Maytag MEDC500VW Installation Instructions - Page 14

Reversible Large, Reversible

Get Maytag MEDC500VW - Centennial Series 29 Inch Electric Dryer PDF manuals and user guides
UPC - 883049145747
View all Maytag MEDC500VW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

You can change your door swing from a right-side opening to a left-side opening, if desired, Reversible Large Side-Swing Door 3. Lift door until top screws in cabinet are in large part of hinge slot. Pull door forward off screws. Set door (handle side up) on top of dryer. Remove top screws from cabinet. 4. Remove screws attaching hinges to door. 5. Remove screws at top, bottom and side of door (4 screws). Holding door over towel on dryer, grasp sides of outer door and gently lift to separate it from inner door. Do not pry apart with putty knife. Do not pull on door seal or plastic door catches. 6. Be certain to keep cardboard spacer centered between doors. Reattach outer door panel to inner door panel so handle is on the side where hinges were just removed. 1. Place towel (A) on top of dryer to protect surface. 2. Open dryer door. Remove bottom screws from cabinet side of hinges (C). Loosen (do not remove) top screws from cabinet side of hinges. 3. Lift door until top screws in cabinet are in large part of hinge slot. Pull door forward off screws. Set door on top of dryer. Remove top screws from cabinet. 4. Use a small, flat-blade screwdriver to gently remove 4 hinge hole plugs (D) on left side of cabinet. Insert plugs into hinge holes on right-hand side of cabinet. 5. Insert screws into bottom holes on left side of cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges. 7. Attach door hinges to dryer door so that the larger hole is at the bottom of the hinge. 8. Remove door strike (E) from cabinet. Use a small, flat-blade screwdriver to gently remove 4 hinge hole plugs (F) on left side of cabinet. Insert plugs into hinge holes on right side of cabinet. 9. Insert screws into bottom holes on left side of cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges. 6. Close door and check that door strike aligns with door catch (B). If needed, slide door catch left or right within slot to adjust alignment. Reversible Super Wide Side-Swing Door 10. Remove door strike plug (B). Insert the door strike you removed in Step 8 into hole and secure with screw. Insert door strike plug into original door strike hole and secure with screw. 11. Close door and check that door strike aligns with door catch (C). If it is needed, slide door catch left or right within slot to adjust alignment. 1. Place towel (A) on top of dryer to protect surface. 2. Open dryer door. Remove bottom screws from cabinet side of hinges (D). Loosen (do not remove) top screws from cabinet side of hinges. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
You can change your door swing from a right-side
opening to a
3.
Lift door until top screws
in cabinet
are in large part of hinge
left-side
opening,
if desired,
slot. Pull door forward
off screws. Set door (handle side up) on
Reversible Large
Side-Swing
Door
top of dryer. Remove top screws from cabinet.
4.
Remove screws
attaching
hinges to door.
5.
Remove screws at top, bottom
and side of door (4 screws).
Holding
door over towel on dryer, grasp sides of outer door
and gently lift to separate
it from inner door. Do not pry apart
with putty knife. Do not pull on door seal or plastic
door
catches.
6.
Be certain to keep cardboard
spacer centered
between doors.
Reattach
outer door panel to inner door panel so handle is on
the side where hinges were just removed.
1.
Place towel (A) on top of dryer to protect surface.
2.
Open dryer door. Remove bottom
screws from cabinet side of
hinges (C). Loosen (do not remove) top screws from cabinet
side of hinges.
3.
Lift door until top screws
in cabinet
are in large part of hinge
slot. Pull door forward
off screws. Set door on top of dryer.
Remove top screws from cabinet.
4.
Use a small, flat-blade
screwdriver
to gently remove 4 hinge
hole plugs
(D) on left side of cabinet.
Insert plugs into hinge
holes on right-hand
side of cabinet.
5.
Insert screws into bottom
holes on left side of cabinet.
Tighten
screws
halfway. Position door so large end of door hinge slot
is over screws.
Slide door up so screws are in bottom
of slots.
Tighten screws.
Insert and tighten
top screws
in hinges.
6.
Close door and check
that door
strike aligns with door catch
(B). If needed, slide door catch
left or right within slot to adjust
alignment.
Reversible
Super Wide Side-Swing
Door
7.
Attach door hinges to dryer door so that the larger hole is at
the bottom
of the hinge.
8.
Remove door strike (E) from cabinet.
Use a small, flat-blade
screwdriver
to gently remove 4 hinge hole plugs (F) on left side
of cabinet.
Insert plugs into hinge holes on right side of
cabinet.
9.
Insert screws
into bottom
holes on left side of cabinet.
Tighten
screws
halfway. Position door
so large end of door hinge slot
is over screws.
Slide door up so screws are in bottom of slots.
Tighten screws.
Insert and tighten top screws
in hinges.
10.
Remove door strike plug (B). Insert the door strike you
removed
in Step 8 into hole and secure with screw. Insert door
strike plug into original door strike hole and secure with screw.
11. Close door and check
that door strike aligns with door catch
(C). If it is needed,
slide door catch left or right within
slot to
adjust alignment.
1.
2.
Place towel (A) on top of dryer to protect surface.
Open dryer door. Remove bottom
screws from cabinet side of
hinges (D). Loosen (do not remove) top screws
from cabinet
side of hinges.
14