Marantz SR5600 SR5600 User Manual - Page 32
Aux2 Input, Lip.sync, Listening To The Tuner - receiver manual
View all Marantz SR5600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 32 highlights
ENGLISH 1. Select a desired Video source to decide the routed video signal to the Monitor Outputs . 2. Press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote to switch the 7.1 channel input. 3. If it is necessary to adjust the output level of each channel, press the CH.SEL button on the remote. Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between -10 to +10 dB. The subwoofer can be adjusted between -15 and +10 dB. These adjustments result will be stored to 7.1 CH. INPUT memory. 4. Adjust the main volume with the MAIN VOLUME knob or the VOL buttons on the remote. To cancel the 7.1 CH. INPUT setting, press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote. Notes: • When the 7.1 CH. Input is in use, you may not select a surround mode, as the external decoder determines processing. • In addition, there is no signal at the record outputs when the 7.1 CH. Input is in use. AUX2 INPUT If you don't need to connect 7.1 Ch. input terminals with multi channel decoder, L(front left) and R (front right) inputs terminals are available as AUX2 input. In this case, You can connect additional audio source to AUX2 as other audio input terminals. AV SURROUND RECEIVER SR5600 INPUT SELECTOR DISP MULTI AUTO SLEEP AUTO SURR MULTI STANDBY POWER ON / STANDBY M. SPEAKER B PHONES SURROUND MODE PURE DIRECT SIMP SET AUTO HT-EQ MEN LIP.SYNC Depending on the image device (TV, monitor, projector, etc.) connected to the SR5600, a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the SR5600 to correct the time lag between the sound and image. It can be operated with the "LIP.SYNC" and and cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag. Note: • The LIP.SYSNC feature turns OFF (0 ms) in the PURE DIRECT mode. When the PURE DIRECT mode is deactivated, the set value of the LIP.SYSNC feature is automatically restored. BASIC OPERATION (TUNER) LISTENING TO THE TUNER Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country's standard is 9 kHz step, Press TUNER button on the remote more than 6 seconds. Scan step will change. Note: • Preset memory for the tuner will clear by changing this setup. AUTO TUNING 2. 1. 1. DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MTX 6.1 EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR ND PURE DIRECT SIMPLE SETUP HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN M 2. TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. CLEAR MEMO A/D P.SCAN/V OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT INPUT/DISC+ AUDIO SUB-T/ATT PTY (Using the SR5600) 1. To select tuner and desired band (FM or AM), press the BAND button on the front panel. 2. Press the or cursor buttons on the front panel for more than 1 second to start the auto tuning function. 3. Automatic searching begins then stops when a station is tuned in. (Using the remote control unit) 1. To select tuner and desired band (FM or AM), press the TUNER button twice within in two seconds on the remote. 2. Press the 5 or 6 for more than 1 second on the remote. 3. Automatic searching begins then stops when a station is tuned in. If tuning does not stop at the desired station, use to the "Manual tuning" operation. MANUAL TUNING 2. 1. 1. DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MT X 6.1 EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR ND PURE DIRECT SIMPLE SETUP HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE DOWN M 2. TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. CLEAR MEMO A/D P.SCAN/V OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT INPUT/DISC+ AUDIO SUB-T/ATT PTY (Using the SR5600) 1. To select tuner and desired band (FM or AM), press the BAND button on the front panel 2. Press the or cursor buttons on the front panel to select the desired station. (Using the remote control unit) 1. To select tuner and desired band (FM or AM), press the TUNER button twice within in two seconds on the remote. 2. Press the 5 or 6 on the remote to tune in the desired station. DIRECT FREQUENCY CALL 1. 1. 2. 3. 4. POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. OSD MENU 3. 2. PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO DTS 2 3 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT INPUT/DISC+ AUDIO SUB-T/ATT PTY CH.SEL LIP.SYNC SYSTEM REMOTE CONTROLLER To select tuner and desired band (FM or AM), press the TUNER button twice within two seconds on the remote. Press the F.DIRECT on the remote, display will show "FREQ - - - -". Input your desired station's frequency with the numeric buttons on the remote. The desired station will automatically be tuned. 29