of the service personnel, follow the maintenance instructions in the other section of this manual. 5. Safety switch The power to
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 157
    * For best copy results and machine performance, we recommend that you use only KYOCERA MITA original supplies for your KYOCERA MITA copier.
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 158
    CAUTION! The power plug is the main isolation device! Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source. ATTENTION ! Le débranchement de la fiche secteur est le seul moyen de mettre l'appareil hors tension. Les
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 159
    comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 160
    A1
  • Kyocera KM-C830D | KM-C830 Operation Guide Rev-1B - Page 161
    75038-5299 TEL : (972) 550-8987 FAX : (972) 570-4704 Dallas Parts Distribution Center & National Training Center: 2825 West Story Road, Irving, Texas 75038-5299 TEL : (972) 659-0055 FAX : (972) 570-5816 KYOCERA MITA CANADA, LTD. 6120 Kestrel Road, Mississauga, Ontario L5T 1S8, Canada TEL : (905
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
Operation Guide
Please read the Operation Guide before using the copier.
Keep it close to the copier for easy reference.
* The illustration above shows the copier with the optional original cover installed.