Marantz SR5600 SR5600 User Manual - Page 17

ENGLISH ADVANCED CONNECTING CONNECTING THE REMOTE CONTROL JACKS DVD AUDIO PLAYER or SACD MULTI CHANNEL PLAYER CENTER L R FRONT SURR. SURR. SUB BACK WOOFER RL RL RL RL RLRL INPUT-1 CB/PB COMPONENT VIDEO CR/PR INPUT-2 Y CB/PB CR/PR MONITOR OUT Y CB/PB CR/PR S-VIDEO R VCR1 DSS/VCR2 MONITOR TV DVD IN OUT IN OUT OUT RC-5 MULTI RC L IN C TAPE OUT R CDR/MD MULTI L SL SBL C PRE OUT SR SL SBR SBL SW C 7.1CH IN IN OUT IN OUT OUT R SR SBR SW AUDIO (AUX2) LR LRLR RL RL RL CENTER L R FRONT MODEL NO. SR5600 SURR. SURR. BACK SUB WOOFER POWER AMPLIFER Subwoofer Front Center Front Left Right Surround Left Surround Right ANTENNA COMPONENT VIDEO INPUT-1 Y CB/PB CR/PR INPUT-2 Y CB/PB CR/PR MONITOR OUT Y CB/PB CR/PR FM (75Ω) GND AM VIDEO TV DVD VCR1 IN OUT DSS/VCR2 MONITOR IN OUT OUT S-VIDEO TV DVD VCR1 IN OUT DSS/VCR2 MONITOR IN OUT OUT DIGITAL IN DIGITAL OUT 3 4 COAX. RS-232C RC-5 MULTI RC IN L SL 1 2 TV L DVD OPT. VCR1 DSS/VCR2 CD TAPE OUT R SR CDR/MD MULTI L SL R IN OUT IN OUT IN OUT IN OUT OUT R SR AUDIO (AUX2) SBL SBR SBL SBR C PRE OUT SW C 7.1CH IN SW 2 MODEL NO. SR5600 RC OUT OPTION REMOTE CONTROL IN OUT 1 CD RECORDER EXTERNAL INTERNAL REMOTE CONTROL IN OUT MD DECK EXTERNAL INTERNAL REMOTE CONTROL IN OUT CD PLAYER EXTERNAL INTERNAL CONNECTING MULTI CHANNEL AUDIO SOURCE The 7.1CH INPUT jacks are for multichannel audio source such as a SACD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 28. 14 Surround Back Left Surround Back Right CONNECTING AN EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifiers. Be sure to connect each speaker to the corresponding external power amplifier. q You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the SR5600, be sure to always disable operation of the infrared sensor on the main unit by using the following procedure. 1. Hold down the MULTI button and MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the or cursor button to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled. Note: • Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE".