Home » Panasonic Manuals » Projectors » Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector » Manual Viewer

Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector Operat - Page 216

Precautions for attaching the Ceiling Mount Bracket

View all Panasonic PT-RS11KU 12 000lm / SXGA / 3-Chip DLP™ Laser Projector manuals

Add to My Manuals
Save this manual to your list of manuals

Page 216 highlights

Chapter 6 Appendix - Precautions for attaching the Ceiling Mount Bracket Precautions for attaching the Ceiling Mount Bracket ffWhen installing the projector to a ceiling, be sure to use the specified optional Ceiling Mount Bracket (Model No.: ET‑PKD520H (for High Ceilings), ET‑PKD520S (for Low Ceilings), ET‑PKD520B (Projector Mount Bracket)). The Ceiling Mount Bracket (Model No.: ET‑PKD520H (for High Ceilings), ET‑PKD520S (for Low Ceilings)) is used in combination with the Ceiling Mount Bracket (Model No.: ET‑PKD520B (Projector Mount Bracket)). ffAttach the drop-prevention set that comes with the Ceiling Mount Bracket. If you need the drop-prevention set (hex bolt with washer (M10 x 40), wire rope: TTRA0143) separately, consult your dealer. ffAsk a qualified technician to do the installation work such as mounting the projector on the ceiling. ffPanasonic takes no responsibility for any damage to the projector resulting from use of the Ceiling Mount Bracket not manufactured by Panasonic or the inappropriate choice of location for installing the Ceiling Mount Bracket, even if the warranty period of the projector has not expired. ffUnused products must be removed promptly by a qualified technician. ffReferring to the following screw holes for ceiling mount diagram, use screws of sufficient length to reach the embedded nuts. ffUse a torque screwdriver or Allen torque wrench to tighten bolts to their specified tightening torques. Do not use electric screwdrivers or impact screwdrivers. ffRead the Installation Instructions of the Ceiling Mount Bracket for details. ffThe model numbers of accessories and optional accessories are subject to change without prior notice. Bottom view Unit: mm Model No. of Ceiling Mount Bracket: ET-PKD520H (for High Ceilings) ET-PKD520S (for Low Ceilings) ET-PKD520B (Projector Mount Bracket) Screw holes for ceiling mount Thread engagement depth M6 27 (1-1/16") Embedded nut (Thread engagement depth) M6 27 (1-1/16") Max. screw hole depth 10 (13/32") Embedded nut Torque: (M6) 4 ± 0.5 N·m 216 - ENGLISH

