Panasonic BT-LH910GJ Operating Instructions

Panasonic BT-LH910GJ Manual

Get Panasonic BT-LH910GJ PDF manuals and user guides View all Panasonic BT-LH910GJ manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic BT-LH910GJ manual content summary:

  • Panasonic BT-LH910GJ | Operating Instructions - Page 1
    Operating Instructions LCD Video Monitor BT-LH910G Model No. Before operating this product, please read the instructions carefully and save this manual for future use. SS0311HM0 -PS D Printed in Japan ENGLISH VQT3N15
  • Panasonic BT-LH910GJ | Operating Instructions - Page 2
    BY UNSCREWING THEM. No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: • To reduce and used in accordance with the instruction manual, may cause harmful interference to information, please visit Panasonic website: http://www.panasonic.com/environmental or call
  • Panasonic BT-LH910GJ | Operating Instructions - Page 3
    for analog video signals. • Audio signal connecting cables If your apparatus supports AES/ must be attached on cable(s) following instructions in this manual. 3. Performance level The performance level article 9(2) Panasonic Testing Centre Panasonic Service Europe, a division of Panasonic Marketing Europe
  • Panasonic BT-LH910GJ | Operating Instructions - Page 4
    accordance with the manufacturer's instructions. 8) D o not 14) Refer all servicing to qualified service personnel. Servicing is required when the monitor by grabbing the panel. Do not place the monitor face down during transportation to prevent damaging it. Keep it upright. Do not expose the LCD
  • Panasonic BT-LH910GJ | Operating Instructions - Page 5
    configuration 24 2D/3D ASSIST 25 MARKER 25 Types of MARKER 28 VIDEO CONFIG 30 SYSTEM CONFIG 34 Performing AUTO CALIBRATION 36 RESET operation 37 .) ■■Optional units •• VF Cable BT-CS910G About this instruction manual •• This instruction manual refers to BT-LH910G as "this unit." •• The
  • Panasonic BT-LH910GJ | Operating Instructions - Page 6
    to drastic temperature fluctuations, condensation may build up on and inside the LCD screen. This may lower the quality of the screen and may damage turn off the power and wait until the condensation has evaporated. ●●Some video images may appear blurred on the screen. ●●Leaving the unit in a
  • Panasonic BT-LH910GJ | Operating Instructions - Page 7
    monitor for broadcasting and business use that is equipped with a 23 cm (9.0 inch) (effective display area) liquid crystal display. It can be used as a VF (viewfinder) for broadcasting and business cameras made by Panasonic Furthermore, support is video signals can be displayed during SDI and VIDEO
  • Panasonic BT-LH910GJ | Operating Instructions - Page 8
    Selecting Area of Use The unit is shipped with the area of use set to the initial setting (NTSC) state. Before using the unit, select the area of use. When you set the area of use, the factory default setting of the menu item on the right is set to the value that matches the area of use. (For the
  • Panasonic BT-LH910GJ | Operating Instructions - Page 9
    Dimensions Unit: mm(inches) 204 (8-1/16) 20.2 3/8-16UNC*1 (13/16) 3/8-16UNC 46 (1-13/16) 170 (6-11/16) 214.5 (8-7/16) 230 (9-1/16) 195.7 (7-11/16) M3 M3 *1 When the adapter is connected: 1/4-20UNC 118.2 (4-5/8) 98.5 (3-7/8) 183 (7-3/16) 25.5 (1) 78.5 (3-7/8) 65.5 (2-9/16) 11.5(7/16) M3 M3 48
  • Panasonic BT-LH910GJ | Operating Instructions - Page 10
    F-IN-R PEAK/ PHASE VOLUME/ CHROMA BRIGHT CONT./ B.LIGHT BT-LH910 123 1 HEADPHONES output jack (M3 stereo mini jack) : HDMI input YPBPR : Analog component input VF : Viewfinder input (VF-YPBPR / VF-VIDEO) *1 INT SG: Internal chart for adjustment [Color Bar + Grayscale] (page 74)
  • Panasonic BT-LH910GJ | Operating Instructions - Page 11
    Controls and Their Functions (continued) 6 7 4 F-IN-R PEAK/ PHASE VOLUME/ CHROMA BRIGHT CONT./ B.LIGHT BT-LH910 5 8 4 MENU, FUNCTION buttons Use these buttons to display menus, select and adjust settings and confirm menu selections. MENU / FUNCTION1 / FUNCTION2
  • Panasonic BT-LH910GJ | Operating Instructions - Page 12
    FOCUS) / EXPAND (VERTICAL) / OVERLAY (OVERLAY) Knob2 VERTICAL (SHIFT) / MANUAL (CONVERGENCE) / FOCUS-IN-RED (ZOOM FOCUS) / MARKER1 (VERTICAL) / LED above the knob (amber) lights. •• Settings are loaded when the monitor is turned on. However, operating changes cannot be made in the following
  • Panasonic BT-LH910GJ | Operating Instructions - Page 13
    This terminal outputs SDI2 input as is. 14 VIDEO/Y input terminal (BNC) This is the VIDEO signal (component signal) input terminal/Y signal (analog to the VF (viewfinder) terminal of broadcasting and business cameras made by Panasonic. The unit can be used as the viewfinder for such a camera.
