Miele Crystal G 5225 Operating and Installation manual
Miele Crystal G 5225 Manual
View all Miele Crystal G 5225 manuals
Add to My Manuals
Save this manual to your list of manuals |
Miele Crystal G 5225 manual content summary:
- Miele Crystal G 5225 | Operating and Installation manual - Page 1
Operating Instructions Dishwasher G 5220 G 5225 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr. 09 510 211 - Miele Crystal G 5225 | Operating and Installation manual - Page 2
Contents IMPORTANT SAFETY INSTRUCTIONS 4 Guide to the dishwasher 7 Control panel 8 Caring for the environment 9 aid 17 Rinse aid indicator 18 Adjusting the dosage 19 Loading the dishwasher 20 Items not recommended for dishwashing 21 Typical load for 10 place settings with cutlery tray 22 - Miele Crystal G 5225 | Operating and Installation manual - Page 3
questions 45 Technical faults 45 Faults in the water intake or water drain 46 General problems with the dishwasher 47 Sounds 48 Poor cleaning results 49 After sales service 52 User Maintenance Instructions 53 Cleaning and Care 54 Triple filter system 55 Cleaning the drain pump and non - Miele Crystal G 5225 | Operating and Installation manual - Page 4
supported by the manufacturer and could be dangerous. ~ Persons who lack physical, sensory or mental abilities, or experience with the appliance should not use the dishwasher without supervision or instruction be replaced by a Miele Service technician with a genuine Miele power cord. ~ The outlet - Miele Crystal G 5225 | Operating and Installation manual - Page 5
IMPORTANT SAFETY INSTRUCTIONS Installation ~ The dishwasher must be installed and connected in accordance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the - Miele Crystal G 5225 | Operating and Installation manual - Page 6
IMPORTANT SAFETY INSTRUCTIONS Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. It is possible for small fingers may be pinched in the door. ~ Only use the dishwasher if all panels are properly in place. ~ Do not tamper with the controls. ~ Do not sit - Miele Crystal G 5225 | Operating and Installation manual - Page 7
Guide to the dishwasher a Upper spray arm (not visible) b Cutlery tray c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Triple filter system h - Miele Crystal G 5225 | Operating and Installation manual - Page 8
Guide to the dishwasher Control panel a Program selection b Time display c Program sequence (On/Off) This operating instruction manual describes several dishwasher models with different indicated settings. The different dishwasher models are named : Standard = Dishwasher with 31 11/16" ( - Miele Crystal G 5225 | Operating and Installation manual - Page 9
fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. ^ Make full use of the the amount of soiling and type of dishware being washed. See the "Program Guide" for more information. ^ When using powder or liquid detergent, reduce the amount - Miele Crystal G 5225 | Operating and Installation manual - Page 10
and pull the door open. If the door is opened during operation the dishwasher will stop running. Once the door is closed the program will restart. into place. Te child Safety Lock is designed to prevent children from opening the dishwasher. ^ To lock the door, push the slider below the door grip to - Miele Crystal G 5225 | Operating and Installation manual - Page 11
water hardness ß 22 gr/gal (21 °d) (see "Detergents"). - The dishwasher must be correctly programmed to match the hardness of your water. In areas where °d [52 gr/gal]). If there is a fault, it will help the service technician to know the hardness of your local water supply. Please note your water - Miele Crystal G 5225 | Operating and Installation manual - Page 12
value will raise one level. Once the highest value is reached the setting will start again from the beginning. ^ Press the K button to turn the dishwasher off. °d 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 - Miele Crystal G 5225 | Operating and Installation manual - Page 13
Before using for the first time Checking the programmed water hardness ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start/Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start/Stop" button pressed for at least four seconds until the " - Miele Crystal G 5225 | Operating and Installation manual - Page 14
the salt can dissolve properly. Water does not have to be added with subsequent refills. ,Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. If using "Tab" products which include salt, still add salt to - Miele Crystal G 5225 | Operating and Installation manual - Page 15
time. It will go out once the reactivation process is complete. The "Salt" indicator light is turned off if you have programmed the dishwasher to a water hardness below 4 °d (4 gr/gal). ,Immediately after each refill, run the "Express" program without a load (no "Turbo" function if available). This - Miele Crystal G 5225 | Operating and Installation manual - Page 16
