Panasonic WJHD316 WJHD309 User Guide

Panasonic WJHD316 - DIGITAL DISK RECORDER Manual

Get Panasonic WJHD316 - DIGITAL DISK RECORDER PDF manuals and user guides View all Panasonic WJHD316 manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic WJHD316 manual content summary:

  • Panasonic WJHD316 | WJHD309 User Guide - Page 1
    Digital Disk Recorders Operating Instructions WJ-HD309 WJ-HD316 Model Nos. ALARM ALARM SUSPEND OPERATE TIMER ERROR ALARM RESET HDD 1 HDD 2 MMOONNIITTOORR21 SHIFT 1 2 3 4 STOP PLAY PAUSE REC-- REC STOP 5 DISK SELECT 9 EL-ZOOM SEQ 67 COPY TEXT 10/0 11 OSD 8 MARK 12 PAN/ TILT ZOOM/
  • Panasonic WJHD316 | WJHD309 User Guide - Page 2
    the user to the presence of important operating and maintenance (servicing) instructions in the obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE permanent record of your purchase to aid identification in the event of theft
  • Panasonic WJHD316 | WJHD309 User Guide - Page 3
    Hard Disk 133 I Setting for Mirroring 137 SERIAL (RS232C) CONNECTOR COMMAND REFERENCE 141 I SERIAL (RS232C) Communication Protocol ...... 141 I Command Format 141 FLOWCHART OF THE SETUP MENU 151 PARAMETERS AND THE DEFAULT SETTINGS OF THE SETUP MENU 152 TROUBLESHOOTING 158 SPECIFICATION 162
  • Panasonic WJHD316 | WJHD309 User Guide - Page 4
    Disk Recorders WJ-HD316/309 are designed for use within a surveillance system and are a combination of a hard disk recorder and a video multiplexer (16-input for the WJ-HD316, 9-input for the WJ-HD309). The digital hard disk recorder is a recording device using a hard disk drive to record camera
  • Panasonic WJHD316 | WJHD309 User Guide - Page 5
    000 - 30 000 hours of operation in case they are used at temperature of 25 °C (77 °F). Replacement costs of the hard disk drives are not covered by the warranty even if it needs to be done within the warranty period. Consult your dealer for servicing. When hard disk drive trouble occurs, replace it
  • Panasonic WJHD316 | WJHD309 User Guide - Page 6
    THESE OPERATING INSTRUCTIONS There are 3 sets of operating instructions for the WJHD316/WJ-HD309 as follows. • Operating Instructions (book, these operating instructions) • Network Operating Instructions (PDF) • Network Setup Instructions (PDF) These "Operating Instructions" contain descriptions
  • Panasonic WJHD316 | WJHD309 User Guide - Page 7
    / GOTO TILT LAST SEARCH PAN/TILT SETUP ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + IRIS LISTED PRESET /AUTO SET BUSY PULL Digital Disk Recorder WJ-HD !2!3 !4 @1 @2 @3 @4 @5 @7 @8 @9 S-VIDEO COPY 2 VIDEO OUT AUDIO OUT #0 @7 @8 @9 S-VIDEO COPY 2 VIDEO OUT AUDIO OUT #0 q Operate Indicator
  • Panasonic WJHD316 | WJHD309 User Guide - Page 8
    selected camera was not available to operate because another user is operating it using a controller or a PC via a network. In this case, wait until this indicator goes off. @2 Arrow Buttons (CDAB) Adjusts zooming/focus, or moves the cursor on the setup menus and the search menu. @3 Set Button (SET
  • Panasonic WJHD316 | WJHD309 User Guide - Page 9
    output audio signal to an external device. Recorded audio will be supplied from this connector during playback. e Video Input Connectors (CAMERA IN 1 - 16 for the WJ-HD316/CAMERA IN 1 - 9 for the WJ-HD309) Connect system cameras or combination cameras to these BNC connectors. A 75 Ω termination is
  • Panasonic WJHD316 | WJHD309 User Guide - Page 10
    supports a refresh rate of 50 Hz. If your VGA monitor does not support 50 Hz (or if you are not sure), then turn off your VGA monitor before turning on WJ-HD316/WJ numbers indicate the default positions of camera title q, time w and event display e. Important: • The SETUP MENU will be displayed
  • Panasonic WJHD316 | WJHD309 User Guide - Page 11
    the WJ-HD316, 1 - 9 for the WJ-HD309) #: Alarm number Note: Refer to page 45 for further information about event types and event actions. I On Monitor 2 (To display live or recorded images) - - q w B q q w - A q w C q The negative circled number q indicates the camera title default position
  • Panasonic WJHD316 | WJHD309 User Guide - Page 12
    Note: When the camera title and the task bar are layered in this mode, only the task bar will be displayed. Mode 2 Displays the status on the main bar,
