Miele Crystal G 5225 Operating and Installation manual - Page 37

Time display 37, Standby 37

Get Miele Crystal G 5225 PDF manuals and user guides View all Miele Crystal G 5225 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Use Time display Before the program starts, the time display shows the time of the selected program in hours and minutes. The remaining time is displayed during the program. The time that is displayed may vary for the same program. It depends on the temperature of the incoming water, the reactivation cycle, the type of detergent and the quantity and soiling of the dishes. When a program is selected for the first time, the display shows an average program runtime for cold water. With every program, the electronics correct the runtime according to the temperature of the incoming water and the size of the load. Standby A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The time display and the indicator lights are turned off and only the Start/Stop indicator light flashes slowly. ^ Press the K button if you want to turn the indicator lights back on. If the dishwasher is not turned off or opened after the program ends, after a few minutes in standby mode it will turn off completely (see Additional options Optimize Standby). If Salt and/or Rinse aid or a fault is displayed, the dishwasher will not switch to Standby mode. If you use a Tab detergent, you can deactivate the refill indicators to let the dishwasher go into Standby mode. However, fault messages cannot be turned off. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Time display
Before the program starts, the time
display shows the time of the selected
program in hours and minutes. The
remaining time is displayed during the
program.
The time that is displayed may vary for
the same program. It depends on the
temperature of the incoming water, the
reactivation cycle, the type of detergent
and the quantity and soiling of the
dishes.
When a program is selected for the first
time, the display shows an average
program runtime for cold water.
With every program, the electronics
correct the runtime according to the
temperature of the incoming water and
the size of the load.
Standby
A few minutes after the last button is
pressed or a few minutes after the end
of the program the dishwasher will
switch to Standby mode to save
energy. The time display and the
indicator lights are turned off and only
the Start/Stop indicator light flashes
slowly.
^
Press the
K
button if you want to turn
the indicator lights back on.
If the dishwasher is not turned off or
opened after the program ends, after a
few minutes in standby mode it will turn
off completely (see Additional options -
Optimize Standby).
If Salt and/or Rinse aid or a fault is
displayed, the dishwasher will not
switch to Standby mode.
If you use a Tab detergent, you can
deactivate the refill indicators to let
the dishwasher go into Standby
mode.
However, fault messages cannot be
turned off.
Use
37