  • Panasonic BT-LH910GJ | Operating Instructions - Page 14
    cannot be displayed even if you use a battery with a battery level display function. •• For details on how to attach the V-mount type battery, see the instruction manual supplied with the battery holder. 14
  • Panasonic BT-LH910GJ | Operating Instructions - Page 15
    or injury. The external DC power supply cannot be supplied from the DC output terminal of a Panasonic camera-recorder because the unit requires a current that exceeds the output rating of a Panasonic camera-recorder. •• Use a shield cable with a length of 2 m (6.56 feet) or less for the DC
  • Panasonic BT-LH910GJ | Operating Instructions - Page 16
    Panasonic Camera- VF Video Signals*1 Monitor → Camera VF Communication Camera → Monitor*2 recorder TALLY Indication of YPBPR VIDEO signal format of the camera (page 48). *2 For the settings, refer to the instruction manual of the camera. *3 The ZEBRA information can be set for the camera (page
  • Panasonic BT-LH910GJ | Operating Instructions - Page 17
    stand, make sure to align the protrusions for alignment with the corresponding alignment holes. Alignment hole •• When tilting the monitor, be careful not to trap a hand between the monitor and stand. •• When not using the tilt stand, take care that the unit does not fall over. •• When the
  • Panasonic BT-LH910GJ | Operating Instructions - Page 18
    1. The selected input line (page 10) •• SDI1, SDI2, HDMI, VIDEO, YPBPR, VF-YPBPR/VF-VIDEO, INT SG. 2. Signal format •• "UNSUPPORT SIGNAL" appears if an camera used in combination with the unit. For details, see the instruction manual of the camera. 6. Various displays (lock setting) •• This
  • Panasonic BT-LH910GJ | Operating Instructions - Page 19
    : An item target for adjustment. Gray: An item which cannot be adjusted. Sharpness display •• Indicates the "SHARPNESS H/V" setting value of the "VIDEO CONFIG" menu. •• If no operation is performed for 2 minutes, the setting value is confirmed and the display disappears. SHARPNESS H 30 Function
  • Panasonic BT-LH910GJ | Operating Instructions - Page 20
    On-screen Display (continued) Audio level meter display Channel display Reference point 0 dB point 1 2 3 4 5 6 7 8 SDI1 1080/60i •• A color skeleton bar meter indicates the audio level for SDI signals and HDMI signals. •• The display method of the audio level meter can be set in the
  • Panasonic BT-LH910GJ | Operating Instructions - Page 21
    entire screen) •• CLOSED CAPTION can be displayed when SDI signals and VIDEO signals are input. •• CLOSED CAPTION complies with the following standards. select the type of CLOSED CAPTION, display channel (EIA/CEA-608), and display service (EIA/CEA-708) in the menus. (page 50) Notes: •• The specified
  • Panasonic BT-LH910GJ | Operating Instructions - Page 22
    Menu display [MAIN MENU] 2D/3D ASSIST 2D MARKER VIDEO CONFIG SYSTEM CONFIG VF CONFIG FUNCTION GPI INPUT SELECT DISPLAY menu and press [ENTER]. [MAIN MENU] 2D/3D ASSIST 2D MARKER VIDEO CONFIG SYSTEM CONFIG VF CONFIG FUNCTION GPI INPUT SELECT DISPLAY SETUP CONTROL HOURS
  • Panasonic BT-LH910GJ | Operating Instructions - Page 23
    User data include the following settings. •• Menu settings except "SETUP LOAD/SAVE" and "REMOTE in CONTROL" (including button function settings on the monitor front panel) •• Screen adjustments made with the picture adjusting knob Saving user data 111Press [MENU] to display the MAIN menu. 222Press
