Panasonic SCHTB15 SCHTB15 User Guide - Page 25
Advanced operations
View all Panasonic SCHTB15 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 25 highlights
Advanced operations The following settings are unnecessary under general usage conditions of the system. ∫ Changing the dual audio Change the dual audio from main to secondary. 1 Confirm the digital audio output setting on the connected TV or player, etc. is set to "Bitstream". 2 Press and hold [HDMI 1/2] for more than 2 sec. 3 While the indicator of the current setting is flashing, press [HDMI 1/2] to change the setting. A : Main ∫ To turn off the 3D surround effect and clear-mode dialog effect Depending on your preference, it is possible to use only the Dolby Virtual Speaker effect by turning off the 3D surround effect and the clear-mode dialog effect. 1 Press and hold [TV] for more than 2 sec. ≥ The indicator for the current setting blinks for 10 sec. Only Dolby Virtual Speaker is on. B : Secondary (SAP: Secondary Audio Program) 3D surround effect and clear-mode dialog effect are also on. A, B : Main and secondary ≥ The setting works only when the dual audio is available in the audio source. ≥ The setting is maintained until it is changed again. ≥ The same setting is used for [TV] and [HDMI 1/2] audio sources. ∫ Remote control code When other Panasonic devices respond to this system's remote control, change the remote control code on the active subwoofer and the remote control. Preparation ≥ Turn off all other Panasonic products. ≥ Turn on this system. Change the remote control code to code 2: 1 Aim the remote control at this system's remote control sensor. 2 Press and hold [MUTE] and [HDMI 1/2] on the remote control for more than 4 sec. ≥ All the indicators will blink for 10 sec when the code of this system is changed. ≥ The setting is maintained until it is changed again. 2 While the indicator is blinking press [TV] to change the setting. ≥ The setting changes each time [TV] is pressed. ≥ The setting will be reset to on when this system is turned off. ∫ To turn off VIERA Link "HDAVI Control" When "HDAVI Control" compatible equipment does not work well with this system, for example, it is possible to turn off this function as follows: ≥ When VIERA Link is turned off the ARC function is not available. Be sure to connect the optical digital audio cable. (> 19) 1 Press and hold [MUTE] on the remote control and [s VOL] on the active subwoofer for more than 2 sec. 2 After the setting has changed, turn off all the connected devices and then turn them on again. ∫ To reduce the clear-mode dialog effect When the dialog does not sound natural while the volume is set low, for example, it is possible to reduce the dialog enhancing effect as follows: Press and hold [TV] on the remote control and [s VOL] on the active subwoofer for more than 2 sec. ∫ To turn off the volume limitation If a state of the lowered volume disturbs you every time this system turns on, for example, it is possible to turn off this function as follows: Press and hold [MUTE] on the remote control and [VOL r] on the active subwoofer for more than 2 sec. ≥ If this system does not operate after changing the code, repeat steps 1 and 2. ≥ To change the remote control code to code 1, repeat the steps above, but replace [HDMI 1/2] with [TV]. The settings of VIERA Link "HDAVI Control", the clear-mode dialog effect and the volume limitation remain intact even if you switch this system to standby mode. To turn these 3 functions back on, this system must be set back to the factory preset. (> 26) ≥ All the indicators will blink once when the setting is changed. Operations 25 VQT3Q59