Home » LiftMaster Manuals » Garage Door Openers » LiftMaster 1355 » Manual Viewer

LiftMaster 1355 1355 Manual - Page 37

Repair Parts - owners manual

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

REPAIR PARTS Rail Assembly Parts 5 1 3 4 2 KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A4813 Chain pulley bracket 6 3 41A3489 Complete trolley assembly 4 1707LM One-piece rail 5 41D3484 Full chain assembly 6 83A11 Rail grease Installation Parts 1 5 NOTICE 12 3 6 2 7 CEILING MOUNT ONLY UP 8 10 9 11 4 KEY PART NO. NO. DESCRIPTION 1 41A4166 Door control button 2 371LM Single-button remote control 3 10A20 3V2032 Lithium battery 4 29B137 Transmitter visor clip 5 41A2828 Emergency release rope & handle assembly 6 41B4494-1 2-conductor bell wire - white & white/red 7 41A4353 Header bracket w/clevis pin & fastener 8 41A5047 Door bracket w/clevis pin & fastener 9 41A5034 Safety sensor kit (receiving and sending eyes) with 3' (.9 m) 2-conductor bell wire attached 10 178B34 Straight door arm section 11 178B35 Curved door arm section 12 41A5266-1 Safety sensor brackets (2) Not shown 41A2770-6 Installation hardware bag (see page 7). 114A3072 Owner's manual 114A3072SP Owner's manual - Spanish 37

Section	Page
ENGLISH	1
TABLE OF CONTENTS	2
INTRODUCTION	2
Safety Symbol and Signal Word Review	2
Preparing your garage door	3
Tools needed	3
Planning	4
ONE-PIECE DOOR INSTALLATIONS	5
Carton Inventory	6
Hardware Inventory	7
ASSEMBLY	8
STEP 1 Fasten the Rail to the Motor Unit	8
STEP 2 Attach the Chain to the Sprocket and Install the Sprocket Cover	8
STEP 3 Fasten the Rail to the Motor Unit	9
STEP 4 Attach the Chain Spreader and Re-install the Chain	10
STEP 5 Tighten the Chain	11
INSTALLATION	11
STEP 1 Determine the Header Bracket Location	12
ONE-PIECE DOOR WITHOUT TRACK	13
STEP 2 Install the Header Bracket	14
STEP 3 Attach the Rail to the Header Bracket	15
STEP 4 Position the Opener	16
STEP 5 Hang the Opener	17
STEP 6 Install the Door Control	18
STEP 7 Install the Light and Lens	19
STEP 8 Attach the Emergency Release Rope and Handle	19
STEP 9 Electrical Requirements	20
STEP 10 Install The Protector System®	21
INSTALLING THE BRACKETS	22
MOUNTING AND WIRING THE SAFETY REVERSING SENSORS	23
STEP 11 Fasten the Door Bracket	24
ONE-PIECE DOORS	25
STEP 12 Connect Door Arm to Trolley	26
ALL ONE-PIECE DOORS	27
ADJUSTMENT	28
STEP 1 Adjust the UP and DOWN Travel Limits	28
STEP 2 Adjust the Force	29
STEP 3 Test the Safety Reversal System	30
STEP 4 Test the Protector System®	30
OPERATION	31
Using Your Garage Door Opener	31
Using the Wall-Mounted Door Control	32
To Open the Door Manually	32
Care of Your Opener	33
Having a Problem?	33
PROGRAMMING	35
To Add or Reprogram an Additional Hand-held Remote Control	35
To Erase All Codes From Motor Unit Memory	35
3-Button Remotes	35
To Add, Reprogram or Change a Keyless Entry PIN	36
REPAIR PARTS	37
Rail Assembly Parts	37
Installation Parts	37
Motor Unit Assembly Parts	38
ACCESSORIES	39
WARRANTY	40