turned off. ^ Press the "Start/Stop" button if you wish to change the setting. The setting is saved immediately. ^ Press the K button to turn the dishwasher off. If you switch to using detergent that does not contain salt or rinse aid, it is important to remember to replenish the salt and - Miele Crystal G 5225 | Operating and Installation manual - Page 17
will be automatically dosed. ,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" detergents rinse aid is not needed. Adding rinse aid ^ Pour liquid rinse aid into the reservoir - Miele Crystal G 5225 | Operating and Installation manual - Page 18
aid indicator on the control panel will light when the rinse aid reservoir needs refilling. If you only ever use "Tab" detergent products in your dishwasher, you can switch the reminders for salt and rinse aid off if you wish (see "Before using for the first time - Refill salt message"). If - Miele Crystal G 5225 | Operating and Installation manual - Page 19
touch of the button increases the level. The programmed dosage is saved. ^ Turn the dishwasher off "s". ^ Turn the dishwasher off "s". ^ Press the "Start / Stop" button and at the same time turn the dishwasher on s. Hold the "Start / Stop" button until the "Start / Stop" indicator comes on. If - Miele Crystal G 5225 | Operating and Installation manual - Page 20
through the baskets. Check clearance by manually rotating the spray arms. ^ Place very small items in the cutlery tray or basket so they do not fall to the bottom of the wash cabinet. ^ Food residue and spilled liquids should be cleaned from the sides of the dishwasher door. These are outside of - Miele Crystal G 5225 | Operating and Installation manual - Page 21
hand. - When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe. Only wash items marked "dishwasher safe" in the dishwasher. - If fine glassware is washed in the dishwasher select the "China & Crystal" program*. This will reduce the risk of clouding. Silver and aluminum - Miele Crystal G 5225 | Operating and Installation manual - Page 22
Loading the dishwasher Typical load for 10 place settings with cutlery tray Upper basket Lower basket Cutlery tray 22 - Miele Crystal G 5225 | Operating and Installation manual - Page 23
Loading the dishwasher Typical load for 16 place settings with cutlery tray Upper basket Lower basket Cutlery tray 23 - Miele Crystal G 5225 | Operating and Installation manual - Page 24
Loading the dishwasher Typical load for 10 place settings with cutlery basket Upper basket Lower basket Cutlery basket 24 - Miele Crystal G 5225 | Operating and Installation manual - Page 25
Loading the dishwasher Typical load for 13 place settings with cutlery basket Upper basket Lower basket Cutlery basket 25 - Miele Crystal G 5225 | Operating and Installation manual - Page 26
Upper basket ,Always use the dishwasher with the upper and lower basket in place. Adjustable cup rack (depending on model) ^ Raise the rack to make room for tall glasses. Glasses can - Miele Crystal G 5225 | Operating and Installation manual - Page 27
Loading the dishwasher Adjusting the upper basket To adjust the upper basket downwards: In order to gain more space for taller items the upper basket can be adjusted - Miele Crystal G 5225 | Operating and Installation manual - Page 28
lower basket. It can also be used for glasses, cups, small plates and saucers. Heavily soiled items Dishwasher with cutlery tray ^ Place very large plates in the center of the lower basket. Dishwasher with cutlery basket When tilted, plates up to 13 3/4" (35 cm) in diameter can be accommodated - Miele Crystal G 5225 | Operating and Installation manual - Page 29
Loading the dishwasher MultiComfort zone The rear section of the lower basket is used for cups, glasses, plates, pots and pans. ^ The glass rack can be folded up - Miele Crystal G 5225 | Operating and Installation manual - Page 30
Loading the dishwasher Cutlery tray (depending on model) ^ Arrange the cutlery as shown in the cutlery tray. Spoons with thick handles may have to be placed as knives - Miele Crystal G 5225 | Operating and Installation manual - Page 31
Cutlery basket (depending on model) Loading the dishwasher Cutlery insert for the cutlery basket Use the insert supplied for heavily soiled items of cutlery. The insert separates the items so that they can - Miele Crystal G 5225 | Operating and Installation manual - Page 32
additional items of cutlery ... a cutlery basket for the lower basket. ...wash long-stemmed glassware ... a glassware rack for the lower basket. MieleCare Collection Miele branded cleaning and care products, including dishwasher salt, detergent and rinse aid, are available to order from your - Miele Crystal G 5225 | Operating and Installation manual - Page 33
cleaning products are available from MIele. ,Only use detergents formulated for domestic dishwashers. Use only the recommended amount of detergent. Continued use of too much detergent may cause machine damage. When using the "China & Crystal" program (depending on model) reduce the amount - Miele Crystal G 5225 | Operating and Installation manual - Page 34
