NordicTrack Exp2000 Treadmill English Manual - Page 7

ing Handrail Bolts with Handrail Star Washers into

Get NordicTrack Exp2000 Treadmill PDF manuals and user guides View all NordicTrack Exp2000 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

4. Set the Console (99) and the Handrail (27) on the floor. Locate the Handrail Wire Harness (30) in the Handrail (27). Open the included small white box by lifting on the tab. Close the box over the Handrail Wire Harness as shown. Make sure that the tab is fully closed. Note: If two boxes are included, attach both boxes. While a second person holds the Console (99), connect the 8-pin wire of the Handrail Wire Harness (30) to the HD2 connector on the back of the Console. Next, connect the 4-pin wire to the IFIT2 connector, and the 3-pin wire to the HD1 connector in the location shown. 4 HD2 99 27 HD1 IFIT2 30 White Box 5. Attach the Console (99) to the Handrail (27) with the four Small Screws (6). Make sure that the Handrail Wire 5 6 Harness (not shown) is not pinched between the 99 Console and the Handrail. 6 27 6 6. Place a Handrail Cover (53) on each Upright (23). Make sure that the Handrail Covers are turned as shown in the inset drawing. Have a second person hold the Handrail (27) in the position shown. Connect the Handrail Wire Harness (30) to the Upright Wire Harness (100). Insert both Wire Harnesses into the right Upright (23). Hold a Metal Spacer (114) inside the right Upright (23) and align it with the first hole in the Upright. Insert a Handrail Bolt (25) with a Handrail Star Washer (26) through the Upright and the Metal Spacer. Hold the Handrail (27) above the Handrail Covers (53) and finger tighten the Handrail Bolt into the Handrail. Repeat this procedure on the left side. Then, tighten the two remaining Handrail Bolts with Handrail Star Washers into the Handrail. Be careful not to pinch the wires. Tighten all of the bolts used in steps 3 and 6. Press the Large Endcaps (86) into the Uprights (23). 6 23 27 53 23 86 27 114 53 26 25 30 114 86 53 100 26 23 25 7. Make sure that all parts are tightened before you use the TREKKER. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 22). To protect the floor or carpet from damage, cover the floor under the TREKKER. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
7
7.
Make sure that all parts are tightened before you use the TREKKER.
Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 22). To protect the floor or carpet
from damage, cover the floor under the TREKKER.
6.
Place a Handrail Cover (53) on each Upright (23). Make
sure that the Handrail Covers are turned as shown in the
inset drawing.
Have a second person hold the Handrail (27) in the posi-
tion shown. Connect the Handrail Wire Harness (30) to
the Upright Wire Harness (100). Insert both Wire
Harnesses into the right Upright (23).
Hold a Metal Spacer (114) inside the right Upright (23)
and align it with the first hole in the Upright. Insert a
Handrail Bolt (25) with a Handrail Star Washer (26)
through the Upright and the Metal Spacer. Hold the
Handrail (27) above the Handrail Covers (53) and finger
tighten the Handrail Bolt into the Handrail. Repeat this
procedure on the left side. Then, tighten the two remain-
ing Handrail Bolts with Handrail Star Washers into the
Handrail.
Be careful not to pinch the wires.
Tighten all of the bolts used in steps 3 and 6. Press the
Large Endcaps (86) into the Uprights (23).
6
26
53
25
27
25
53
86
114
86
114
26
23
23
30
100
27
53
23
4.
Set the Console (99) and the Handrail (27) on the floor.
Locate the Handrail Wire Harness (30) in the Handrail
(27). Open the included small white box by lifting on the
tab. Close the box over the Handrail Wire Harness as
shown. Make sure that the tab is fully closed.
Note: If
two boxes are included, attach both boxes.
While a second person holds the Console (99), connect
the 8-pin wire of the Handrail Wire Harness (30) to the
HD2 connector on the back of the Console. Next, con-
nect the 4-pin wire to the IFIT2 connector, and the 3-pin
wire to the HD1 connector
in the location shown
.
99
27
30
White
Box
HD1
HD2
IFIT2
4
5.
Attach the Console (99) to the Handrail (27) with the four
Small Screws (6).
Make sure that the Handrail Wire
Harness (not shown) is not pinched between the
Console and the Handrail.
6
99
6
6
27
5