Home » Panasonic Manuals » Projectors » Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector » Manual Viewer

Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector Operat - Page 162

Accessing from the web browser

View all Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector manuals

Add to My Manuals
Save this manual to your list of manuals

Page 162 highlights

Chapter 4 Settings - [NETWORK] menu ff For the LAN cable between the twisted-pair-cable transmitter and the projector, use a cable that meets the following criteria: gg Conforming to CAT5e or higher standards gg Shielded type (including connectors) gg Straight-through gg Single wire ff The maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100 m (328'1"). It is possible to transmit up to 150 m (492'2") if the twisted-pair-cable transmitter supports the long-reach communication method. If this distance is exceeded, image may be disrupted or a malfunction may occur in LAN communication. ff When laying cables between the twisted-pair-cable transmitter and the projector, confirm that cable characteristics are compatible with CAT5e or higher using tools such as a cable tester or cable analyzer. When a relay connector is used, include it in the measurement. ff Do not use a hub between the twisted-pair-cable transmitter and the projector. ff Do not pull cables forcefully. Also, do not bend or fold cables unnecessarily. ff To reduce the effects of noise as much as possible, stretch out the cables between the twisted-pair-cable transmitter and the projector without any loops. ff Lay the cables between the twisted-pair-cable transmitter and the projector away from other cables, particularly power cables. ff When laying multiple cables, run them side by side along the shortest distance possible without bundling them together. ff After laying the cables, go to the [NETWORK] menu → [DIGITAL LINK STATUS] and confirm that the value of [SIGNAL QUALITY] is displayed in green which indicates normal quality. (x page 157) ff For twisted-pair-cable transmitters of other manufacturers of which the operation has been verified with the projector, visit the Panasonic website (http://panasonic.net/avc/projector/). Note that the verification for devices of other manufacturers has been made for the items set by Panasonic Corporation, and not all the operations have been verified. For operation or performance problems caused by the devices of other manufacturers, contact the respective manufacturers. Accessing from the web browser 1) Start up the web browser on the computer. 2) Enter the IP address set on the projector into the URL entry field of the web browser. 3) Enter the user name and the password. ffThe factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the password is panasonic (lower case). 162 - ENGLISH

