Olympus D-380 D-380 Reference Manual (4.1MB) - Page 93

The flash does not fire in sequential shooting or, movie mode. Set

Get Olympus D-380 - Camedia 2MP Digital Camera PDF manuals and user guides
UPC - 050332137578
View all Olympus D-380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Troubleshooting The batteries ran out of Replace the batteries with new ones. If the green p.9 power during shooting lamp is blinking, wait until it stops. or while the images were being written to the card. (Only the battery check indicator blinks.) The memory gauge is Wait until there is room in the memory gauge. p.9 full. A write-protect seal is Insert a new card or remove the write-protect p.14 attached to the card. seal. There is a problem with Refer to "Error codes". p.89 the card. The flash does not fire. Possible cause The flash is set to the flash-off mode. The subject is illuminated. Sequential shooting or movie mode is set. Panorama mode is set. Corrective action Select a flash mode other than flash-off. If you want the flash to fire, set the flash to fill-in mode. The flash does not fire in sequential shooting or movie mode. Set in the DRIVE menu. The flash does not fire in panorama mode. Close the lens barrier, then open it again. Ref. Page p.33 p.33 p.32, p.39 p.49 The monitor is not clear. Possible cause Corrective action The brightness is not adjusted properly. Select in the mode menu and then adjust the brightness. The monitor is exposed Block the sunlight with your hand. to direct sunlight. Ref. Page p.81 - Pictures you have already taken do not appear on the monitor. Possible cause Corrective action The power is off. Close the lens barrier, then press to turn the monitor on. The camera is in the shooting mode. Press quickly twice, or close the lens barrier and then press to switch to the playback mode. Ref. Page p.17, p.54 p.54 Troubleshooting 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Troubleshooting
92
Troubleshooting
The batteries ran out of
power during shooting
or while the images
were being written to
the card. (Only the
battery check indicator
blinks.)
Replace the batteries with new ones. If the green
lamp is blinking, wait until it stops.
p.9
The memory gauge is
full.
Wait until there is room in the memory gauge.
p.9
A write-protect seal is
attached to the card.
Insert a new card or remove the write-protect
seal.
p.14
There is a problem with
the card.
Refer to “Error codes”.
p.89
The flash does not fire.
Possible cause
Corrective action
Ref. Page
The flash is set to the
flash-off mode.
Select a flash mode other than flash-off.
p.33
The subject is
illuminated.
If you want the flash to fire, set the flash to fill-in
mode.
p.33
Sequential shooting or
movie mode is set.
The flash does not fire in sequential shooting or
movie mode. Set
in the DRIVE menu.
p.32, p.39
Panorama mode is set.
The flash does not fire in panorama mode. Close
the lens barrier, then open it again.
p.49
The monitor is not clear.
Possible cause
Corrective action
Ref. Page
The brightness is not
adjusted properly.
Select
in the mode menu and then adjust
the brightness.
p.81
The monitor is exposed
to direct sunlight.
Block the sunlight with your hand.
–
Pictures you have already taken do not appear on the monitor.
Possible cause
Corrective action
Ref. Page
The power is off.
Close the lens barrier, then press
to turn the
monitor on.
p.17, p.54
The camera is in the
shooting mode.
Press
quickly twice, or close the lens barrier
and then press
to switch to the playback
mode.
p.54