  • Panasonic WJHD316 | WJHD309 User Guide - Page 13
    reverse at fast speed Recording Indicates that recording is currently being performed : Currently recording Search Indicates that displaying live image: Current time and date When playing recorded image: Time and date when recorded *: During summer time, an asterisk (*) will be displayed
  • Panasonic WJHD316 | WJHD309 User Guide - Page 14
    the HDD SMART: Warning of the HDD malfunction H-METER: Set time for hour-meter (active time of the HDD) warning has passed Camera number (1 - 16 for the WJ-HD316, 1 - 9 for the WJ-HD309) #: Abbreviation that indicates partition nn: Available disk size n: Number of connector that an external recording
  • Panasonic WJHD316 | WJHD309 User Guide - Page 15
    on the "Disk End Mode" page of the "Maintenance" setup menu, the available disk space will not be displayed. Refer to a system administrator for further information. NML: Available disk space of the normal recording area used for manual recording and schedule recording EVT: Available disk space of
  • Panasonic WJHD316 | WJHD309 User Guide - Page 16
    the camera selection buttons ([1] - [10/0] for the WJ-HD316, [1] - [9], [0] for the WJ-HD309). To move the cursor, press the arrow buttons. Use the same method to enter or edit characters attached to images. Refer to page 54 for further information. Notes: • The default user name and password are
  • Panasonic WJHD316 | WJHD309 User Guide - Page 17
    A B) and press the SET button. SETUP MENU Maintenance Switcher Recording Display Event Comm Basic Setup Time & Date User Regist. User Edit User Delete Host Regist. Host Edit Host Delete User Level Save/Load I ADMIN Password ***** I PSD User ADMIN I Auto Login Auto Login User ADMIN I Auto Logout
  • Panasonic WJHD316 | WJHD309 User Guide - Page 18
    SHUTDOWN To shutdown the unit, do the following. When recording is being performed, press the REC button for 2 or more seconds. Recording will stop and the indicator on the REC button will go off. When playback is being performed, press the STOP button. Playback will stop and
  • Panasonic WJHD316 | WJHD309 User Guide - Page 19
    from all the connected cameras will be recorded with the default setting. It is possible to record only images displayed on monitor 2 and the VGA monitor by changing the settings. When recording with higher priority than manual recording is performed, manual recording will not be performed until
  • Panasonic WJHD316 | WJHD309 User Guide - Page 20
    GB x 1) • Recording images from a single camera channel by manual recording • Resolution: FIELD • Color Mode: COLOR STD (The color mode setting is available only using a PC via a network.) • Recording without audio (When recording with audio, disk usage will be at the rate of 79.2 MB per hour.) 20
  • Panasonic WJHD316 | WJHD309 User Guide - Page 21
    will stop automatically. With the default setting, recording will stop automatically after recording for 10 seconds. When "CONTINUE" is selected for "Recording Time" of "Emergency REC" on the SETUP MENU (Recording), press the ALARM RESET button to stop recording. The indicator on the REC button
  • Panasonic WJHD316 | WJHD309 User Guide - Page 22
    recording. The playback images will be displayed on monitor 2 and the VGA monitor. [WJ-HD316] z cx MONITOR1 MONITOR2 R 1234 STOP PLAY PAUSE REC - REC STOP REV FWD R SHIFT SEQ OSD PAN/ GOTO TILT LAST SEARCH 5 6 7 8 ZOOM/ PAN/TILT A-B SLOW SETUP /ESC FOCUS REPEAT - + DISK
  • Panasonic WJHD316 | WJHD309 User Guide - Page 23
    the shuttle ring. Press the SET button while holding the rotated recorded images in multi-screen format (4/7/9/10/13/16 for the WJ-HD316, 4/7/9 for the WJ-HD309). q Press the SHIFT button. The SHIFT indicator will light. w Press a camera selection button (1 - 6 for the WJ-HD316, 1 - 3 for the WJ
  • Panasonic WJHD316 | WJHD309 User Guide - Page 24
    Mark Text display (For the WJ-HD316) (For the WJ-HD309) A - B camera selection button 11 (5 for the WJ-HD309) (TEXT). It is possible to play recorded SETUP/ESC button. w Designate an end point (B) by pressing the A - B REPEAT button during playback. When the start point and the end point are set
