Mackie 1402-VLZ Pro Owner's Manual - Page 16
Phones, ALT 3-4 Output, Control Room, Aux Send 1 & 2, the headphone amp is
View all Mackie 1402-VLZ Pro manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
MIC 1 XDR MIC PRE MIC 2 XDR MIC PRE MIC 3 XDR MIC PRE MIC 4 XDR MIC PRE MIC 5 XDR MIC PRE MIC 6 XDR MIC PRE LEFT/MONO RIGHT 1 ALL BAL/UNBAL 1 TAPE TAPE INPUT OUTPUT L 2 2 R BAL/UNBAL L R BAL OR UNBAL LINE IN 1 LOW CUT 75 Hz 18dB/OCT U M-I1C0dGBAVIN BAL OR UNBAL LINE IN 2 LOW CUT 75 Hz 18dB/OCT U M-I1C0dGBAVIN BAL OR UNBAL LINE IN 3 LOW CUT 75 Hz 18dB/OCT U M-I1C0dGBAVIN BAL OR UNBAL LINE IN 4 LOW CUT 75 Hz 18dB/OCT U M-I1C0dGBAVIN BAL OR UNBAL LINE IN 5 LOW CUT 75 Hz 18dB/OCT U M-I1C0dGBAVIN BAL OR UNBAL LINE IN 6 LOW CUT 75 Hz 18dB/OCT U M-I1C0dGBAVIN STEREO AUX RETURN MONO L BAL OR UNBAL R AUX SEND MONO L BAL OR UNBAL R MONO L BAL OR UNBAL R MAIN OUT MONO L BAL OR UNBAL R 0 60 +15dB -45dB TRIM 0 60 +15dB -45dB TRIM 0 60 +15dB -45dB TRIM 0 60 +15dB -45dB TRIM 0 60 +15dB -45dB TRIM 0 60 +15dB -45dB TRIM LEVEL +4 -10 LINE IN 7-8 LEVEL +4 -10 LINE IN 9-10 LEVEL +4 -10 LINE IN 11-12 LEVEL +4 -10 LINE IN 13-14 PHONES The 1402-VLZ PRO's stereo PHONES jack will drive any standard headphone to very loud levels. Walkperson-type phones can also be used with an appropriate adapter. To learn how signals are routed to these outputs: . If you're wiring your own cable for the PHONES output, follow standard conventions: RING SLEEVE SLEEVE RIGHT LEFT TIP RIGHT LEFT Tip = Left channel SLEEVE Ring = Right channel Sleeve = Common ground WARNING: When we say the headphone amp is loud, we're not kidding. It can cause permanent ear damage. Even intermediate levels may be painfully loud with some earphones. BE CAREFUL! Always turn the CTL ROOM/SUBMIX fader all the way down before connecting headphones. Keep it down until you've put the phones on. Then turn it up slowly. Why? "Engineers who fry their ears find themselves with short careers." ALT 3-4 OUTPUT These 1⁄4" jacks are balanced outputs capable of delivering 22dBu into a balanced or unbalanced load. To learn how signals are routed to these outputs: . To wire your own cables: . CONTROL ROOM These 1⁄4" jacks are balanced outputs capable of delivering 22dBu into a 600 ohm balanced or unbalanced load. To learn how signals are routed to these outputs: . To wire your own cables: . AUX SEND 1&2 These 1⁄4" jacks are also balanced outputs capable of delivering 22dBu into a 600 ohm balanced or unbalanced load. To learn how signals are routed to these outputs: . To wire your own cables: . 16