Marantz SR7400 SR7400 User Guide - Page 17
Advanced Connecting, Connecting The Remote Control Jacks
View all Marantz SR7400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
ENGLISH ADVANCED CONNECTING CONNECTING THE REMOTE CONTROL JACKS RL RLRL DVD AUDIO PLAYER or SACD MULTI CHANNEANLTENPNALAYER COMPONENT VIDEO INPUT-1 INPUT-2 Y CB/PB CR/PR Y CB/PB CR/PR MONITOR OUT Y CB/PB CR/PR FM (75Ω) GND AM VIDEO TV DVD VCR1 IN OUT DSS/VCR2 MONITOR MULTI IN OUT OUT OUT TV DVD VCR1 IN OUT S-VIDEO DSS/VCR2 MONITOR IN OUT OUT RS-232C MULTI RC-5 RC FLASHER IN L SL DIGITAL IN DIGITAL OUT IN 1 2 3 4 5 6 OPT. COAX. CENTER L R FRONT TV DVD VCR1 DSS/VCR2 L SURR. SURR. SUB R BACK WOOFER IN OUT IN OUT CD TAPE IN OUT AUDIO OUT DC OUT R SR CDR/MD MULTI L SL IN OUT OUT R SR (AUX2) SBL SBR SBL SBR C PRE OUT SW C 7.1CH IN SW RL RL RL RL RL RL MODEL NO.SR7400 L CENTER R LR FRONT SURROUND BACK / MULTI SPEAKER POWER AMPLIFER SURR. AC IN SURR. SUB BACK WOOFER SWITCHED UNSWITCHED 1A 120W MAX 1A 120W MAX AC OUTLETS 120V 60HZ R L R L R L Subwoofer FRONT A FRONT B CENTER SPEAKER SYSTEMS FRONT A OR B, CENTER, SURROUND, SURR. BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS SURROUND LR LRLR Front Left Center Front Right Surround Left Surround Right ANTENNA COMPONENT VIDEO INPUT-1 Y CB/PB CR/PR INPUT-2 Y CB/PB CR/PR MONITOR OUT Y CB/PB CR/PR FM (75Ω) GND AM VIDEO TV DVD VCR1 IN OUT DSS/VCR2 MONITOR MULTI TV IN OUT OUT OUT DVD VCR1 IN OUT S-VIDEO DSS/VCR2 MONITOR IN OUT OUT RS-232C 1 TV L R DIGITAL IN 2 3 4 DVD VCR1 IN OUT MULTI RC-5 RC FLASHER IN L DIGITAL OUT IN 5 6 OPT. COAX. DSS/VCR2 CD TAPE OUT CDR/MD DC OUT R MULTI L SL SBL C PRE OUT SR SBR SW SL SBL C IN OUT 7.1CH IN IN OUT IN OUT OUT R SR SBR SW AUDIO (AUX2) MODEL NO.SR7400 R L 2 SURROUND BACK / MULTI SPEAKER R L R AC IN SWITCHED UNSWITCHED 1A 120W MAX 1A 120W MAX AC OUTLETS 120V 60HZ RC OUT L R L OPTION FRONT A FRONT B CENTER SPEAKER SYSTEMS FRONT A OR B, CENTER, SURROUND, SURR. BACK : MINIMUM 6 OHMS FRONT A AND B : MINIMUM 8 OHMS SURROUND 1 REMOTE CONTROL IN OUT CD RECORDER EXTERNAL INTERNAL REMOTE CONTROL IN OUT MD DECK EXTERNAL INTERNAL REMOTE CONTROL IN OUT CD PLAYER EXTERNAL INTERNAL CONNECTING MULTI CHANNEL AUDIO SOURCE The 7.1CH INPUT jacks are for multichannel audio source such as a SACD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 21. 14 Surround Back Left Surround Back Right CONNECTING AN EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifiers. Be sure to connect each speaker to the corresponding external power amplifier. q You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the SR7400, be sure to always disable operation of the infrared sensor on the main unit by using the following procedure. 1. Hold down the SELECT button and TV button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the SELECT button to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled. Note: Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE".