Motorola 49901 Instruction Manual - Page 86

Adding/Removing, SDRAM DIMM, FLASH SIMM, Data Compression, Encryption SIMM

Get Motorola 49901 - Vanguard 340 Router PDF manuals and user guides
UPC - 786523499018
View all Motorola 49901 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Modifying Your Vanguard 340 and 340 Enhanced Note The location of the FLASH SIMM and Data Compression (DCC/DSP)/ Encryption SIMM are indicated on the motherboard as shown in Figure 3-8. Adding/Removing SDRAM DIMM Use these steps to add and remove a SDRAM DIMM: 1) Insert the DIMM into slot U173 as shown in Figure 3-7. 2) Carefully press the DIMM into the socket. 3) Lock the DIMM into place with the locking levers. 4) To remove the DIMM, disengage the locking levers by pushing them forward, and then lift out the DIMM. Adding/Removing FLASH SIMM Use these steps to add and remove a FLASH SIMM: 1) At a slight angle, insert the SIMM into connector U181 as shown in Figure 3-7. 2) Carefully press the SIMM down, pushing the locking tabs through the holes. The clips click into place. 3) To remove the SIMM, use your fingers to push back the two metal retaining clips and lift out the SIMM. Adding/Removing To add and remove a Data Compression/Encryption SIMM on a Vanguard 340: Data Compression/ Encryption SIMM 1) At a slight angle, insert the SIMM into the J39 connector, lining up the holes with the tab as shown in Figure 3-7. 2) Carefully press the SIMM down, pushing the locking tabs through the holes. The clips click into place. 3) Lock the SIMM into place with the locking levers. 4) To remove the SIMM, use your fingers to push back the two metal retaining clips and lift out the SIMM. 3-28 Installation and Replacement

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
3-28
Installation and Replacement
Modifying Your Vanguard 340 and 340 Enhanced
Note
The location of the FLASH SIMM and Data Compression (DCC/DSP)/
Encryption SIMM are indicated on the motherboard as shown in Figure 3-8.
Adding/Removing
SDRAM DIMM
Use these steps to add and remove a SDRAM DIMM:
1)
Insert the DIMM into slot U173 as shown in Figure 3-7.
2)
Carefully press the DIMM into the socket.
3)
Lock the DIMM into place with the locking levers.
4)
To remove the DIMM, disengage the locking levers by pushing them forward,
and then lift out the DIMM.
Adding/Removing
FLASH SIMM
Use these steps to add and remove a FLASH SIMM:
1)
At a slight angle, insert the SIMM into connector U181 as shown in Figure 3-7.
2)
Carefully press the SIMM down, pushing the locking tabs through the holes. The
clips click into place.
3)
To remove the SIMM, use your fingers to push back the two metal retaining clips
and lift out the SIMM.
Adding/Removing
Data Compression/
Encryption SIMM
To add and remove a Data Compression/Encryption SIMM on a Vanguard 340:
1)
At a slight angle, insert the SIMM into the J39 connector, lining up the holes
with the tab as shown in Figure 3-7.
2)
Carefully press the SIMM down, pushing the locking tabs through the holes. The
clips click into place.
3)
Lock the SIMM into place with the locking levers.
4)
To remove the SIMM, use your fingers to push back the two metal retaining clips
and lift out the SIMM.