  • Panasonic BT-LH910GJ | Operating Instructions - Page 24
    2D/3D ASSIST MARKER VIDEO CONFIG SYSTEM CONFIG GPI3 GPI4 GREEN BLUE BIAS RED GREEN BLUE RESET GPI5 VIDEO FORMAT GPI6 GPI7 SELECT L SELECT R LEVEL METER CH ROOM NTSC SETUP GPI8 SDI1 SDI2 HDMI YPBPR COMPONENT LEVEL VF VIDEO/ YPBPR SIGNAL TYPE WFM/VECTOR POSITION INT SG VECTOR MODE
  • Panasonic BT-LH910GJ | Operating Instructions - Page 25
    Main Menu (continued) 2D/3D ASSIST Setting 2D 3D ASSIST The underlined values are factory preset setting values. Description Switches between 2D mode and 3D assist mode. Operates in 2D mode. Operates in 3D assist mode. If you switch to 3D assist mode, the channel
  • Panasonic BT-LH910GJ | Operating Instructions - Page 26
    Main Menu (continued) Sub menu 4:3 *2*4 Settings OFF 95% 93% 90% 88% 80% USER 85% BACK *2 CENTER *2 NORMAL HALF BLACK OFF ON Description Selects/displays the marker type for when the angle of view of the displayed image is 4:3. No marker display 95 % area marker 93 %
  • Panasonic BT-LH910GJ | Operating Instructions - Page 27
    monitor or camera recorder marker size. Conventional monitor marker size Marker size compliant with the camera recorder (Panasonic SMPTE125M for NTSC and ITU-R BT. 601-5 for PAL. TYPE2: The effective horizontal area meets the EIA-RS170A for NTSC and ITU-R BT. 470-4 for PAL. <
  • Panasonic BT-LH910GJ | Operating Instructions - Page 28
    2:1 marker CNSCO marker (2.35/2.39) The marker is displayed as a vertical dotted line when "UNDER" is selected under "SCAN" in the "VIDEO CONFIG" menu. VISTA marker 2:1 marker CNSCO marker (2.35/2.39) Area marker A dotted line is displayed as the marker. TYPE1 Vertical 93.1 % horizontal
  • Panasonic BT-LH910GJ | Operating Instructions - Page 29
    Main Menu (continued) ■■4:3 marker (Displayed for SD input in 4:3 aspect ratio mode) This marker is displayed as a dotted line. 95 % Area marker 93 % Area marker 90 % Area marker 88 % Area marker 80 % Area marker (Displayed for HD input and SD input in 16:9 ratio mode.) This marker is
  • Panasonic BT-LH910GJ | Operating Instructions - Page 30
    Main Menu (continued) VIDEO CONFIG Sub menu GAMMA SELECT *1 Settings STANDARD FILM STDIO/PST of FILM gamma mode. For VARICAM use Other (Gamma curve image) Brightness OTHER Video Gamma COLOR TEMP. USER 0 - 63 *2 D93 D65 D56 VAR1 VAR2 VAR3 VARICAM Input Level Selects
  • Panasonic BT-LH910GJ | Operating Instructions - Page 31
    30 Sets horizontal outline correction. The item display moves to the lower part of the screen during adjustment. SHARPNESS V *4 0 - 30 Sets video. *6 "SCAN" changes are not reflected in Anamo size display. IP mode "MODE1" performs IP conversion using intra-frame interpolation. This monitor
  • Panasonic BT-LH910GJ | Operating Instructions - Page 32
    Main Menu (continued) ■■WB (WHITE BALANCE) adjustment mode Select "VAR1" to "VAR3" for "COLOR TEMP." in the "VIDEO CONFIG" menu to make "WHITE BALANCE VAR1" to "WHITE BALANCE VAR3" (WB) adjustments. The underlined values are factory preset setting values. Sub menu Settings Description
  • Panasonic BT-LH910GJ | Operating Instructions - Page 33
    Main Menu (continued) ■■GAIN/BIAS RGB direct adjustment mode If you press [ENTER] when the [GAIN] or [BIAS] item is selected in the WHITE BALANCE VAR (1 to 3) menu, the screen switches to the one below and you can use the picture adjusting knobs to directly adjust the RGB while checking the picture.