Section	Page
Read this first!	5
Chapter 1 Preparation	17
Precautions for use	18
Cautions when transporting	18
Cautions when installing	18
Security	21
DIGITAL LINK	21
Art-Net	22
Early Warning Software	22
Disposal	22
Cautions on use	22
Accessories	24
Optional accessories	25
About your projector	26
Remote control	26
Projector body	28
Preparing the remote control	31
Inserting and removing the batteries	31
When using the multiple projectors	31
Connecting the remote control to the projector with a cable	32
Chapter 2 Getting Started	33
Setting up	34
Installation mode	34
Parts for ceiling mount (optional)	35
Projected image and throw distance	35
Adjusting adjustable feet	45
Attaching/removing the projection lens (optional)	46
Attaching the projection lens	46
Removing the projection lens	47
Connecting	48
Before connecting	48
Connecting example: AV equipment	49
Connecting example: Computers	50
Connecting example using DIGITAL LINK	51
Chapter 3 Basic Operations	53
Switching on/off the projector	54
Connecting the power cord	54
Power indicator	54
Switching on the projector	55
When the initial setting screen is displayed	56
Making adjustments and selections	62
Switching off the projector	63
Projecting	64
Selecting the input signal	64
How to adjust focus, zoom, and shift	64
Adjusting the lens position and focus when the Fixed-focus Lens (Model No.: ET‑D75LE90) is used	65
Setting the lens position	66
Adjustment range by the lens position shift (optical shift)	66
Adjusting the lens mounter when the focus is unbalanced	67
Operating with the remote control	70
Switching the input	70
Using the shutter function	71
Using the on-screen display function	72
Using the automatic setup function	72
Switching the image aspect ratio	72
Using the function button	73
Displaying internal test pattern	73
Using the status function	73
Using the AC voltage monitor function	74
Setting ID number of the remote control	74
Chapter 4 Settings	75
Menu navigation	76
Navigating through the menu	76
Main menu	77
Sub-menu	78
[PICTURE] menu	82
[PICTURE MODE]	82
[CONTRAST]	82
[BRIGHTNESS]	83
[COLOR]	83
[TINT]	83
[COLOR TEMPERATURE]	83
[GAMMA]	85
[SYSTEM DAYLIGHT VIEW]	86
[SHARPNESS]	86
[NOISE REDUCTION]	87
[DYNAMIC CONTRAST]	87
[SYSTEM SELECTOR]	88
sRGB-compliant video	89
[POSITION] menu	90
[SHIFT]	90
[ASPECT]	90
[ZOOM]	91
[CLOCK PHASE]	92
[GEOMETRY]	92
[ADVANCED MENU] menu	95
[DIGITAL CINEMA REALITY]	95
[BLANKING]	95
[INPUT RESOLUTION]	96
[CLAMP POSITION]	96
[EDGE BLENDING]	97
[FRAME RESPONSE]	98
[FRAME CREATION]	99
[FRAME LOCK]	99
[RASTER POSITION]	100
[DISPLAY LANGUAGE] menu	101
Changing the display language	101
[3D SETTINGS] menu	102
[3D SYSTEM SETTING]	102
[3D SYNC SETTING]	102
[3D INPUT FORMAT]	103
[LEFT/RIGHT SWAP]	103
[3D COLOR MATCHING]	103
[3D PICTURE BALANCE]	104
[DARK TIME SETTING]	104
[3D FRAME DELAY]	105
[3D TEST MODE]	105
[3D TEST PATTERN]	105
[SAFETY PRECAUTIONS MESSAGE]	106
[3D SAFETY PRECAUTIONS]	106
[DISPLAY OPTION] menu	107
[COLOR MATCHING]	107
[LARGE SCREEN CORRECTION]	108
[SCREEN SETTING]	108
[AUTO SIGNAL]	109
[AUTO SETUP]	109
[BACKUP INPUT SETTING]	110
[SIMUL INPUT SETTING]	111
[RGB IN]	112
[DVI-D IN]	113
[HDMI IN]	114
[DIGITAL LINK IN]	115
[SDI IN]	117
[ON-SCREEN DISPLAY]	118
[IMAGE ROTATION]	120
[BACK COLOR]	120
[STARTUP LOGO]	120
[UNIFORMITY]	121
[SHUTTER SETTING]	121
[FREEZE]	123
[WAVEFORM MONITOR]	123
[CUT OFF]	124
[PROJECTOR SETUP] menu	125
[PROJECTOR ID]	125
[PROJECTION METHOD]	125
[OPERATION SETTING]	125
[LIGHT OUTPUT]	129
[BRIGHTNESS CONTROL]	130
[STANDBY MODE]	134
[NO SIGNAL SHUT-OFF]	134
[NO SIGNAL LIGHTS-OUT]	134
[INITIAL STARTUP]	135
[STARTUP INPUT SELECT]	135
[DATE AND TIME]	135
[SCHEDULE]	136
[RS-232C]	138
[REMOTE2 MODE]	140
[FUNCTION BUTTON]	140
[LENS CALIBRATION]	140
[LENS MEMORY]	141
[STATUS]	142
[AC VOLTAGE MONITOR]	143
[SAVE ALL USER DATA]	144
[LOAD ALL USER DATA]	144
[INITIALIZE]	144
[SERVICE PASSWORD]	145
[P IN P] menu	146
Using P IN P function	146
[TEST PATTERN] menu	148
[TEST PATTERN]	148
[SIGNAL LIST] menu	149
Registering new signals	149
Renaming the registered signal	149
Deleting the registered signal	149
Protecting the registered signal	150
Expanding signal lock-in range	150
Sub memory	151
[SECURITY] menu	152
[SECURITY PASSWORD]	152
[SECURITY PASSWORD CHANGE]	152
[DISPLAY SETTING]	152
[TEXT CHANGE]	153
[CONTROL DEVICE SETUP]	153
[CONTROL DEVICE PASSWORD CHANGE]	154
[NETWORK] menu	156
[DIGITAL LINK MODE]	156
[DIGITAL LINK SETUP]	156
[DIGITAL LINK STATUS]	157
[NETWORK SETUP]	157
[NETWORK CONTROL]	158
[NETWORK STATUS]	158
[DIGITAL LINK MENU]	159
[Art-Net SETUP]	159
[Art-Net CHANNEL SETTING]	159
[Art-Net STATUS]	160
Network connection	160
Connecting to a twisted-pair-cable transmitter	161
Accessing from the web browser	162
Chapter 5 Maintenance	181
Light source/temperature/filter indicators	182
When an indicator lights up	182
Maintenance/replacement	184
Before performing maintenance/replacement	184
Maintenance	184
Replacing the unit	186
Troubleshooting	187
Self-diagnosis display	189
Chapter 6 Appendix	191
Technical information	192
PJLink protocol	192
Using Art-Net function	193
Control commands via LAN	196
<SERIAL IN>/<SERIAL OUT> terminal	199
<REMOTE 2 IN> terminal	203
Two-window display combination list	204
Control device password	205
Upgrade Kit	205
List of compatible signals	206
Specifications	212
Dimensions	215
Precautions for attaching the Ceiling Mount Bracket	216

