Marantz SR5001 Marantz AV Receiver IR Remote Code List - Page 19
Learn Mode, Learning Procedure, Erasing Programmed Codes, Returning To Initial Settings
View all Marantz SR5001 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
ENGLISH LEARN MODE This remote control is capable of learning and storing codes used by other remote controls that you already own. For codes which are not learned, the remote control will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer's AV equipment which is set by the customer. The receiver sensor for the remote control signals is located at the top of the remote control. Notes: • This remote control is capable to learn around 60 codes. • When the batteries are getting weak , the learing procedure is not successful. LEARNING PROCEDURE 1. Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 2 inches (0.05 m). 0.05 m SYSTEMRCR5E5M00OSTRE CONTROLLER 2. Press and hold down the SET and MENU buttons until LEARN indicator blinks. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 MULTI/ CAT M-SPKR INFO MENU ENTER 3. Select the SOURCE button to select the SOURCE. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP REMOTE CONTROLLER RC5001SR 4. Select the button to be learned. • LEARN indicator lights up. l/ SLEEP DISPLAY P.DIRECT SURROUND AUTO 1 CS 4 2 EX/ES 5 LIP SYNC/ dts INPUT 3 VIRTUAL T.MODE 6 5. Press and hold the button of the original remote controller to learn until the SEND indicator blinks twice. • When the SEND indicator blinks once, repeat this step. • When the memory of the RC5001SR is full, the LEARN and SEND indicators blink once. If you want to learn the code, you should erase other learned button. 6. Repeat steps 4 and 5 to learn other buttons in same SOURCE. 7. Repeat steps 3 to 6 to learn other SOURCE. 8. When you have finished programming the remote controller, press the SET button, then LEARN indicator stops blinking and exits from the LEARN mode. LEARN SEND SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO LIP SYNC/ dts INPUT Notes: • When the SEND indicator blinks once again, the transmitting code is unavailable for RC5001SR, or the transmitting signal is intercepted by noise. • If no buttons are pressed for approximately 1 minutes while in the LEARN mode, the remote controller automatically exits from the LEARN mode. ERASING PROGRAMMED CODES (RETURNING TO INITIAL SETTINGS) Codes can be erased in three ways: by buttons, sources, and by all memory contents. Erasing the code by buttons 1. Press and hold down the SET and MENU buttons until LEARN indicator blinks. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 MULTI/ CAT M-SPKR INFO MENU ENTER 2. Select the SOURCE button to select the button to be erased. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP REMOTE CONTROLLER RC5001SR 3. Press and hold down the SLEEP button and press the learned button twice to be erased. • SEND indicator blinks twice and the mode returns to LEARN mode. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 4. To return the NORMAL mode, press the SET button. Erasing the code by SOURCE 1. Press and hold down the SET and MENU buttons until LEARN indicator blinks. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 MULTI/ CAT M-SPKR INFO MENU ENTER 2. Press and hold down the SLEEP button and press the learned SOURCE button twice to be erased. • LEARN indicator lights. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 CH-SEL V-OFF ATT. BASS TV DVD TREBLE VCR DSS TUNER CD CDR MD TAPE AUX1 AUX2 AMP 3. Press ENTER button to continue erasing. • The SEND indicator blinks twice and the mode returns to LEARN mode. • To cancel the erasing operation, do not press ENTER button and simply touch any other button. INFO MENU T.TONE /SET UP ENTER EXIT 4. To return the NORMAL mode, press the SET button. Erasing the all SOURCES 1. Press and hold down the SET and MENU buttons until LEARN indicator blinks. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 MULTI/ CAT M-SPKR INFO MENU ENTER 2. Press and hold down the SLEEP button and press POWER ON and POWER OFF button. • LEARN indicator lights. SOURCE l/ SET SLEEP DISPLAY OFF ON P.DIRECT SURROUND AUTO 12 LIP SYNC/ dts INPUT 3 3. Press ENTER button to continue erasing. • The SEND indicator blinks twice and the mode returns to LEARN mode. • To cancel the erasing operation, do not press ENTER button and simply touch any other button. INFO MENU T.TONE /SET UP ENTER EXIT 4. To return the NORMAL mode, press the SET button. Note: Erasing codes will return to the factory preset code, or there will leave empty if the button has no factory preset code. 16