  • Panasonic BT-LH910GJ | Operating Instructions - Page 34
    sub-window type. Reduces the entire images for both input signals and places them side by side. Cuts out the center of the images for both input signals and places them side by side (the images are shown at their original size).
  • Panasonic BT-LH910GJ | Operating Instructions - Page 35
    the area set in "AREA SETTING". *6 ITU-709 indicates the ITU-R BT.709 standard. ■■CALIBRATION The CALIBRATION function in this unit measures LCD panel characteristics from low to high brightness values and internal monitor processing handles CALIBRATION. CALIBRATION does not rely on image quality
  • Panasonic BT-LH910GJ | Operating Instructions - Page 36
    performed. For details on setup procedures, refer to the CA-210 User's Guide. Compensation x y Lv W 0.296 0.3036 203.4 R 0.6534 calibrated correctly. •• LCD panel characteristics and instrument in values after calibration. In a fine tuning of the monitor, also set GAIN and BIAS for R, G and B
  • Panasonic BT-LH910GJ | Operating Instructions - Page 37
    values. Description Used to select the input line for the VF function of the monitor. (VF function: tally lamps (red and green) lit, zebra displayed, ! input lines. Used to allow control of the tally lamp on the rear of the monitor. Does not light. Lights when TALLY control from a GPI/
  • Panasonic BT-LH910GJ | Operating Instructions - Page 38
    "UNDER SCAN" and "NORMAL SCAN". *1 Sets the split-screen function. The display changes in the following order. SINGLE → FULL/PART → STILL → SINGLE *2 Displays waveform or vector display. For details on the available operation items, refer to page 41.
  • Panasonic BT-LH910GJ | Operating Instructions - Page 39
    Main Menu (continued) Sub menu Settings Description (From the previous page) *3*5 Used to highlight in red the section of the image that is being focused. Used to set the zebra display ON or OFF for the camera. *2*6 Used to set the rear tally ON or
  • Panasonic BT-LH910GJ | Operating Instructions - Page 40
    Main Menu (continued) ■■FUNCTION setting restrictions Under the following conditions, "INVALID FUNCTION" is displayed and the settings cannot be configured. Settings Inoperable Condition or Mode HV DELAY •• SUB WINDOW •• WFM •• PIXEL TO PIXEL •• 3D ASSIST •• When HDMI (640 x 480) input GAMMA
  • Panasonic BT-LH910GJ | Operating Instructions - Page 41
    ON/BLUE ONLY OFF •• GAMMA SELECT GAMMA STANDARD/GAMMA FILM/ GAMMA STDIO/PST •• SD ASPECT 4:3/16:9 •• SCAN NORMAL SCAN/UNDER SCAN •• SUB WINDOW SINGLE/FULL/PART/STILL •• WFM/VECTOR WFM/VECTOR OFF/WFM Y ON/ WFM R ON/WFM G ON/WFM B ON/ VECTOR×1/VECTOR×2S/VECTOR×2/ VECTOR×4/VECTOR×8 •• MARKER MARKER OFF
  • Panasonic BT-LH910GJ | Operating Instructions - Page 42
    Press the button again Before memory (two sub-windows) Press the button again After memory (two sub-windows) Video Video Video Still image Video (Left side is stored in memory.) •• PART Resizes the main window to show only its center to also display a second image (two sub-windows). Press
  • Panasonic BT-LH910GJ | Operating Instructions - Page 43
    Main Menu (continued) ■■"WFM/VECTOR" The "WFM/VECTOR" function enables display of the waveform and vector display. Use "DISPLAY SETUP" in the main menu to select "WFM" and "VECTOR" display. (page 50) Press the button ([FUNCTION1] to [FUNCTION3] (page 39)) to which the "WFM/VECTOR" function has been
  • Panasonic BT-LH910GJ | Operating Instructions - Page 44
