LG DLGX3886C Owner's Manual - Page 32

End Of Cycle

Get LG DLGX3886C PDF manuals and user guides View all LG DLGX3886C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

THE LCD DISPLAY (cont.) H FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR The FLOW SENSE™ duct blockage sensing system detects and alerts you to blockages in the ductwork that reduce exhaust flow from the dryer. This improves operating efficiency and helps minimize service calls, saving you money. If no bars are shown in the display, the ductwork is free from blockages. If two bars in the display are lighted, examine the dryer exhaust system for lint build up or other restrictions, including damage, excess length, foreign objects, etc. See note below. If all bars are lit, the dryer ductwork has a blockage that needs to be removed immediately. NOTE: If the duct has been checked and cleaned and two bars are still displayed after several cycles, then there is some restriction in the duct due to length, condition, etc. In this case, no further action is necessary and the dryer can be used normally. However, drying times may be increased and there may be some reduction in operating efficiency • 2 bars are displayed In the LCD screen. END OF CYCLE 1. Possible causes • Ductwork is slightly too long or has too many turns/restrictions. • Partial blockage of the ductwork due to lint buildup. 2. Solutions • Install a shorter or straighter duct run. See the Installation Instructions. • Ductwork should be checked/cleaned soon. Dryer can be used in this condition, but drying times may be longer. • If END OF CYCLE is displayed after the end of cycle, it will be off in 4 minutes. If POWER button is pressed or the door is opened, power will be off immediately. • 4 bars are displayed In the LCD screen. NEED FLOW CHECK THE DUCTWORK HAS A BLOCKAGE THAT NEEDS TO BE REMOVED IMMEDIATELY. 1. Possible causes • Ductwork is too long or has too many turns/ restrictions. • Significant blockage of the ductwork due to lint buildup or debris. 2. Solutions • Install a shorter or straighter duct run. See the Installation Instructions. • Ductwork should be checked/cleaned soon. Dryer can be used in this condition, but drying times may be longer. • If NEED FLOW CHECK is displayed after the end of cycle, it will be off in 2 hours. If POWER button is pressed or the door is opened, power will be off immediately. 32 MFL62512806_EN_0208.indd 32 2010.2.8 2:7:42 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
H
FLOW SENSE™ DUCT BLOCKAGE
SENSING SYSTEM INDICATOR
The FLOW SENSE™ duct blockage sensing
system detects and alerts you to blockages
in the ductwork that reduce exhaust flow
from the dryer. This improves operating
efficiency and helps minimize service calls,
saving you money.
THE LCD DISPLAY
(cont.)
THE DUCTWORK HAS
A BLOCKAGE THAT NEEDS
TO BE REMOVED
IMMEDIATELY.
NEED FLOW CHECK
If no bars are shown in the
display, the ductwork is free from
blockages.
If two bars in the display are
lighted, examine the dryer
exhaust system for lint build up
or other restrictions, including
damage, excess length, foreign
objects, etc. See note below.
If all bars are lit, the dryer
ductwork has a blockage
that needs to be removed
immediately.
• 2 bars are displayed In the LCD screen.
• Ductwork is slightly too long or has too
many turns/restrictions.
• Partial blockage of the
ductwork due to lint
buildup.
1. Possible causes
• Install a shorter or straighter duct run. See
the
Installation Instructions.
• Ductwork should be checked/cleaned soon.
Dryer can be used in this condition, but
drying
times may be longer.
• If END OF CYCLE is displayed after the end
of cycle, it will be off in 4 minutes. If POWER
button is pressed or the door is opened,
power will be off immediately.
2. Solutions
NOTE:
If the duct has been checked and
cleaned and two bars are still displayed after
several cycles, then there is some restriction
in the duct due to length, condition, etc.
In
this case, no further action is necessary and
the dryer can be used normally.
However,
drying times may be increased and there may
be some reduction in operating efficiency
• 4 bars are displayed In the LCD screen.
• Ductwork is too long or has too many turns/
restrictions.
• Significant blockage of the ductwork due to
lint buildup or debris.
1. Possible causes
• Install a shorter or straighter duct run. See
the
Installation Instructions.
• Ductwork should be checked/cleaned soon.
Dryer can be used in this condition, but
drying times may be longer.
• If NEED FLOW CHECK is displayed after
the end of cycle, it will be off in 2 hours. If
POWER button is pressed or the door is
opened, power will be off immediately.
2. Solutions
END OF CYCLE
32
MFL62512806_EN_0208.indd
32
2010.2.8
2:7:42 PM