NordicTrack Gx 3.1 Bike Uk Manual - Page 8

Tip: Avoid pinching the Extension Wire 59., Avoid pinching the, Extension Wire 59

Get NordicTrack Gx 3.1 Bike PDF manuals and user guides View all NordicTrack Gx 3.1 Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Orient the Seat (23) and the Seat Carriage (24) as shown. Attach the Seat (23) to the Seat Carriage (24) with four M8 x 16mm Screws (74) and four M8 Split Washers (75). Slide the Seat Carriage (24) onto the Seat Post (6). Then, slide the Seat Carriage all the way forward and tighten the Seat Adjustment Knob (26). Attach an M4 x 5mm Bright Screw (91) to the rear of the Seat Post (6). 5 23 24 75 74 91 6 26 6. Using a plastic bag to keep your fingers clean, apply some of the included grease to the barrel of an M6 x 70mm Bolt Set (50). Orient the Handlebar (5) and the Upright (4) as shown. While a second person holds the Handlebar (5) near the Upright (4), insert the Extension Wire (59) upward through the Handlebar. Tip: Avoid pinching the Extension Wire (59). Attach the Handlebar (5) to the Upright (4) with the M6 x 70mm Bolt Set (50) and two M8 Washers (43). Then, attach the M6 x 60mm Bolt Set (51) through the lower bracket on the Handlebar (5). 6 59 50 51 43 5 Grease 43 50 51 4 Avoid pinching the Extension Wire (59) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
8
5
23
24
75
74
26
91
6
5.
Orient the Seat (23) and the Seat Carriage (24)
as shown.
Attach the Seat (23) to the Seat Carriage (24)
with four M8 x 16mm Screws (74) and four M8
Split Washers (75).
Slide the Seat Carriage (24) onto the Seat
Post (6). Then, slide the Seat Carriage all the
way forward and tighten the Seat Adjustment
Knob (26).
Attach an M4 x 5mm Bright Screw (91) to the
rear of the Seat Post (6).
6.
Using a plastic bag to keep your fingers clean,
apply some of the included grease to the barrel
of an M6 x 70mm Bolt Set (50).
Orient the Handlebar (5) and the Upright (4) as
shown.
While a second person holds the Handlebar (5)
near the Upright (4), insert the Extension Wire
(59) upward through the Handlebar.
Tip: Avoid pinching the Extension Wire (59).
Attach the Handlebar (5) to the Upright (4)
with the M6 x 70mm Bolt Set (50) and two M8
Washers (43).
Then, attach the M6 x 60mm Bolt Set (51)
through the lower bracket on the Handlebar (5).
6
59
5
43
43
50
51
51
50
4
Grease
Avoid pinching the
Extension Wire (59)