    Left Bottom *1 The following settings are disabled in PIXEL TO PIXEL mode. •• Setting "ANAMO" to "ON", and setting "SCAN" to "UNDER" in "VIDEO CONFIG" •• Any "HV DELAY" setting in "FUNCTION" •• "MARKER" display *2 Enabled during "SDI1", "SDI2", "HDMI", "YPBPR" and "VF (VF-YPBPR)" input. ■■"PIXEL
  • Panasonic BT-LH910GJ | Operating Instructions - Page 45
    Main Menu (continued) ■■"CROSS HATCH" If the CROSS HATCH function is used, markers are displayed at regular vertical and horizontal intervals to facilitate, for example, easy composition. The marker line width is 1 dot /1 line and the interval is 80 dots/80 lines or 40 dots/40 lines depending on the
  • Panasonic BT-LH910GJ | Operating Instructions - Page 46
    Main Menu (continued) ■■"FOCUS-IN-RED" When the "FOCUS-IN-RED" function is used, the section that is being focused is displayed in an easy-tounderstand red, making camera focus adjustments easy. Each press of the button ("FUNCTION1" to "FUNCTION3" (page 38)) to which the "FOCUS-IN-RED" has been
  • Panasonic BT-LH910GJ | Operating Instructions - Page 47
    GPI functions Disabled Enabled GPI1 - GPI8 UNDEF MARKER1 ON/OFF MARKER2 ON/OFF MARKER BACK HALF MARKER BACK BLACK CENTER MARKER INPUT SEL. VIDEO INPUT SEL. SDI1 INPUT SEL. SDI2 INPUT SEL. HDMI INPUT SEL. YPBPR INPUT SEL. VF INPUT SEL. INT SG SD ASPECT SCAN R-TALLY G-TALLY
  • Panasonic BT-LH910GJ | Operating Instructions - Page 48
    button.*1 Used to select the format for VIDEO input.*2 NTSC or PAL is selected automatically. NTSC PAL Selects NTSC setup level. Select this function when using 7.5 % setup signals. (Adjusts the interior of the monitor to the 7.5 % setup level to suit
  • Panasonic BT-LH910GJ | Operating Instructions - Page 49
    Main Menu (continued) AUDIO Set the audio output and audio level meter. The underlined values are factory preset setting values. Sub menu Settings Description SELECT L *1 *2 CH1 - CH8 (Factory default: CH1) Selects embedded audio channel output to headphones (L). SELECT R *1 *3 CH1 -
  • Panasonic BT-LH910GJ | Operating Instructions - Page 50
    the closed caption display channel for when CEA-608. CAPTION SERVICE SRV6 SRV5 SRV4 SRV3 SRV2 SRV1 Selects the closed caption display service for when CEA-708. *1 Opens the vector display during SDI signal input. *2 Available during VIDEO input. Closed captions appear as bright lines on line 21
  • Panasonic BT-LH910GJ | Operating Instructions - Page 51
    FUNCTION GPI HOURS MEIDNTIPSEUPRLTASYESLEETCUTP CONTROL Sub menu HOURMESTEeRttings Description OPERATION XXXXXXh *1 Displays the number of hours it has been on. LCD XXXXXXh *1 Displays the number of hours that the backlight has been on. *1 "XXXXXX" indicates up to 262,800 hours (approx
  • Panasonic BT-LH910GJ | Operating Instructions - Page 52
    3D camera to be made. (Half-mirror type supported) SHIFT Overlay Shifts SDI2 (R) image horizontally and 1 Switches the L/R images automatically or manually to enable screen display the convergence point checked. ZOOM FOCUS Side-by-side Enlarges part of an image to enable the focus offset
  • Panasonic BT-LH910GJ | Operating Instructions - Page 53
    3D Assist Mode (continued) •• When a signal on which the LR information is superimposed is input to SDI1 such as when there is an AG-3DA1 connection, that LR information is displayed on the right side of the signal format. If L and R are incorrectly input, the LR information is displayed in
  • Panasonic BT-LH910GJ | Operating Instructions - Page 54
