Onkyo TX-NR509 Owner Manual - Page 41
Sp Config (Speaker Configuration), Subwoofer, Front, Center, Surround, Surround Back - hdmi fix
View all Onkyo TX-NR509 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 41 highlights
Select if the component is connected to an analog audio input. Note • When an HDMI IN is assigned to an input selector in "HDMI Input" (➔ page 40), this input assignment is automatically set to the same HDMI IN. And in addition to the usual inputs (e.g., COAXIAL1, COAXIAL2, etc.), you can also select HDMI inputs. • Available sampling rate for PCM signals from a digital input (optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit. • If you connect a component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to PORT selector. Sp Config (Speaker Configuration) Menu Sp Config Some of the settings in this section are set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 28). Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup. This section explains how to specify which speakers are connected and their sizes. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large (full band). For those Cone diameter with a smaller diameter, specify Small (default crossover 100Hz). The crossover frequency can be changed in "Crossover (Crossover Frequency)" (➔ page 41). Note • These settings are not available in either of the following cases: - a pair of headphones is connected. - the "Audio TV Out" setting is set to "On" (➔ page 48). - "HDMI Ctrl (RIHD)" is set to "On" (➔ page 48) and you're listening through your TV speakers. ■ Subwoofer ` Yes: Select if a subwoofer is connected. ` No: Select if no subwoofer is connected. ■ Front ` Small: ` Large: Select based on the cone diameter. Note • If the "Subwoofer" setting is set to "No", this setting is fixed at "Large" and does not appear. ■ Center*1, Surround*1, Surround Back*1*2*3*4 ` Small: ` Large: Select based on the cone diameter. ` None: Select if no speaker is connected. Note *1 If the "Front" setting is set to "Small", the "Large" option cannot be selected. *2 If the "Surround" setting is set to "None", this setting cannot be selected. *3 If the "Surround" setting is set to "Small", the "Large" option cannot be selected. *4 For "Surround Back", the default is "None". ■ Surround Back Ch ` 1ch: Select if only one surround back speaker is connected. ` 2ch: Select if two (left and right) surround back speakers are connected. Note • If the "Surround Back" setting is set to "None", this setting cannot be selected. ■ Crossover (Crossover Frequency) This setting is advantageous for the speakers that you specified as "Small" in "Sp Config (Speaker Configuration)" (➔ page 41). To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers. `40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz, 120Hz, 150Hz, 200Hz Use the diameter of the smallest speaker in your system when choosing the crossover frequency. Speaker cone diameter Over 8 in. (20 cm) 6-1/2 to 8 in. (16 to 20 cm) 5-1/4 to 6-1/2 in. (13 to 16 cm) 3-1/2 to 5-1/4 in. (9 to 13 cm) Under 3-1/2 in. (9 cm) Crossover frequency 40/50/60 Hz* 70/80/90 Hz* 100 Hz 120 Hz 150/200 Hz* * Choose the setting matching your speaker. Note • For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly. • Choose a higher crossover frequency if you want more sound from your subwoofer. ■ Double Bass This setting is not set automatically by Audyssey 2EQ Room Correction and Speaker Setup (➔ page 28). ` On ` Off Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to En the subwoofer. 41