LiftMaster 1355 1355 Manual - Page 33
Care of Your Opener, Having a Problem? - review
View all LiftMaster 1355 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 33 highlights
Care of Your Opener Having a Problem? LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some readjustments, particularly during the first year of operation. LIMIT CONTROLS (Left side panel) Pages 28 and 29 refer to the limit and force adjustments. 9 1 9 1 Only a screwdriver is required. Follow the instructions carefully. 7 3 5 KG 7 3 5 KG Repeat the safety reverse test Open Force Close Force (page 30) after any adjustment FORCE CONTROLS of limits or force. (Back panel) MAINTENANCE SCHEDULE Once a Month • Manually operate door. If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens & closes fully. Adjust limits and/or force if necessary. (See pages 28 and 29.) • Repeat the safety reverse test. Make any necessary adjustments. (See page 30.) Twice a Year • Check chain tension. Disconnect trolley first. Adjust if necessary (see page 11). Once a Year • Oil door rollers, bearings and hinges. The opener does not require additional lubrication. Do not grease the door tracks. THE REMOTE CONTROL BATTERY WARNING To prevent possible SERIOUS INJURY or DEATH: CAUTION • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. The lithium battery should produce power for up to 5 years. To replace battery, use the visor clip or screwdriver blade to pry open the case as shown. Insert battery positive side up. Dispose of old battery properly. Battery positive side up (+) NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1. The opener doesn't operate from either the Door Control or the remote control: • Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) • Have you disabled all door locks? Review installation instruction warnings on page 11. • Is there a build-up of ice or snow under the door? The door may be frozen to the ground. Remove any restriction. • The garage door spring may be broken. Have it replaced. • Repeated operation may have tripped the overload protector in the motor. Wait 15 minutes and try again. 2. Opener operates from the remote, but not from the Door Control: • Is the door control lit? If not, remove the bell wire from the motor unit terminals. Short the red and white terminals by touching both terminals at the same time with a piece of wire. If the opener runs, check for a faulty wire connection at the door control, a short under the staples, or a broken wire. • Are the wiring connections correct? Review Installation Step 6, page 18. 3. The door operates from the Door Control, but not from the remote control: • Is the door push bar flashing? If your model has the Lock feature, make sure it is off. • Program the opener to match the remote control code. (Refer to instructions on the motor unit WARNING panel.) Repeat with all remotes. 4. The remote control has short range: • Change the location of the remote control in your car. WARNING • Check to be sure the antenna on the side or back panel of motor unit extends fully downward. • Some installations may have shorter range due to a metal door, foil backed insulation, or metal garage siding. 5. Opener noise is disturbing in living quarters of home: • If operational noise is a problem because of proximity of the opener to the living quarters, the Vibration Isolator Kit 89LM can be installed. This kit was designed to minimize vibration to the house and is easy to install. 33