    left or right, discomfort will be felt and stereoscopic vision will become difficult when the mode is set to 3D. Perform a comparison check of the parts of the images outside of the markers. 54
  • Panasonic BT-LH910GJ | Operating Instructions - Page 55
    is for checking the subject's position at a fixed screen position in order to determine the depth position of the main subject. Automatically or manually switch the SDI1 (L) image and SDI2 (R) image and then check the subject's position. Screen: Normal display of one screen MANU L SLOW CONV MODE
  • Panasonic BT-LH910GJ | Operating Instructions - Page 56
    zoom offset on the left and right, which tends to cause eye fatigue. Screen: The L/R 2 screens are shown side-by-side. Expanding the parts that are not in focus makes it easy to check the focus of the left and right cameras. OFF OFF ZOOM ZOOM F-IN-R － FUNC. The
  • Panasonic BT-LH910GJ | Operating Instructions - Page 57
    3D Assist Mode (continued) VERTICAL (Vertical Offset Check) This function enables you to operate two horizontal line markers to check the number of lines between markers in the displayed image and check vertical offset, which tends to cause eye fatigue. Screen: The L/R 2 screens are shown side-by-
  • Panasonic BT-LH910GJ | Operating Instructions - Page 58
    3D Assist Mode (continued) OVERLAY (Parallax Check) This function displays vertical line markers to enable you to check the width of parallax. Overlay display Screen: L/R images are overlaid and shown on one screen, and vertical line markers are shown at 3% intervals across the horizontal image
  • Panasonic BT-LH910GJ | Operating Instructions - Page 59
    *1 *2 GPI MARKER1 *1 *2 GPI MARKER2 *1 *2 MARKER TYPE *1 *2 CROSS HATCH SIZE GAMMA SELECT FILM GAMMA COLOR TEMP. SHARPNESS MODE VIDEO CONFIG SHARPNESS H SHARPNESS V I-P MODE MONO ANAMO *1 *2 SD ASPECT *1 *2 SCAN *1 *2 SUB WINDOW MENU POSITION STATUS DISPLAY BATTERY REMAIN
  • Panasonic BT-LH910GJ | Operating Instructions - Page 60
    CAPTION CC TYPE CAPTION CHANNEL CAPTION SERVICE CONTROL CONTROL LOCAL ENABLE HOURS OPERATION METER LCD PEAKING PHASE IMAGE CHROMA ADJUSTMENT BRIGHT CONTRAST BACKLIGHT *3 *3 *3 *3 *3 *3  *3 *3 *3 *3 *3  *3  *3  640 × HDMI SD HD VIDEO VIDEO VF YPBPR SD HD 480
  • Panasonic BT-LH910GJ | Operating Instructions - Page 61
    GPI CONTROL  GPI1 - GPI8  VIDEO FORMAT NTSC SETUP SDI1 SDI2 HDMI YPBPR COMPONENT LEVEL VF VIDEO/ YPBPR SIGNAL TYPE INT SG SELECT L SELECT  CLOSED CAPTION CC TYPE CAPTION CHANNEL CAPTION SERVICE CONTROL  LOCAL ENABLE  OPERATION  LCD  *1 Can be set but the function
  • Panasonic BT-LH910GJ | Operating Instructions - Page 62
    REMOTE Specifications This monitor permits remote operation via GPI/SERIAL terminal. GPI terminal GPI screen items correspond to the following terminals. Use the GPI menu to assign functions to
  • Panasonic BT-LH910GJ | Operating Instructions - Page 63
    and "MARKER BACK BLACK" are activated at the same time, "MARKER BACK BLACK" has priority. •• INPUT SEL. are prioritized in the order of "INPUT SEL. VIDEO," "INPUT SEL. SDI1," "INPUT SEL. SDI2," "INPUT SEL. HDMI," "INPUT SEL. YPBPR," "INPUT SEL. VF," and "INT SG." •• When "GAMMA SEL. FILM" and "GAMMA
  • Panasonic BT-LH910GJ | Operating Instructions - Page 64
    arrangement and connections. For details on systems using SERIAL, be sure to consult your dealer. External Device Side (Straight) BT-LH910G Side Pin number Signal Pin number Signal SERIAL terminals (9P) 1 N.C. 2 RXD 1 N.C. 2 TXD 3 TXD 3 RXD 4 DTR 4 DSR 5 GND 5 GND 6 DSR
  • Panasonic BT-LH910GJ | Operating Instructions - Page 65
