Optoma W460 W460 User Manual - Page 14

Adjusting the Projected Image, Powering Off the Projector, POWER, Warning Indicator

Get Optoma W460 PDF manuals and user guides View all Optoma W460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

INSTALLATION Powering Off the Projector 1. Press the " " button on the remote control or (POWER) button on the panel of the projector to turn off the projector. First push of button will display the following message on the screen. Press the button again to confirm the shut down. If the button is not pressed, the message will disappear in 5 seconds. 2. The Power LED flashes green (0.5 sec on, 0.5 sec off) and the fans will speed up during shut down cooling cycle. The projector reaches stand-by mode as soon as the Power LED steady red. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press (POWER) button on the panel of the projector or " " on the remote control to restart the projector. 3. Disconnect the power cord from the electrical outlet and the projector only when the projector is in stand-by mode. Warning Indicator ‡‡ When the Lamp LED indicator lights red, the projector will automatically shut itself down. Please contact your local reseller or service center. See page 62. ‡‡ When the Temp LED is on a steady (not flashing) red, the projector will automatically shut itself down. Under normal conditions, the projector can be switched on again after it has cooled down. If the problem persists, you should contact your local dealer or our service center. See page 62. Note: Contact the nearest service center if the projector displays these symptoms. See page 73 for more information. Adjusting the Projected Image Adjusting the Projector's Height The projector is equipped with tilt-adjuster feet for adjusting the image height. To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired angle has been achieved. Note The projector table or stand should be level and sturdy. Position the projector so that it is perpendicular to the screen. For personal safety, please secure the cables properly. 14 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
English
14
INSTALLATION
Powering Off the Projector
1.
Press the “
” button on the remote control or
(
POWER
) button on the panel of the projector to
turn off the projector. First push of button will display the following message on the screen.
Press the button again to confirm the shut down. If the button is not pressed, the message will
disappear in 5 seconds.
2.
The Power LED flashes green (0.5 sec on, 0.5 sec off) and the fans will speed up during shut down
cooling cycle. The projector reaches stand-by mode as soon as the Power LED steady red.
If you wish to turn the projector back on, you must wait until the projector has completed the cooling
cycle and has entered standby mode. Once in standby mode, simply press
(
POWER
) button on
the panel of the projector or “
” on the remote control to restart the projector.
3.
Disconnect the power cord from the electrical outlet and the projector only when the projector is in
stand-by mode.
Warning Indicator
±
When the Lamp LED indicator lights red, the projector will automatically shut itself down. Please
contact your local reseller or service center. See page 62.
±
When the Temp LED is on a steady (not flashing) red, the projector will automatically shut itself down.
Under normal conditions, the projector can be switched on again after it has cooled down. If the
problem persists, you should contact your local dealer or our service center. See page 62.
Note°
Contact the nearest service center if the projector displays these symptoms. See page 73 for more
information.
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with tilt-adjuster feet for adjusting the image height.
To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired angle has been achieved.
Note°
±
The projector table or stand should be level and sturdy.
±
Position the projector so that it is perpendicular to the screen.
±
For personal safety, please secure the cables properly.