Marantz ZR6001SP ZR6001 User Manual - Page 34

ENGLISH OTHER FUNCTION TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/ OFF) to the ZR6001. AUTO POWER ON 1. Be sure the TV auto mode is ENABLED. (Refer page 22 : System Setup) 2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input. 3. Turn OFF the power to the TV TUNER and the ZR6001. 4. Turn ON the TV TUNER and tune in a receivable station. 5. When the station is received, the ZR6001 turns ON and TV is selected automatically. AUTO POWER OFF 1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast. 2. The power to the ZR6001 switches to STANDBY after approx. 5 minutes. Notes: • AUTO POWER OFF is canceled if the ZR6001 is set to a source other than TV. The function reactivates when TV is selected again. • Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. • The S-Video terminal does not support "TV AUTO ON/OFF" function. ATTENUATION TO ANALOG INPUT SIGNAL T-MODE RDS F.DIRECT INPUT/DISC+ AUDIO SUB-T/ATT PTY CH.SEL LIP.SYNC SYSTEM REMOTE CONTROLLER RC5500SR DOLBY HEADPHONE MODE This feature simulates the waveforms of the actual sounds heard from the speakers. When headphones are used, the MENU button automatically switches to the Dolby headphone mode. The OSD that appears when the MENU button is pressed is shown below. HEAD PHONE If the selected analog audio input signal is greater than the capable level of internal processing, the "PEAK" indicator will light up on the front display. If this happens, you should press the ATT button on the remote. "ATT" indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MDOUT, VCR1-OUT and DSS/VCR2-OUT. This function is memorized for each individual input source. DOLBY HP MODE SURROUND L LEVEL R LEVEL : BYPASS : ✽✽✽ : 0dB : 0dB DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons. #:1"44 1"44 LISTENING THROUGH HEADPHONES This jack may be used to listen to the ZR6001's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phono plug. (Note that the speakers will automatically be turned off when the headphone jack is in use.) DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - DISC 6.1 SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER Note: • The surround mode returns to the previous setting as soon as the plug is removed from the jack. BYPASS : Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo. DH1 : The size of a typical living room space is simulated. DH2 : The expansiveness of a structure as large as a music hall is simulated. DH3 : A large space such as that found in a movie theater is simulated. When the PURE DIRECT mode is selected, Dolby surround processing is bypassed and is displayed as the mode indication. The surround mode can be selected when any of the modes in DH1, DH2, or DH3 is selected. DISPLAY MEMORY CLEAR L/R LEVEL EXIT BAND T-MODE can be set in the ±10 dB range. Notes: • The surround mode returns to the previous setting as soon as the plug is removed from the jack. • TONE cannot be set when any of the modes in DH1, DH2, or DH3 is selected. • The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input. VIDEO ON/OFF When no video signal is connected to the ZR6001 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the "VIDEO OFF" setting. To select video off, press the AMP button and press the V-OFF button. TUNER CD TAPE CDR/MD DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MTX 6.1 SPKR B EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE AUX1 TV VOL. SLEEP AMP MUTE MAIN VOL. OSD MENU NIGHT DISPLAY CLEAR CSII 4 MCH-ST 7 MEMO EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH DISPLAY MODE DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MTX 6.1 SPKR B EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR SURROUND MODE PURE DIRECT SIMPLE SETUP AUTO HT-EQ MENU ENTER DISPLAY MEMORY CLEAR EXIT BAND T-MODE SET UP/ T.TONE PURE DIRECT AUTO 1 NIGHT CSII 4 DISPLAY MCH-ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES 5 VIRTUAL 6 STEREO 8 7.1CH IN 9 A/D P.SCAN/V-OFF 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH T-MODE RDS F.DIRECT You can select the display mode for the front display of the ZR6001. To select this mode, press the DISPLAY on the remote control. When this button is pressed, the display mode is switched in the following sequence. → Surround Mode → Auto-display Off → Display Off → Input Function → Surround Mode.... In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed. In Display off mode, the display is off completely. Note: • Only the DISP indicator will be illuminated on the front display in display off condition 31