    7 DCW 8 DSD 9 DMK Blue only HV Delay Backlight Cross hatch Cross hatch Size Status display Marker settings Data 0: SDI1 1: SDI2 2: VIDEO 3: YPBPR 5: VF 8: HDMI 9: INT SG CON00-60 : Contrast settings BRI00-60 : Brightness settings CRO00-60 : Chroma settings PHA00-60 : Phase
  • Panasonic BT-LH910GJ | Operating Instructions - Page 66
    setting value BRI: Brightness setting value CRO: Chroma setting value PHA: Phase setting value VOL: Volume setting value Response 0: SDI1 1: SDI2 2: YPBPR 4: VIDEO 7: VF-YPBPR 8: VF-VIDEO 11: HDMI 12: INT SG 00-60 00-60 00-60 00-60 00-60 0: OFF 1: ON 000-100 0: OFF 1: LOW
  • Panasonic BT-LH910GJ | Operating Instructions - Page 67
    /59.94p 22: 1080/50p 23: 720/50p 51: 640×480 (60 Hz) 68: 640×480 (59.94 Hz) 00: NO SIGNAL FF: UNSUPPORT SIGNAL BT-LH910 67
  • Panasonic BT-LH910GJ | Operating Instructions - Page 68
    VF (viewfinder) Specifications 5 1 10 6 15 11 VF Terminal (15P) 12345 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 AJ-HPX3100G (Example) This unit side VF Terminal Pin number Signal 1 PR 2 Y 3 PB 4 N.C. 5 GND 6 PR-GND 7 Y-GND 8 PB-GND 9 ZEBRA-SW 10 GND 11 N.C. 12 VF-
  • Panasonic BT-LH910GJ | Operating Instructions - Page 69
    the camera used in combination with the unit. For details, see the instruction manual of the camera. Maintenance •• To clean the cabinet or surface of dry cloth to finish. Water or similar substances getting inside the monitor can cause a malfunction. •• Never use alcohol, thinner or benzene to clean
  • Panasonic BT-LH910GJ | Operating Instructions - Page 70
    terminal is shared with the VIDEO input terminal) HDMI input: 1 line, HDMI × 1 (Type A) (HDCP supported) EMBEDDED AUDIO supported VIERA Link not supported SDI input: 2 line, BNC × 2 SMPTE274M/296M/259M-C/ITU-R BT.656-4 compliant EMBEDDED AUDIO HD
  • Panasonic BT-LH910GJ | Operating Instructions - Page 71
    Specifications (continued) ■■List of Signal Formats Supported in 2D Mode (: Compatible) Input Signal Format/ Status displays VIDEO VF-VIDEO VF-YPBPR NTSC   PAL   640×480 (59.94Hz) 640×480 (60Hz) 480/59.94i  the 1080/50i marker. *4 RGB444 and SDI422 (12 bit) are not supported. 71
  • Panasonic BT-LH910GJ | Operating Instructions - Page 72
    Specifications (continued) ■■List of Signal Formats Supported in 3D Assist Mode (: Compatible) Input Signal Format/ Status displays 720/50p 720/59.94p 720/60p 1035/59.94i *1 1035/60i *2 1080/23.98PsF
  • Panasonic BT-LH910GJ | Operating Instructions - Page 73
    *4 *1 The frame frequency of 1/1.001 is also supported. *2 The XDS service is not supported. *3 Window Style Only justify LEFT is supported. Only print direction LEFT-TO-RIGHT is supported. Only scroll direction BOTTOM-TO-TOP is supported. Word wrap is not supported. Only the display effect SNAP is
  • Panasonic BT-LH910GJ | Operating Instructions - Page 74
    Specifications (continued) ■■INT SG (Internal chart for adjustment) 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% GRAY YELLOW CYAN 75% 75% 75% GREEN MAGENTA RED 75% 75% 75% BLUE 75% -I WHITE +Q BLACK BLACK BLACK -4% BLACK BLACK +4% 74
  • Panasonic BT-LH910GJ | Operating Instructions - Page 75
    Memo 75
  • Panasonic BT-LH910GJ | Operating Instructions - Page 76
    Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
SS0311HM0 -PS D
Printed in Japan
ENGLISH
Model No.
BT-LH910G
Operating Instructions
LCD Video Monitor
Before operating this product, please read the instructions carefully and save this
manual for future use.
VQT3N15