  • Panasonic WJHD316 | WJHD309 User Guide - Page 25
    to page 48). Built-in hard disk Normal recording area Event recording area Copy area Recording area for manual recording and normal schedule recording Recording area for event recording and emergency recording Recording area for copying [WJ-HD316] MONITOR1 MONITOR2 R 1234 STOP PLAY PAUSE
  • Panasonic WJHD316 | WJHD309 User Guide - Page 26
    ": • When another user has selected the HDD copy area • When copying is being performed manually in the HDD copy area using a PC via a network v Rotate the jog dial to select a desired recorded image to be played, and press the SET button to determine the selection. TIME&DATE CAMERA REC EVENT TEXT
  • Panasonic WJHD316 | WJHD309 User Guide - Page 27
    SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS LISTED 1 EL-ZOOM LOGOUT LOGOUT PRESET /AUTO 2 13 14 15 16 SET no recorded image after the entered time: When there are images recorded after the entered time, the oldest recorded image
  • Panasonic WJHD316 | WJHD309 User Guide - Page 28
    alarm was detected. VIDEO LOSS: Event recording performed when video loss occurred. MANUAL: Manual recording (Refer to page 19.) SCHEDULE: Schedule recording (Refer to page 105.) Search for only images recorded with text information G Recording Event List Window Camera Channel Time and date
  • Panasonic WJHD316 | WJHD309 User Guide - Page 29
    by marked point> The time when the point was marked will be displayed. The camera channel of the recorded image will be displayed. The recorded image of the displayed camera channel will be played on a single screen. The recording mode also will be displayed. The number of the listed data will be
  • Panasonic WJHD316 | WJHD309 User Guide - Page 30
    DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS LISTED 1 EL-ZOOM LOGOUT LOGOUT PRESET /AUTO 2 13 14 15 16 SET BUSY zz x x z Press the SEARCH button repeatedly until the recording event list window is displayed. TIME&DATE CAMERA MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL
  • Panasonic WJHD316 | WJHD309 User Guide - Page 31
    time range will be listed and displayed. Filter recording events by camera channel CAMERA FILTERING CAMERA 1 2345678 9 10 11 12 13 14 15 16 SET : [ SET ] CANCEL : [ ESC ] Select camera channel numbers (1 - 16 for the WJ-HD316, 1 - 9 for the WJ-HD309) using the arrows button to apply filtering
  • Panasonic WJHD316 | WJHD309 User Guide - Page 32
    and date of events that were recorded when motion was detected. z MONITOR1 MONITOR2 R 123 4 STOP PLAY PAUSE REC - REC STOP REV FWD R PAN/ GOTO TILT LAST SEARCH SHIFT SEQ OSD PAN/TILT SETUP 56 7 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10
  • Panasonic WJHD316 | WJHD309 User Guide - Page 33
    SEQ OSD PAN/TILT SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK recorded in the time range set in step 3, the motion detection area setup window will not be displayed when the SET button is pressed. x Press the SET button. I SELECT CAMERA & DATE CAMERA
  • Panasonic WJHD316 | WJHD309 User Guide - Page 34
    GOTO TILT LAST SEARCH SHIFT SEQ OSD PAN/TILT SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS on the status bar. Note: Depending on the position of the set detection areas, the sensitivity indications of the detection areas may be
  • Panasonic WJHD316 | WJHD309 User Guide - Page 35
    SHIFT SEQ OSD PAN/TILT SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK s/20 s/30 s/40 s/50 s/1 m ⁄3 Press the SET button or the PLAY/PAUSE but- ton to start searching will light and playback of the selected recording will start. Note: It is possible
  • Panasonic WJHD316 | WJHD309 User Guide - Page 36
    GOTO TILT LAST SEARCH SHIFT SEQ OSD PAN/TILT SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 the set period in the specified detection area. A B C D Important: • When images to be searched are recorded with a low recording rate,
  • Panasonic WJHD316 | WJHD309 User Guide - Page 37
    SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS LISTED 1 EL-ZOOM LOGOUT LOGOUT PRESET /AUTO 2 13 14 15 16 SET marking lists, press the camera selection buttons [1] and light, and playback of a recorded image from the selected marked
