Miele Complete C3 Cat & Dog Product Manual - Page 10

Before using the vacuum, cleaner

Get Miele Complete C3 Cat & Dog PDF manuals and user guides View all Miele Complete C3 Cat & Dog manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

en The illustrations referred to in the text are shown on the fold-out pages at the end of these operating instructions. Before using the vacuum cleaner Attaching the suction hose (see fig. 1) ^ Insert the elbow into the suction socket until it clicks into place. Adjusting the telescopic wand (see fig. 5) This telescopic wand is composed of two interlocking tube sections that can be adjusted to the desired length. ^ Press the adjustment button and slide the tubes to the desired length. Attaching the standard floor brush AllTeQ or AirTeQ (see fig. 6) (depending on model) Disconnecting the hose (see fig. 2) ^ Press the release buttons on the sides of the elbow and lift the hose from the socket. Connecting the suction hose and handpiece (see fig. 3) Depending on the model, the handpiece is already pre-fitted at the other end of the hose at the factory. If the handpiece of your model is separate, it just needs to be connected to the hose. ^ Insert the hose into the handpiece until it clicks into place. Connecting the telescopic wand and handpiece (see fig. 4) ^ Insert the handpiece into the telescopic wand until it clicks into place. Use the inlet guides of both parts to direct insertion. ^ To separate the parts from each other, press the wand release button and pull the handpiece away from the telescopic wand with a slight rotation. Observe the cleaning instructions of the floor manufacturer. ^ Place the floor brush on the telescopic wand and twist back and forth until it clicks into place. ^ To remove the floor brush from the telescopic wand, press the release button. The floor brush is intended for everyday use on carpets, rugs, and hard flooring that is not susceptible to scratching. For other floor coverings, we recommend using the special Miele brushes (see the section on "Optional accessories"). Adjusting the standard floor brush AllTeQ or AirTeQ (see fig. 7 + 8) (depending on model) Observe the cleaning instructions of the floor manufacturer. To clean carpets and rugs, lower the bristles by ^ pressing the foot switch %. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
The illustrations referred to in the text
are shown on the fold-out pages at the
end of these operating instructions.
Before using the vacuum
cleaner
Attaching the suction hose (see fig. 1)
^
Insert the elbow into the suction
socket until it clicks into place.
Disconnecting the hose (see fig. 2)
^
Press the release buttons on the
sides of the elbow and lift the hose
from the socket.
Connecting the suction hose and
handpiece (see fig. 3)
Depending on the model, the hand-
piece is already pre-fitted at the other
end of the hose at the factory. If the
handpiece of your model is separate, it
just needs to be connected to the hose.
^
Insert the hose into the handpiece
until it clicks into place.
Connecting the telescopic wand and
handpiece (see fig. 4)
^
Insert the handpiece into the
telescopic wand until it clicks into
place. Use the inlet guides of both
parts to direct insertion.
^
To separate the parts from each
other, press the wand release button
and pull the handpiece away from
the telescopic wand with a slight
rotation.
Adjusting the telescopic wand (see
fig. 5)
This telescopic wand is composed of
two interlocking tube sections that can
be adjusted to the desired length.
^
Press the adjustment button and
slide the tubes to the desired length.
Attaching the standard floor brush
AllTeQ or AirTeQ (see fig. 6)
(depending on model)
Observe the cleaning instructions of
the floor manufacturer.
^
Place the floor brush on the
telescopic wand and twist back and
forth until it clicks into place.
^
To remove the floor brush from the
telescopic wand, press the release
button.
The floor brush is intended for everyday
use on carpets, rugs, and hard flooring
that is not susceptible to scratching.
For other floor coverings, we recom-
mend using the special Miele brushes
(see the section on "Optional accesso-
ries").
Adjusting the standard floor brush
AllTeQ or AirTeQ (see fig. 7 + 8)
(depending on model)
Observe the cleaning instructions of
the floor manufacturer.
To clean carpets and rugs, lower the
bristles by
^
pressing the foot switch
%
.
en
10