Marantz SR5600 SR5600 User Manual - Page 9
Rear Panel
View all Marantz SR5600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
ENGLISH REAR PANEL q w er ty ui ANTENNA COMPONENT VIDEO INPUT-1 Y CB/PB CR/PR INPUT-2 Y CB/PB CR/PR MONITOR OUT Y CB/PB CR/PR FM (75Ω) GND AM VIDEO TV DVD VCR1 IN OUT DSS/VCR2 MONITOR IN OUT OUT S-VIDEO TV DVD VCR1 IN OUT DSS/VCR2 MONITOR IN OUT OUT DIGITAL IN DIGITAL OUT 3 4 COAX. RS-232C RC-5 MULTI RC IN L SL 1 2 TV L DVD OPT. VCR1 DSS/VCR2 CD TAPE OUT R CDR/MD MULTI L SR SL R IN OUT IN OUT IN OUT IN OUT OUT R SR AUDIO (AUX2) SBL SBR SBL SBR C PRE OUT SW C 7.1CH IN SW MODEL NO. SR5600 AC IN SWITCHED UNSWITCHED 1A 120W MAX 1A 120W MAX AC OUTLETS 120V 60HZ R L R L R L FRONT CENTER SURROUND SPEAKER SYSTEMS : MINIMUM 6 OHMS SURROUND BACK M.SPEAKER B !6 !5 !4 !3 !2 !1 !0 o q VIDEO IN/OUT (TV, DVD, VCR1, DSS/VCR2) These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video configurations. Connect VCRs, DVD players, and other video components to the video inputs. The 2 video output channels can be used to be connected to video tape recorders for making recordings. The input signals of video and S-video are converted each other, and each of the converted video signals can be output. w FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked "AM" and "GND". The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception. e RS-232C The RS-232C port is to be used in conjunction with an external controller to control the operation of the SR5600 by using an external device. r COMPONENT VIDEO INPUT/OUTPUT If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the SR5600. The SR5600 has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. When the video convert function is enabled, video and S-video images can be output to the COMPONENT MOINTOR OUT jack. t MONITOR OUT This is a monitor output and each one includes both composite video and S-video configurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections. 6 y Preamp Outputs (L, R, SL, SR, SBL, SBR, C) Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power amplifiers. u AC INLET Plug the supplied power cord into this AC INLET and then into the power outlet on the wall. SR5600 can be powered by 120V AC only. i AC OUTLETS Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided. The one marked SWITCHED provides power only when the SR5600 is turned on and is useful for components which you use every time you play your system. The one marked UNSWITCHED is always live as long as the SR5600 is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with via its own power switch. Caution: • In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the SR5600 is turned on. • The capacity of this AC outlet is 120W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply. o Speaker outputs terminals Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers. Note: • You can use surround back speaker terminals as M (Multiroom) SPEAKER B terminals, when you use no surround back speaker. !0 Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. !1 7.1 CHANNEL or AUX2 INPUT By connecting a DVD Audio player, SACD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs. !2 Multiroom Outputs (Audio L&R) These are the audio output jacks for the Multi zone (Multi room). Connect these jacks to optional audio power amplifiers to listen the source selected by the multiroom system in a remote room. !3 MULTI ROOM REMOTE IN/OUT terminals IN: Connect to a multi-room remote control device, available from your Marantz dealer. OUT: Connect to the Marantz component equipped with remote control (RC-5) terminals in Multi zone (Multi room). !4 REMOTE CONT. IN/OUT terminals Connect to a Marantz component equipped with remote control (RC-5) terminals. !5 AUDIO IN/OUT (CD, TAPE, CD-R, TV, DVD, VCR1, DSS/VCR2) These are the analog audio inputs and outputs. There are 7 audio inputs (4 of which are linked to video inputs) and 4 audio outputs (2 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs and outputs require RCA-type connectors. !6 DIGITAL INPUT (Dig.1 - 4) / OUTPUT (coaxial, optical) These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 2 with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components.