  • Panasonic WJHD316 | WJHD309 User Guide - Page 38
    OSD PAN/ GOTO TILT LAST SEARCH 5 6 7 8 ZOOM/ PAN/TILT A-B SLOW SETUP /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS LISTED EL-ZOOM LOGOUT PRESET 2 13 14 15 16 /AUTO SET BUSY [WJ-HD309] zx MONITOR1 MONITOR2 R 123 R SHIFT SEQ TEXT OSD 456
  • Panasonic WJHD316 | WJHD309 User Guide - Page 39
    PAN/ GOTO TILT LAST SEARCH 5 6 7 8 ZOOM/ PAN/TILT A-B SLOW SETUP /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS LISTED EL-ZOOM LOGOUT PRESET 2 13 14 15 16 /AUTO SET BUSY x [WJ-HD309] z c MONITOR1 MONITOR2 R 123 R SHIFT SEQ TEXT OSD 456
  • Panasonic WJHD316 | WJHD309 User Guide - Page 40
    sequentially according to the settings performed in advance. [WJ-HD316] MONITOR1 MONITOR2 R 1234 STOP PLAY PAUSE REC - REC STOP REV FWD R SHIFT SEQ OSD PAN/ GOTO TILT LAST SEARCH 5 6 7 8 ZOOM/ PAN/TILT A-B SLOW SETUP /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK
  • Panasonic WJHD316 | WJHD309 User Guide - Page 41
    /TILT SETUP 56 7 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS LISTED EL-ZOOM LOGOUT LOGOUT PRESET /AUTO 2 13 14 15 16 SET BUSY c Press the camera selection button ([1] - [16] for the WJ-HD316, [1] - [9] for the WJ-HD309) respective
  • Panasonic WJHD316 | WJHD309 User Guide - Page 42
    to close the iris. Press the arrows button (B) to open the iris. To reset the set iris, press the SET button. c Press the camera selection button ([1] - [16] for the WJ-HD316, [1] - [9] for the WJ-HD309) respective to the controlled camera channel to quit the iris operation. I Preset Action Moves
  • Panasonic WJHD316 | WJHD309 User Guide - Page 43
    DISK SELECT COPY MARK 789 EL-ZOOM LOGOUT 2 0 c STOP PLAY PAUSE REC - REC STOP REV FWD PAN/ GOTO TILT LAST SEARCH PAN/TILT SETUP ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + IRIS LISTED PRESET /AUTO SET BUSY vv c c Press a camera selection button ([1] - [10/0] for the WJ-HD316
  • Panasonic WJHD316 | WJHD309 User Guide - Page 44
    . In this case, perform the settings using the setup menu of camera. MONITOR1 MONITOR2 R 123 4 STOP PLAY PAUSE REC - REC STOP REV FWD R PAN/ GOTO TILT LAST SEARCH SHIFT SEQ OSD PAN/TILT SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10
  • Panasonic WJHD316 | WJHD309 User Guide - Page 45
    -  tor on the rear panel of this unit (Alarm signal output). Records the event log.   * Transmits images to an  FTP server -  : Applicable - : Not applicable * : Available only when using a PC via a network (Refer to the Network Setup Instructions (PDF) for further information.) 45
  • Panasonic WJHD316 | WJHD309 User Guide - Page 46
    automatically. G Moves a camera to the preset position A camera will move to the preset position registered in advance. G Announces an event occurrence by sending e-mails E-mails will be sent to addresses registered in advance. Refer to the Network Operating Instructions (PDF) on the provided CD
  • Panasonic WJHD316 | WJHD309 User Guide - Page 47
    when configuring the system. However, images and event logs will be recorded even when alarm actions are suspended. MONITOR1 MONITOR2 STOP PLAY PAUSE REC - REC STOP TIMER 123 4 M ERROR D ALARM RESET SHIFT SEQ OSD 567 8 DISK SELECT COPY TEXT MARK PAN/ TILT ZOOM/ FOCUS GOTO LAST
  • Panasonic WJHD316 | WJHD309 User Guide - Page 48
    same number of cameras and designating the same recording duration. [WJ-HD316] MONITOR1 MONITOR2 R 1234 STOP PLAY PAUSE REC - REC STOP REV FWD R SHIFT SEQ OSD PAN/ GOTO TILT LAST SEARCH 5 6 7 8 ZOOM/ PAN/TILT A-B SLOW SETUP /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT
  • Panasonic WJHD316 | WJHD309 User Guide - Page 49
    be performed in the following order: Viewer Software → Images → Audio Depending on the set time range for "PERIOD", some of images and audio may not be copied. • Use the viewer software to play the copied images. Refer to the Network Operating Instructions (PDF) for descriptions of how to play the
  • Panasonic WJHD316 | WJHD309 User Guide - Page 50
    Log LIVE v Press the SET button. The cursor will be displayed on the "Data Delete" menu. 316 SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System REC Rate Disk Info Version Info Disk End Mode Disk Capacity Data Delete I Auto Delete OFF I Manual Delete for Normal
