NordicTrack Grt 500 English Manual - Page 10

Wrap the High Cable 73 over a 4² Pulley 35. Feed

Page 10 highlights

12. Disassemble the pre-assembled Pulley Plates (31). 12 Wrap the High Cable (73) around a 4Ó Pulley (35) in the direction shown. Attach the Pulley to the upper holes in the indicated ends of the Pulley Plates (31) with a 3/8Ó x 1 3/4Ó Bolt (60), a Cable Trap (44), and a 3/8Ó Nylon Jamnut (63). Make sure the Cable is in the groove of the Pulley and that the Cable Trap 31 is oriented so it holds the Cable in place. Set the remaining 4Ó Pulley (35), 3/8Ó x 1 3/4Ó Bolt (60), Cable Trap (44), and 3/8Ó Nylon Jamnut (63) aside. These parts will be used in step 19. 60 31 63 35 44 73 These adjustment holes must be at the bottom 13. IMPORTANT: If you purchased the optional leg press accessory (NTSA03990), please disregard steps 14 and 15 in this manual. To assemble the accessory, refer the userÕs manual accompanying it. After you have assembled the accessory, refer back to this manual and continue with step 16 on page 11. Feed the bolt on the High Cable (73) up through the indicated slot in the Top Frame (1). 13 1 Wrap the High Cable (73) over a 4Ó Pulley (35). Feed the bolt on the High Cable back down through the slot in the Top Frame (1). Attach the 4Ó Pulley (35) inside the slot in the Top Frame (1) with a 3/8Ó x 2 1/2Ó Bolt (54), two 3/8Ó Flat Washers (55), two 5/8Ó x 1/2Ó Pulley Bushings (42), and a 3/8Ó Nylon Jamnut (63). 35 63 55 42 Bolt 73 Slot 42 55 54 14. Detach the pre-assembled 4Ó Pulley (35) and Cable 14 Trap (44) from the Pulley Bracket (91). Save the 3/8Ó 92 x 1 3/4Ó Bolt (60) and the 3/8Ó Nylon Locknut (63). 71 Attach the Pulley Bracket (91) to the indicated hole in the Top Frame (1) with a 1/4Ó x 3 3/4Ó Bolt (92), two 1/4Ó Flat Washers (71), and a 1/4Ó Nylon Locknut (25) as shown. Make sure that the tab on top of the Pulley Bracket fits into the hole in the Top Frame as shown in the inset drawing. 91 63 Top Hole 71 Attach the 4Ó Pulley (35) and the Cable Trap (44) to the top hole in the Pulley Bracket (91) with the 3/8Ó x 1 3/4Ó Bolt (60) and the 3/8Ó Nylon Locknut (63). 25 Tab 44 35 60 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25

10
12.
Disassemble the pre-assembled Pulley Plates (31).
Wrap the High Cable (73) around a 4² Pulley (35) in
the direction shown. Attach the Pulley to the upper
holes in the indicated ends of the Pulley Plates (31)
with a 3/8² x 1 3/4² Bolt (60), a Cable Trap (44), and a
3/8² Nylon Jamnut (63).
Make sure the Cable is in
the groove of the Pulley and that the Cable Trap
is oriented so it holds the Cable in place.
Set the remaining 4² Pulley (35), 3/8² x 1 3/4² Bolt
(60), Cable Trap (44), and 3/8² Nylon Jamnut (63)
aside. These parts will be used in step 19.
12
73
60
31
44
35
31
63
These adjustment
holes must be at
the bottom
14
35
63
91
92
71
25
71
Top Hole
44
60
13.
IMPORTANT
:
If you purchased the optional leg
press accessory (NTSA03990), please disregard
steps 14 and 15 in this manual. To assemble the
accessory, refer the user°s manual accompanying
it. After you have assembled the accessory, refer
back to this manual and continue with step 16 on
page 11.
Feed the bolt on the High Cable (73) up through the
indicated slot in the Top Frame (1).
Wrap the High Cable (73) over a 4² Pulley (35). Feed
the bolt on the High Cable back down through the slot
in the Top Frame (1).
Attach the 4² Pulley (35) inside the slot in the Top
Frame (1) with a 3/8² x 2 1/2² Bolt (54), two 3/8² Flat
Washers (55), two 5/8² x 1/2² Pulley Bushings (42),
and a 3/8² Nylon Jamnut (63).
13
1
35
42
55
54
63
42
73
55
Bolt
Slot
14.
Detach the pre-assembled 4² Pulley (35) and Cable
Trap (44) from the Pulley Bracket (91). Save the 3/8²
x 1 3/4² Bolt (60) and the 3/8² Nylon Locknut (63).
Attach the Pulley Bracket (91) to the indicated hole in
the Top Frame (1) with a 1/4² x 3 3/4² Bolt (92), two
1/4² Flat Washers (71), and a 1/4² Nylon Locknut (25)
as shown. Make sure that the tab on top of the Pulley
Bracket fits into the hole in the Top Frame as shown
in the inset drawing.
Attach the 4² Pulley (35) and the Cable Trap (44) to
the top hole in the Pulley Bracket (91) with the 3/8² x
1 3/4² Bolt (60) and the 3/8² Nylon Locknut (63).
Tab