Use Adding detergent ^ Press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to the compartments and close the container flap. ^ Use one tab or add powder or gel detergent to compartment II and close the flap. ^ If a - Miele Crystal G 5225 | Operating and Installation manual - Page 35
water supply if it is closed. ^ Press the K button to turn the dishwasher on. The Start/Stop indicator flashes, and the indicator for the last selected program program according to the type of dishware and soiling. See Program guide for a description of the programs and their applications. ^ Use - Miele Crystal G 5225 | Operating and Installation manual - Page 36
Use Program guide When to use Program sequence Pre-rinse Main wash Interim rinse Final energy and water consumption based on the soil load of the dishware. X X China & Crystal For temperature sensitive glassware and lightly soiled dishware, use 50% detergent recommended. as requi red - Miele Crystal G 5225 | Operating and Installation manual - Page 37
off and only the Start/Stop indicator light flashes slowly. ^ Press the K button if you want to turn the indicator lights back on. If the dishwasher is not turned off or opened after the program ends, after a few minutes in standby mode it will turn off completely (see Additional options Optimize - Miele Crystal G 5225 | Operating and Installation manual - Page 38
was selected, the drying fan will run for a few minutes after the program has ended. ^ Open the door. ^ Press the K button to turn the dishwasher off. The dishwasher will continue to use electricity until it is turned off with the K button. The dishes will cool much faster if you open the door - Miele Crystal G 5225 | Operating and Installation manual - Page 39
as soon as the door is opened. When the door is closed again, the program will continue from where it was interrupted. ,Water in the dishwasher is hot. Risk of scalding! Only open the door if absolutely necessary and be very careful. Before closing the door again, leave it slightly ajar - Miele Crystal G 5225 | Operating and Installation manual - Page 40
-times, in programs in which the option is available. Energy consumption will increase to achieve optimum results. ^ Press the K button to turn the dishwasher on. The Start/Stop indicator light flashes. ^ Select the desired program. ^ Press the Turbo button. The Turbo indicator light comes on. ^ Now - Miele Crystal G 5225 | Operating and Installation manual - Page 41
and not be rinsed out completely. Do not use liquid detergent. Liquid detergent could leak out of the compartment. ^ Press the K button to turn the dishwasher on. The Start/Stop indicator light flashes. ^ Use the Program button to select the desired program. ^ Press the Delay start button. The last - Miele Crystal G 5225 | Operating and Installation manual - Page 42
Additional options The time will count down to the program start: for more than 10 hours in 1 hour increments, for less than 10 hours in 1 minute increments. When the set time is reached, the selected program will start automatically. The remaining time is shown in the time display, the Delay start - Miele Crystal G 5225 | Operating and Installation manual - Page 43
it will turn off completely. You can also deactivate the Optimize Standby function. The display and the indicator lights do not go out, and the dishwasher turns off 6 hours after the end of the program. This results in higher energy consumption. If Salt and/or Rinse aid or a fault is displayed - Miele Crystal G 5225 | Operating and Installation manual - Page 44
have changed any settings, you can reset them to the factory defaults. ^ Press the K button to turn the dishwasher off. ^ Press and hold the Start/Stop button and simultaneously turn the dishwasher on using the K button. Keep the Start/Stop button pressed for at least four seconds until the "Start - Miele Crystal G 5225 | Operating and Installation manual - Page 45
Problem Possible fault Solution After turning on the dishwasher with the K button, the Start/Stop indicator light does not flash. The dishwasher correct fuse rating). - If the circuit breaker trips again, contact Miele. The program sequence indicators Main wash, Drying and End all flash - Miele Crystal G 5225 | Operating and Installation manual - Page 46
or water drain Problem The Intake/Drain indicator light alternates between flashing and remaining steady. The dishwasher stops running. The the way. - Clean the screen in the water supply valve (see User maintenance instructions). - The water pressure at the water connection is less than 4.35 psi. - Miele Crystal G 5225 | Operating and Installation manual - Page 47
questions General problems with the dishwasher Problem Possible fault Solution The time display is dark. Only the Start/Stop indicator light flashes slowly. The dishwasher has gone non-return valve (see User maintenance instructions). There is a kink in the drain Remove the kink. hose. 47 - Miele Crystal G 5225 | Operating and Installation manual - Page 48
