NordicTrack Vx9000 English Manual - Page 6

Assembly - repeater

Get NordicTrack Vx9000 PDF manuals and user guides View all NordicTrack Vx9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly can be completed using the included allen wrenches. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. 1. Slide the Right and Left Uprights (95, 97) onto the brackets near the front of the Frame (76). Make sure that the 1 Uprights are on the correct sides; the indicated holes must be facing inward. Raise the Right Upright (95) until the lower hole in the 97 front of the Upright is aligned with the upper hole in the bracket on the Frame (76). Thread an Upright Bolt (96) into the Upright and the bracket. Do not tighten the Upright Bolt yet. Holes 96 95 96 Repeat this step with the Left Upright (97). 76 2. While a second person holds the Handrail (91) near the Uprights (95, 97), feed the Wire Harness (57) in the right 2 Handrail down into the right Upright. Pull the end of the 89 Wire Harness out of the lower end of the right Upright. If there is a wire tie on the end of the Wire Harness, re- 86 move it. Set the Handrail on the Uprights. Finger tighten four Handrail Bolts (99) into the Uprights (95, 97) and the Handrail (91). Do not tighten the Handrail Bolts yet. Be careful to avoid pinching the Wire Harness (57). Note: The CD Holder (86) and the Cup Holder (85) are replaceable. If these parts become dislodged from the Console Base (89), simply press them back into place. 99 85 57 97 91 95 3. Connect the Wire Harness (57) in the indicated location. 3 Push all of the excess wire up into the right Upright (95). 95 Make sure that the Wire Harness is fully connected. 57 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
6
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Assembly can be completed using the included
allen wrenches.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
3.
Connect the Wire Harness (57) in the indicated location.
Push all of the excess wire up into the right Upright (95).
Make sure that the Wire Harness is fully connected.
2.
While a second person holds the Handrail (91) near the
Uprights (95, 97), feed the Wire Harness (57) in the right
Handrail down into the right Upright. Pull the end of the
Wire Harness out of the lower end of the right Upright. If
there is a wire tie on the end of the Wire Harness, re-
move it. Set the Handrail on the Uprights.
Finger tighten four Handrail Bolts (99) into the Uprights
(95, 97) and the Handrail (91).
Do not tighten the
Handrail Bolts yet. Be careful to avoid pinching the
Wire Harness (57).
Note: The CD Holder (86) and the Cup Holder (85) are
replaceable. If these parts become dislodged from the
Console Base (89), simply press them back into place.
97
91
86
89
85
99
57
2
1.
Slide the Right and Left Uprights (95, 97) onto the brack-
ets near the front of the Frame (76).
Make sure that the
Uprights are on the correct sides; the indicated holes
must be facing inward.
Raise the Right Upright (95) until the lower hole in the
front of the Upright is aligned with the upper hole in the
bracket on the Frame (76). Thread an Upright Bolt (96)
into the Upright and the bracket.
Do not tighten the
Upright Bolt yet.
Repeat this step with the Left Upright (97).
95
96
96
76
97
57
3
Holes
1
95
95
ASSEMBLY