  • Panasonic WJHD316 | WJHD309 User Guide - Page 51
    " using the arrows button and press the SET button. SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System REC Rate Disk Info Version Info Disk End Mode Disk Capacity Data Delete I Auto Delete OFF I Manual Delete for Normal Recording Area Delete before 01 . JAN . 03
  • Panasonic WJHD316 | WJHD309 User Guide - Page 52
    Log LIVE v Press the SET button. The cursor will be displayed on the "Data Delete" menu. 316 SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System REC Rate Disk Info Version Info Disk End Mode Disk Capacity Data Delete I Auto Delete OFF I Manual Delete for Normal
  • Panasonic WJHD316 | WJHD309 User Guide - Page 53
    GOTO TILT LAST SEARCH SHIFT SEQ OSD PAN/TILT SETUP 567 8 ZOOM/ A-B SLOW /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 but- ton and press the SET button to start formatting. To stop formatting, select "CANCEL" and press the SET button. During formatting, the
  • Panasonic WJHD316 | WJHD309 User Guide - Page 54
    the recording event list window [WJ-HD316] cv SETUP /ESC FOCUS REPEAT - + DISK SELECT COPY TEXT MARK 9 10/0 11 12 IRIS LISTED EL-ZOOM LOGOUT PRESET 2 13 14 15 16 /AUTO SET BUSY x [WJ 01ch REC EVT MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL MANUAL TEXT ABCDEFGHIJ
  • Panasonic WJHD316 | WJHD309 User Guide - Page 55
    15 16 /AUTO SET BUSY b [WJ-HD309] nb MONITOR1 MONITOR2 R 123 R SHIFT SEQ TEXT OSD 456 DISK SELECT COPY MARK 789 SET button to apply the edited char- acters. TEXT INFORMATION Digital Disc Recorder WJ-HD316 EDIT : [TEXT] SET : [SET] CANCEL : [ESC] To cancel the edit, press the SETUP
  • Panasonic WJHD316 | WJHD309 User Guide - Page 56
    -* Status Error W-ERROR Error SMART Warning H-METER Warning 56 Description Recorded image has been altered. Playback will be paused. Failed to write data on the HDD. The hard disk may be malfunctioning and may not work correctly. The set time for the HOUR METER has passed. (Refer to page 94
  • Panasonic WJHD316 | WJHD309 User Guide - Page 57
    is reduced after the available disk space has reached the set value. Refer to page 95 for descriptions of how to set the available disk space (Disk Capacity) warning. For further information about mail notification of available disk space warning, refer to the Network Setup Instructions (PDF). 57
  • Panasonic WJHD316 | WJHD309 User Guide - Page 58
    Open/Close the SETUP MENU WJ-HD316/WJ-HD309 SETUP /ESC Select an item Change the set parameter Change the cursor position REV FWD - + Rotate the jog dial SET Press a button on the pop-up menu SET Return to the previous menu SETUP /ESC Summer time OFF Set on the SETUP MENU Summer
  • Panasonic WJHD316 | WJHD309 User Guide - Page 59
    Item Close the search window Alarm reset Alarm suspension WJ-HD316/WJ-HD309 SETUP /ESC ALARM RESET ALARM + RESET SET Manual recording Stop manual recording Stop playback/manual recording Play REC - REC STOP REC - REC STOP Press for 2 seconds or more - PLAY PAUSE STOP Stop playback Play at
  • Panasonic WJHD316 | WJHD309 User Guide - Page 60
    LAST Filtering off IRIS LISTED Filtering on Mark a point (For the WJ-HD316) Mark a point (For the WJ-HD309) Select the normal recording area/event recording area of the HDD (For the WJHD316) Select the normal recording area/event recording area of the HDD (For the WJHD309) Select the copy area
  • Panasonic WJHD316 | WJHD309 User Guide - Page 61
    WJ-HD316) Select a camera (For the WJ-HD309) Select a multi-screen (For the WJ-HD316) WJ-HD316/WJ-HD309 SHIFT + SEQ 7 WV-CU360C SEQUENCE SHIFT + 4&2 4 Camera selection buttons (1 - 16) Camera selection buttons (1 - 9) SHIFT + 1 SEQUENCE Camera number Camera number CAM → SET CAM → SET
  • Panasonic WJHD316 | WJHD309 User Guide - Page 62
    It is possible to perform the settings or operate the unit using a web browser installed on a PC when this unit is connected to a network. The available features and the system requirements of a PC are as follows. Refer to the Network Operating Instructions (PDF) on the provided CD-ROM. I Features