Frequently asked questions Sounds Problem There is a knocking noise in the wash cabinet There is a rattling noise in the wash cabinet There is a knocking This may be caused by the installation or the diameter of the pipe. This has no effect on the dishwasher. If in doubt, contact a plumber. 48 - Miele Crystal G 5225 | Operating and Installation manual - Page 49
asked questions Poor cleaning results Problem Possible fault Solution The dishes are not The dishes were not loaded See "Loading the clean. correctly. dishwasher". The program was not powerful enough. Select a more intensive program (see "Program Guide"). Not enough detergent was Use - Miele Crystal G 5225 | Operating and Installation manual - Page 50
Frequently asked questions Problem Possible fault Solution Dishes are not dry, The rinse aid setting may be Increase the dosage, refill glasses and too low, or the rinse aid - Miele Crystal G 5225 | Operating and Installation manual - Page 51
Frequently asked questions Problem Possible fault Solution Glasses have a Detergent deposits. brown or blue discoloration; film cannot be wiped off. Change detergent right away. Glasses are dull and Glasses are not dishwasher There is no remedy. discolored; film safe. The surface is - Miele Crystal G 5225 | Operating and Installation manual - Page 52
the Miele Service Department at the phone number on the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to update the dishwasher to - Miele Crystal G 5225 | Operating and Installation manual - Page 53
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use. - Miele Crystal G 5225 | Operating and Installation manual - Page 54
dishwasher regularly. This will help avoid problems and faults. ,Abrasive cleaning agents, all-purpose cleaners, thinner or ammonia based cleaners should not be used on the dishwasher can be cleaned with a dishwasher cleaner such as "Dis Cleaner" available from your Miele dealer or online at www. - Miele Crystal G 5225 | Operating and Installation manual - Page 55
. The level of soiling and time it takes before the filters need cleaning will vary depending on your household usage. ^ Turn off the dishwasher before cleaning. ^ Turn the handle counterclockwise to release the triple filter system a. ^ Lift the filter combination out of the machine b. Remove any - Miele Crystal G 5225 | Operating and Installation manual - Page 56
Cleaning and Care To clean the inside of the filter, the flap must be opened. ^ Push the clips together a and open the flap b. ^ Rinse under running water. ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Lock the filter by turning - Miele Crystal G 5225 | Operating and Installation manual - Page 57
Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and - Miele Crystal G 5225 | Operating and Installation manual - Page 58
not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a cup or bowl to scoop water out of the wash cabinet. The - Miele Crystal G 5225 | Operating and Installation manual - Page 59
Installation Instructions Please refer to the Installation Diagram supplied with these instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. - Miele Crystal G 5225 | Operating and Installation manual - Page 60
use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED. ,Improper - Miele Crystal G 5225 | Operating and Installation manual - Page 61
. ,CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit the terminal block and the strain relief are tightened. GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED. This appliance must be connected - Miele Crystal G 5225 | Operating and Installation manual - Page 62
shown. See "Frequently Asked Questions" for more information. - If the water pressure is higher than shown, a pressure reducing valve must be used. - The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot (max - Miele Crystal G 5225 | Operating and Installation manual - Page 63
internal diameter of 7/8" (22 mm). - Drain hose extensions and adapters can be ordered from Miele. The maximum drain hose length is 13 ft. (4 m), max. drain height: 39" (1 m). Venting the drainage system If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than - Miele Crystal G 5225 | Operating and Installation manual - Page 64
General requirements for measuring noise The dishwasher must be loaded with 16 place settings and the Normal program must be used. Installation requirements for measuring noise The dishwasher must be installed as follows:. ^ Install the dishwasher into an appropriate housing unit. ^ Secure - Miele Crystal G 5225 | Operating and Installation manual - Page 65
Noise measurement ^ Push the insulation mat supplied (depending on model) under the plinth until it is up against the appliance feet a. ^ Attach the toe-kick so that it is flush with the door front b. 65 - Miele Crystal G 5225 | Operating and Installation manual - Page 66
66 - Miele Crystal G 5225 | Operating and Installation manual - Page 67
67 - Miele Crystal G 5225 | Operating and Installation manual - Page 68
Alteration rights reserved / 0313 G5220/G5225 / M.-Nr. 09 510 211 / 01 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
Operating Instructions
Dishwasher
G 5220
G 5225
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
M.-Nr. 09 510 211
en - US, CA