Match case Limit results 1 per page

Chapter 6

Appendix — Precautions for attaching the Ceiling Mount Bracket

216 - ENGLISH

Precautions for attaching the Ceiling Mount Bracket

When installing the projector to a ceiling, be sure to use the speciﬁed optional Ceiling Mount Bracket (Model

No.: ET-PKD520H (for High Ceilings), ET-PKD520S (for Low Ceilings), ET-PKD520B (Projector Mount

Bracket)). The Ceiling Mount Bracket (Model No.: ET-PKD520H (for High Ceilings), ET-PKD520S (for Low

Ceilings)) is used in combination with the Ceiling Mount Bracket (Model No.: ET-PKD520B (Projector Mount

Bracket)).

Attach the drop-prevention set that comes with the Ceiling Mount Bracket. If you need the drop-prevention set

(hex bolt with washer (M10 x 40), wire rope: TTRA0143) separately, consult your dealer.

Ask a qualiﬁed technician to do the installation work such as mounting the projector on the ceiling.

Panasonic takes no responsibility for any damage to the projector resulting from use of the Ceiling Mount

Bracket not manufactured by Panasonic or the inappropriate choice of location for installing the Ceiling Mount

Bracket, even if the warranty period of the projector has not expired.

Unused products must be removed promptly by a qualiﬁed technician.

Referring to the following screw holes for ceiling mount diagram, use screws of sufﬁcient length to reach the

embedded nuts.

Use a torque screwdriver or Allen torque wrench to tighten bolts to their speciﬁed tightening torques. Do not use

electric screwdrivers or impact screwdrivers.

Read the Installation Instructions of the Ceiling Mount Bracket for details.

The model numbers of accessories and optional accessories are subject to change without prior notice.

Bottom view

Model No. of Ceiling Mount Bracket: ET-PKD520H (for High Ceilings)

ET-PKD520S (for Low Ceilings)

ET-PKD520B (Projector Mount Bracket)

Torque: (M6) 4 ± 0.5 N·m

Screw holes for ceiling mount

Thread engagement depth

Max. screw hole depth

Embedded nut

Embedded nut (Thread engagement depth)

Unit: mm

27 (1-1/16")

10 (13/32")

27 (1-1/16")