  • Panasonic WJHD316 | WJHD309 User Guide - Page 63
    2" for all of the WJ-HD316/309 in the cascade connection. • Video output signal will not be SETUP /ESC - LISTED SET BUSY REV FWD First unit PULL + Digital Disk Recorder WJ-HD ALARM ALARM SUSPEND OPERATE TIMER ERROR ALARM RESET HDD 1 HDD 2 MONITOR1 MONITOR2 1234 SHIFT SEQ OSD 5678 DISK
  • Panasonic WJHD316 | WJHD309 User Guide - Page 64
    INSTALLATION IN THE RACK 1. Remove the rubber legs (6 pcs.) on the bottom of the unit. • Use a flat-blade screwdriver and remove the screws. 2. Install the rack mounting brackets on both sides of the unit. • Using the mounting screws (4 pcs.) for the rack mounting brackets, fix them firmly. Remove
  • Panasonic WJHD316 | WJHD309 User Guide - Page 65
    who access this unit via a network such as a LAN. Up to 32 users and 8 hosts can be registered. The following information can be registered as user information and host information. Item User name Host IP address Password Level Priority Default screen Camera partitioning Description Note Name of
  • Panasonic WJHD316 | WJHD309 User Guide - Page 66
    accessing the unit using a PC via a network, the unit will work as follows according to the setting for "User Authentication" and "Host Authentication" of "NW Setup 1". Setting for "User Authentication" OFF ON OFF ON Setting for "Host Authentication" OFF OFF ON ON User/Host to log in Note Log
  • Panasonic WJHD316 | WJHD309 User Guide - Page 67
    information about the user name and password. Notes: • With the default setting, the disk space is set as the normal recording area. Perform the settings for each recording area according to your needs. • The default user name and password are as follows: User name: ADMIN Password: 12345 • To
  • Panasonic WJHD316 | WJHD309 User Guide - Page 68
    Disk Life Time I HDD Safety Mode 3000h ON b Press the SETUP/ESC button for 2 seconds or more. The SETUP MENU will be closed. The unit will restart automatically and the HDD SAFETY MODE window will be displayed. The HDD safety mode will begin. The camera selection buttons (1 - 16 for the WJ-HD316
  • Panasonic WJHD316 | WJHD309 User Guide - Page 69
    below) will be displayed. The camera selection buttons on the front panel (1 - 16 for the WJ-HD316, 1 - 9, 0 for the WJ-HD309) will light green and disk of the optional extension unit. Refer to the operating instructions of the extension unit for the descriptions of how to replace the hard disk
  • Panasonic WJHD316 | WJHD309 User Guide - Page 70
    . • When connecting combination cameras, connect them to the video input connectors 1 - 8 when using the WJ-HD316 or 1 6 when using the WJ-HD309 (for coaxial communication). G Examples of connections Monitor 1 Monitor 2 Microphone Amplifier Mode switch setting (Factory default) ON 12345678 Note
  • Panasonic WJHD316 | WJHD309 User Guide - Page 71
    ) to prevent disconnection or unstable connections that may cause recording failures or an unstable system. How to fix the cable 7 IN OUT 16 15 14 13 12 11 10 9 8 7 VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 WJ-HDE300 series) 71
  • Panasonic WJHD316 | WJHD309 User Guide - Page 72
    that may cause recording failures or an unstable SETUP ALARM SUSPEND ALARM RESET 567 8 DISK SELECT COPY TEXT MARK ZOOM/ FOCUS A-B SLOW REPEAT /ESC - + 9 10/0 11 12 IRIS LISTED OPERATE HDD 1 EL-ZOOM LOGOUT LOGOUT PRESET /AUTO HDD 2 13 14 15 16 SET BUSY S-VIDEO COPY 2 VIDEO
  • Panasonic WJHD316 | WJHD309 User Guide - Page 73
    SUSPEND ALARM RESET 567 8 DISK SELECT COPY TEXT MARK ZOOM/ FOCUS A-B SLOW REPEAT /ESC - + 9 10/0 11 12 IRIS LISTED OPERATE HDD 1 EL-ZOOM LOGOUT LOGOUT PRESET /AUTO HDD 2 13 14 15 16 SET BUSY S-VIDEO COPY 2 VIDEO OUT AUDIO OUT AUDIO IN VTR S-VIDEO IN connector VIDEO IN
  • Panasonic WJHD316 | WJHD309 User Guide - Page 74
    the respective operating instructions for the descriptions of how to terminate. Termination of this unit can be set with the VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 1 SIGNAL GND POWER AC IN "PS·Data setup" of "Comm" on the SETUP
  • Panasonic WJHD316 | WJHD309 User Guide - Page 75
    DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 1 SIGNAL GND POWER AC IN "PS·Data setup" of "Comm" on the SETUP MENU • Unit Address (System) : 1 • Unit Address (Controller) : 1 RS485 cable POWER ON OFF UNIT 901 1 ALARM RESET SUSPEND SET UP SET ESC ALARM ALARM
  • Panasonic WJHD316 | WJHD309 User Guide - Page 76
    OUT 16 15 14 13 12 11 10 9 8 7 VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 1 SIGNAL GND POWER AC IN Unit Address settings of "PS·Data Setup" of "Comm" on the SETUP MENU First unit (this unit) System : 1 Controller : 1 BNC
  • Panasonic WJHD316 | WJHD309 User Guide - Page 77
    OUT 16 15 14 13 12 11 10 9 8 7 VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 1 SIGNAL GND POWER AC IN Unit Address settings of "PS·Data Setup" of "Comm" on the SETUP MENU First unit (this unit) System : 1 Controller : 2 BNC
  • Panasonic WJHD316 | WJHD309 User Guide - Page 78
    VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 1 SIGNAL GND POWER AC IN Unit Address settings of "PS·Data Setup" of "Comm" on the SETUP ALARM RESET SUSPEND SET UP SET ESC ALARM ALARM SUSPEND 2 3 4 Data Multiplex Unit WJ-MP204 78
  • Panasonic WJHD316 | WJHD309 User Guide - Page 79
    OUT 16 15 14 13 12 11 10 9 8 7 VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 1 SIGNAL GND POWER AC IN Unit Address settings of "PS·Data Setup" of "Comm" on the SETUP MENU First unit (this unit) System : 1 Controller : 2 BNC
  • Panasonic WJHD316 | WJHD309 User Guide - Page 80
    Refer to the respective operating instructions for the descriptions of how to terminate. Termination of this unit can be set with the mode switch on the rear panel. • When connecting an RS485 camera, it is necessary to set each item of "RS485 Setup" of "Comm" on the SETUP MENU according to the RS485
  • Panasonic WJHD316 | WJHD309 User Guide - Page 81
    8 7 IN OUT 16 15 14 13 12 11 10 9 8 7 VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 Termination: Termination: ON OFF OFF OFF Connect the RS485 camera to Switches required to be set RS485 (1) RS485 (2) No.2 No.3 No.5 No.6
  • Panasonic WJHD316 | WJHD309 User Guide - Page 82
    the switch No.5 and No.6 to ON. • For 4-wire communication Connected to the RS485 (CAMERA) port 1: Set the switch No.2 and No.3 to OFF. Connected to the RS485 (CAMERA) port 2: Set the switch No.5 and No.6 to OFF. I RS485 Port DATA G TA TB RA RB G N N D Output Input D Internal block diagram
  • Panasonic WJHD316 | WJHD309 User Guide - Page 83
    alarm output NC Alarm reset input !2 Emergency recording input !3, !4 Earth (Grounding) Alarm output for available !5 disk space of device con WJ-HD316 (Not available for the WJ-HD309) Remarks Open collector output 24 V max., 100 mA Canceling the alarm display Starting emergency recording disk
  • Panasonic WJHD316 | WJHD309 User Guide - Page 84
    G Connection for emergency recording When the external switch is turned ON, emergency recording will be started. Resolution, recording time, recording rate and quality for emergency recording can differ according to the settings of "Emergency REC" of "Recording" on the SETUP MENU. (Refer to page 99
  • Panasonic WJHD316 | WJHD309 User Guide - Page 85
    Alarm output Alarm reset output Alarm recording During recording Disk Buzzer output System error output Temperature error output Time adjust output Series recording output G Connection for the Auto Adjust Time function • When "Auto Adjust Time" of "System" on the SETUP MENU is set to "MASTER" "Time
  • Panasonic WJHD316 | WJHD309 User Guide - Page 86
    from a power outage. When a signal is supplied to the outage detection I/O terminals from the uninterruptible power system (UPS), internal processing (stops recording safely) will be started to shut off the power supply for this unit. After completing the internal processing, a signal will be
  • Panasonic WJHD316 | WJHD309 User Guide - Page 87
    configuration. Pin Configuration !3 q ALARM @5 !4 The pin array is different from other disk recorders. Make sure that the connection is correct by referring to the following. Pin No setting. Non-voltage make contact input/ -100 mA, 5 V pull-up Only for the WJ-HD316 (Not available for the WJ
  • Panasonic WJHD316 | WJHD309 User Guide - Page 88