Section	Page
Read this first!	5
Chapter 1 Preparation	17
Precautions for use	18
Cautions when transporting	18
Cautions when installing	18
Security	21
DIGITAL LINK	21
Art-Net	22
Early Warning Software	22
Disposal	22
Cautions on use	22
Accessories	24
Optional accessories	25
About your projector	26
Remote control	26
Projector body	28
Preparing the remote control	31
Inserting and removing the batteries	31
When using the multiple projectors	31
Connecting the remote control to the projector with a cable	32
Chapter 2 Getting Started	33
Setting up	34
Installation mode	34
Parts for ceiling mount (optional)	35
Projected image and throw distance	35
Adjusting adjustable feet	45
Attaching/removing the projection lens (optional)	46
Attaching the projection lens	46
Removing the projection lens	47
Connecting	48
Before connecting	48
Connecting example: AV equipment	49
Connecting example: Computers	50
Connecting example using DIGITAL LINK	51
Chapter 3 Basic Operations	53
Switching on/off the projector	54
Connecting the power cord	54
Power indicator	54
Switching on the projector	55
When the initial setting screen is displayed	56
Making adjustments and selections	62
Switching off the projector	63
Projecting	64
Selecting the input signal	64
How to adjust focus, zoom, and shift	64
Adjusting the lens position and focus when the Fixed-focus Lens (Model No.: ET‑D75LE90) is used	65
Setting the lens position	66
Adjustment range by the lens position shift (optical shift)	66
Adjusting the lens mounter when the focus is unbalanced	67
Operating with the remote control	70
Switching the input	70
Using the shutter function	71
Using the on-screen display function	72
Using the automatic setup function	72
Switching the image aspect ratio	72
Using the function button	73
Displaying internal test pattern	73
Using the status function	73
Using the AC voltage monitor function	74
Setting ID number of the remote control	74
Chapter 4 Settings	75
Menu navigation	76
Navigating through the menu	76
Main menu	77
Sub-menu	78
[PICTURE] menu	82
[PICTURE MODE]	82
[CONTRAST]	82
[BRIGHTNESS]	83
[COLOR]	83
[TINT]	83
[COLOR TEMPERATURE]	83
[GAMMA]	85
[SYSTEM DAYLIGHT VIEW]	86
[SHARPNESS]	86
[NOISE REDUCTION]	87
[DYNAMIC CONTRAST]	87
[SYSTEM SELECTOR]	88
sRGB-compliant video	89
[POSITION] menu	90
[SHIFT]	90
[ASPECT]	90
[ZOOM]	91
[CLOCK PHASE]	92
[GEOMETRY]	92
[ADVANCED MENU] menu	95
[DIGITAL CINEMA REALITY]	95
[BLANKING]	95
[INPUT RESOLUTION]	96
[CLAMP POSITION]	96
[EDGE BLENDING]	97
[FRAME RESPONSE]	98
[FRAME CREATION]	99
[FRAME LOCK]	99
[RASTER POSITION]	100
[DISPLAY LANGUAGE] menu	101
Changing the display language	101
[3D SETTINGS] menu	102
[3D SYSTEM SETTING]	102
[3D SYNC SETTING]	102
[3D INPUT FORMAT]	103
[LEFT/RIGHT SWAP]	103
[3D COLOR MATCHING]	103
[3D PICTURE BALANCE]	104
[DARK TIME SETTING]	104
[3D FRAME DELAY]	105
[3D TEST MODE]	105
[3D TEST PATTERN]	105
[SAFETY PRECAUTIONS MESSAGE]	106
[3D SAFETY PRECAUTIONS]	106
[DISPLAY OPTION] menu	107
[COLOR MATCHING]	107
[LARGE SCREEN CORRECTION]	108
[SCREEN SETTING]	108
[AUTO SIGNAL]	109
[AUTO SETUP]	109
[BACKUP INPUT SETTING]	110
[SIMUL INPUT SETTING]	111
[RGB IN]	112
[DVI-D IN]	113
[HDMI IN]	114
[DIGITAL LINK IN]	115
[SDI IN]	117
[ON-SCREEN DISPLAY]	118
[IMAGE ROTATION]	120
[BACK COLOR]	120
[STARTUP LOGO]	120
[UNIFORMITY]	121
[SHUTTER SETTING]	121
[FREEZE]	123
[WAVEFORM MONITOR]	123
[CUT OFF]	124
[PROJECTOR SETUP] menu	125
[PROJECTOR ID]	125
[PROJECTION METHOD]	125
[OPERATION SETTING]	125
[LIGHT OUTPUT]	129
[BRIGHTNESS CONTROL]	130
[STANDBY MODE]	134
[NO SIGNAL SHUT-OFF]	134
[NO SIGNAL LIGHTS-OUT]	134
[INITIAL STARTUP]	135
[STARTUP INPUT SELECT]	135
[DATE AND TIME]	135
[SCHEDULE]	136
[RS-232C]	138
[REMOTE2 MODE]	140
[FUNCTION BUTTON]	140
[LENS CALIBRATION]	140
[LENS MEMORY]	141
[STATUS]	142
[AC VOLTAGE MONITOR]	143
[SAVE ALL USER DATA]	144
[LOAD ALL USER DATA]	144
[INITIALIZE]	144
[SERVICE PASSWORD]	145
[P IN P] menu	146
Using P IN P function	146
[TEST PATTERN] menu	148
[TEST PATTERN]	148
[SIGNAL LIST] menu	149
Registering new signals	149
Renaming the registered signal	149
Deleting the registered signal	149
Protecting the registered signal	150
Expanding signal lock-in range	150
Sub memory	151
[SECURITY] menu	152
[SECURITY PASSWORD]	152
[SECURITY PASSWORD CHANGE]	152
[DISPLAY SETTING]	152
[TEXT CHANGE]	153
[CONTROL DEVICE SETUP]	153
[CONTROL DEVICE PASSWORD CHANGE]	154
[NETWORK] menu	156
[DIGITAL LINK MODE]	156
[DIGITAL LINK SETUP]	156
[DIGITAL LINK STATUS]	157
[NETWORK SETUP]	157
[NETWORK CONTROL]	158
[NETWORK STATUS]	158
[DIGITAL LINK MENU]	159
[Art-Net SETUP]	159
[Art-Net CHANNEL SETTING]	159
[Art-Net STATUS]	160
Network connection	160
Connecting to a twisted-pair-cable transmitter	161
Accessing from the web browser	162
Chapter 5 Maintenance	181
Light source/temperature/filter indicators	182
When an indicator lights up	182
Maintenance/replacement	184
Before performing maintenance/replacement	184
Maintenance	184
Replacing the unit	186
Troubleshooting	187
Self-diagnosis display	189
Chapter 6 Appendix	191
Technical information	192
PJLink protocol	192
Using Art-Net function	193
Control commands via LAN	196
<SERIAL IN>/<SERIAL OUT> terminal	199
<REMOTE 2 IN> terminal	203
Two-window display combination list	204
Control device password	205
Upgrade Kit	205
List of compatible signals	206
Specifications	212
Dimensions	215
Precautions for attaching the Ceiling Mount Bracket	216

Match case Limit results 1 per page

Chapter 4

Settings — [NETWORK] menu

162 - ENGLISH

For the LAN cable between the twisted-pair-cable transmitter and the projector, use a cable that meets the following criteria:

Conforming to CAT5e or higher standards

Shielded type (including connectors)

Straight-through

Single wire

The maximum transmission distance between the twisted-pair-cable transmitter and the projector is 100 m (328'1"). It is possible to

transmit up to 150 m (492'2") if the twisted-pair-cable transmitter supports the long-reach communication method. If this distance is

exceeded, image may be disrupted or a malfunction may occur in LAN communication.

When laying cables between the twisted-pair-cable transmitter and the projector, conﬁrm that cable characteristics are compatible with

CAT5e or higher using tools such as a cable tester or cable analyzer.

When a relay connector is used, include it in the measurement.

Do not use a hub between the twisted-pair-cable transmitter and the projector.

Do not pull cables forcefully. Also, do not bend or fold cables unnecessarily.

To reduce the effects of noise as much as possible, stretch out the cables between the twisted-pair-cable transmitter and the projector

without any loops.

Lay the cables between the twisted-pair-cable transmitter and the projector away from other cables, particularly power cables.

When laying multiple cables, run them side by side along the shortest distance possible without bundling them together.

After laying the cables, go to the [NETWORK] menu

→

[DIGITAL LINK STATUS] and conﬁrm that the value of [SIGNAL QUALITY] is

displayed in green which indicates normal quality. (

page 157)

For twisted-pair-cable transmitters of other manufacturers of which the operation has been veriﬁed with the projector, visit the Panasonic

website (http://panasonic.net/avc/projector/). Note that the veriﬁcation for devices of other manufacturers has been made for the items set

by Panasonic Corporation, and not all the operations have been veriﬁed. For operation or performance problems caused by the devices of

other manufacturers, contact the respective manufacturers.

Accessing from the web browser

Start up the web browser on the computer.

Enter the IP address set on the projector into the URL entry field of the web browser.

Enter the user name and the password.

The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the

password is panasonic (lower case).