LG DLG1502W Owners Manual - English Spanish - Page 27

Installation Test Duct check

Get LG DLG1502W PDF manuals and user guides View all LG DLG1502W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

ENGLISH INSTALLATION INSTRUCTIONS 27 Installation Test (Duct check) Once you have completed the installation of the dryer, use this test to make sure the condition of the exhaust system is adequate for proper operation of the dryer. This test should be performed to alert you to any serious problems in the exhaust system of your home. • Your dryer features Flow Sense™, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use. NOTE The dryer should be cool before starting this test. If the dryer was warmed up during installation, run the AIR DRY cycle for a few minutes to reduce the interior temperature. To activate the installation test: 1. Remove the literature, and then close the door. Do not load anything in the drum for this test, as in may affect the accuracy of the results. 4. Check the display for results. During the three minute test cycle, monitor the Flow Sense™ display on the control panel. If no bars are displayed, when the cycle ends, the exhaust system is adequate. If the exhaust system is severely restricted, the display will show four bars. Other problems may also be shown with error codes. Refer to the next page for error code details and solutions. NO BARS: OK FOUR BARS: RESTRICTED Four bars indicates that the exhaust system is severely restricted. Have the system checked immediately, as performance will be poor. 5. End of cycle. At the end of the test cycle, will display. The test cycle will end and the dryer will shut off automatically after a short delay. 2. Press and hold the Temp. and Signal buttons and then press the POWER button. This button sequence activates the installation test. The code will display if the activation is successful. 3. Press START/PAUSE button. The dryer will start the test, which will last about two minutes. The heat will be turned on and the temperatures in the drum will be measured. MFL67731056_en_150715.indd 27 2015.7.15 3:38:55 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
27
ENGLISH
Installation Test (Duct check)
Once you have completed the installation of the dryer,
use this test to make sure the condition of the exhaust
system is adequate for proper operation of the dryer.
This test should be performed to alert you to any serious
problems in the exhaust system of your home.
• Your dryer features Flow Sense™, an innovative sensing
system that automatically detects blockages and
restrictions in dryer ductwork. Keeping ductwork clean
of lint buildup and free of restrictions allows clothes to
dry faster and reduces energy use.
To activate the installation test:
1.
Remove the literature, and then close the door
.
Do not load anything in the drum for this test, as in
may affect the accuracy of the results.
2.
Press and hold the Temp. and Signal buttons and
then press the POWER button.
This button sequence activates the installation test.
The code
will display if the activation is
successful.
3.
Press START/PAUSE button.
The dryer will start the test, which will last about
two minutes. The heat will be turned on and the
temperatures in the drum will be measured.
4.
Check the display for results.
During the three minute test cycle, monitor the
Flow Sense™ display on the control panel. If no bars
are displayed, when the cycle ends, the exhaust
system is adequate. If the exhaust system is severely
restricted, the display will show four bars. Other
problems may also be shown with error codes. Refer
to the next page for error code details and solutions.
Four bars indicates that the exhaust system is severely
restricted. Have the system checked immediately, as
performance will be poor.
5.
End of cycle.
At the end of the test cycle,
will display.
The test cycle will end and the dryer will shut off
automatically after a short delay.
NO BARS:
OK
FOUR BARS:
RESTRICTED
NOTE
The dryer should be cool before starting this test. If
the dryer was warmed up during installation, run the
AIR DRY cycle for a few minutes to reduce the interior
temperature.
INSTALLATION INSTRUCTIONS
MFL67731056_en_150715.indd
27
2015.7.15
3:38:55 PM