Optoma W460 W460 User Manual - Page 62

Other, Projector LED status indicator, Message, Power LED, Green, Temp LED

Get Optoma W460 PDF manuals and user guides View all Optoma W460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

APPENDICES Other The projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Lamp burns out or makes a popping sound ‡‡ When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the lamp" on page 64. Projector LED status indicator Power LED Power LED Temp LED Lamp LED Message Standby State Power on (Warming) Power on & Lamp lighting (Red) Power off (Cooling) Quick Resume (100 secs) Error (Lamp fail) Error (Fan fail) Error (Over Temp) Flashing Flashing Flashing (Green) (Red) Flashing 0.25 sec off 0.25 sec light Flashing 0.5 sec off 0.5 sec ligh Back to Red steady light when cooling fan turns off Flashing 0.25 sec off 0.25 sec light Flashing (Red) Note: ‡‡ ‡‡ Steady light => No light => 62 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
English
62
APPENDICES
Other
The projector stops responding to all controls
±
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
±
When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the “Replacing the lamp” on page 64.
Projector LED status indicator
Message
Power LED
(Red)
Power LED
(Green)
Temp LED
(Red)
Lamp LED
(Red)
Standby State
Power on (Warming)
Flashing
0.25 sec off
0.25 sec light
Power on & Lamp lighting
Power off (Cooling)
Flashing
0.5 sec off
0.5 sec ligh
Back to Red steady
light when cooling
fan turns off
Quick Resume (100 secs)
Flashing
0.25 sec off
0.25 sec light
Error (Lamp fail)
Flashing
Error (Fan fail)
Flashing
Flashing
Error (Over Temp)
Flashing
Note°
±
Steady light =>
±
No light =>