Marantz SR5001 Marantz AV Receiver IR Remote Code List - Page 31

ENGLISH VIDEO CONVERT: Select the VIDEO CONVERT function to enable or disable with the 1 or 2 cursor buttons. (Video cable connection: Refer to page 19) 3-1 VIDEO CONVERT TV : ON DVD : ON VCR1 : ON DSS : ON AUX1 : ON MAIN RETURN EXIT After you complete this portion of the set up, move the cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. HDMI AUDIO: This setting determines whether to playback audio input to the HDMI jacks through the SR4001/ SR5001 or output it through the receiver to a TV or projector. ENABLE: The audio input to the HDMI jacks can be played back by this receiver. In such case, audio signals are not output to the TV or projector. THROUGH: The audio input to the HDMI jacks is not output from the speaker terminals of the SR4001/SR5001. Audio data is output directly to the TV or projector. This setting is used to listen to audio on a multi channel TV, etc. DC TRIGGER: Select "DC TRIG SETUP" in the SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 3-2 DC TIRGGER SETUP DC TRIG DISABLE TV : DVD : VCR1 : DSS : AUX1 : CD : TAPE : CD-R : AUX2 : TUNER: 7.1CH: MAIN RETURN EXIT You can select MAIN ROOM, MULTI ROOM, REMOTE or DISABLE by pressing 1 or 2 cursor buttons. Notes: • REMOTE is available for the external control. The RC5001SR cannot operate this function. • To select desired input source , press 3 or 4 cursor button. • To set ON or OFF, press 1 or 2 cursor button. • After you complete this portion of the set up, move the cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. 4 SURROUND 4 SURROUND SURR.MODE :AUTO HT-EQ :OFF LFE LEVEL : MAIN EXIT 1. Select "SURROUND" in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To select a desired content , press the 3 or 4 cursor buttons. SURR.MODE: Select the desired surround mode with the 1 or 2 cursor buttons. HT-EQ: Select to active the HT-EQ with the 1 or 2 cursor buttons. The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because film soundtracks were designed to be played back in large movie theater environments. Activating the HT-EQ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance. The HT-EQ feature is available except in the following modes. • 7.1 CH INPUT • PURE-DIRECT • When VIRTUAL is set for the surround mode LFE LEVEL: Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select 0 dB, -10 dB or OFF with the 1 or 2 cursor buttons. After you complete this portion of the set up, move the cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. 5 PL II (PRO LOGIC II) MUSIC PARAMETER Pro Logic II-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs. In this mode, SR4001/SR5001 includes three controls to fine-tune the soundfield as follows. 5 PL II MUSIC PARAMETER PARAMETER : DEFAULT PANORAMAA : OFF DIMENSION : 3 CENTER WIDTH : 3 MAIN EXIT Select "PL II MUSIC" in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. PARAMETER: Select "DEFAULT" or "CUSTOM" with the 1 or 2 cursor buttons. If you select "CUSTOM", you can adjust three parameters as listed below. PANORAMA: Select the Panorama mode On or Off with the 1 or 2 cursor buttons. Panorama wraps the sound of the front left and right speakers around you, for an exciting perspective. DIMENSION: Set the Dimension level between +3 and -3 level in 1 level intervals with the 1 or 2 cursor buttons. Adjust the soundfield either towards the front or towards the rear. This can be useful to help achieve a more suitable balance from all the speakers with certain recordings. CENTER WIDTH: Set the Center width level between 0 and 7 in 1 level intervals with the 1 or 2 cursor buttons. Center Width allows you to gradually spread the center channel sound into the front left and right speakers. At its widest setting, all the sound from the center is mixed into the left and right. This control may help achieve a more spacious sound or a better blend for the front image. If "NONE" was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. 6 CS II (CIRCLE SURROUND II) PARAMETER 6 CS II PARAMETER TRUBASS SRS DIALOG : 0 : 0 MAIN EXIT 1. Select "CS II" in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button. 2. To Select desired contents as below, press the 3 or 4 cursor buttons. TRUBASS: Set the TRUBASS level between 0 and 6 level in 1 level interval with the 1 or 2 cursor buttons. TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects. SRS DIALOG: Set the SRS DIALOG level between 0 and 6 in 1 level intervals with the 1 or 2 cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say. If "NONE" was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear. After you complete this portion of the set up, move cursor to "MAIN" with the 3 or 4 cursor buttons and press the ENTER button. 28