    SETUP MENU Alarm reset input 100 ms or more Emergency recording input 100 ms or more Alarm output for available disk space of While the size of the available disk device connected to the copy port space is less than the set size HDD error output Until the HDD error is cleared Camera error
  • Panasonic WJHD316 | WJHD309 User Guide - Page 89
    on the SETUP MENU for the communication functions. (Page 118) G Pin Configuration Serial connector of this unit D-sub Pin 9 (Female) Personal computer side D-sub Pin 9 (Female) (Locally procured) 7 (RTS) 8 (CTS) 3 (TXD) 5 (GND) 2 (RXD) 7 (RTS) 8 (CTS) 3 (TXD) 5 (GND) 2 (RXD) WJ-HD316/WJ-HD309
  • Panasonic WJHD316 | WJHD309 User Guide - Page 90
    recording mode and image quality for each 94 camera channel in list form. Display hard disk information such as the available disk space on the built-in hard 94 disk and the connected optional extension unit. Display version information of the software and the hardware and the MAC 94 address. Set
  • Panasonic WJHD316 | WJHD309 User Guide - Page 91
    the settings for the user registration and the user authentication such as 123 user name, password and operational level. Edit the registered user information. 124 Delete registered users. 124 Register the hosts (PCs access this unit via a network) with their information such 124 as IP address
  • Panasonic WJHD316 | WJHD309 User Guide - Page 92
    on the connected monitor, flickering may occur when displaying the SETUP MENU. In this case, it is recommended to use the VGA monitor or a dirtectly connected PC using a LAN cable to perform the settings. (Refer to the Network Setup Instructions (PDF) for descriptions of how to connect this unit and
  • Panasonic WJHD316 | WJHD309 User Guide - Page 93
    seconds or more to apply the settings. The SETUP MENU will be closed. → Live images will be displayed again. SETUP MENU Maintenance Switcher Recording Display Event Comm REC Setup Emergency REC I Recording I Power ON Manual REC I Manual Recording Channel I Embedded REC(Title) I Embedded REC
  • Panasonic WJHD316 | WJHD309 User Guide - Page 94
    to perform the settings for the hour-meter (the active time of the HDD) warning and for the HDD safety mode with this menu. SETUP MENU Maintenance Switcher Recording Display REC Rate Disk Info Version Info Disk End Mode Disk Capacity Data Delete I Software I Hardware (M) (V) I Mac Address
  • Panasonic WJHD316 | WJHD309 User Guide - Page 95
    HDD copy area will not be deleted. 8 Manual Delete for Normal Recording Area By setting the time and date, images in the normal recording area of the hard disk that were recorded up until a day before the set time and date will be deleted. Enter a 2-digit number for the year when entering the time
  • Panasonic WJHD316 | WJHD309 User Guide - Page 96
    LIVE COM: Command alarm EMR: Emergency recording LOSS: Video loss TRM: Terminal alarm VMD: SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System LIVE REC Rate Disk Info Version Info Disk End Mode Disk 03 11:24:11 PM H.METER MAIN1-1 007 25.MAR. the camera channel number
  • Panasonic WJHD316 | WJHD309 User Guide - Page 97
    the access log The time, user name and IP addresses when logging in/out to/from this unit will be displayed in list form. SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System LIVE REC Rate Disk Info Version Info Disk End Mode Disk Capacity Data Delete Event Log Error
  • Panasonic WJHD316 | WJHD309 User Guide - Page 98
    REC CAMERA CAM1 CAM2 CAM3 CAM4 G [REC Setup] Perform the settings for the basic recording. Perform the following settings for the basic recording. SETUP MENU Maintenance Switcher Recording Display Event Comm REC Setup Emergency REC I Recording I Power ON Manual REC I Manual Recording
  • Panasonic WJHD316 | WJHD309 User Guide - Page 99
    ips/4.2 ips/5 ips/6.3 ips/8.3 ips/ 12.5 ips/25 ips/50 ips Important: • When OFF is selected for a specified camera channel, images from a camera channel set to OFF will not be recorded. • When "FRAME 3D ON" or "FRAME 3D OFF" is selected, the total recording rates of CAM 1 - CAM 16 (for the WJ-HD316
  • Panasonic WJHD316 | WJHD309 User Guide - Page 100
    alarm and terminal alarm). SETUP MENU Maintenance Switcher Recording Display Event Comm Event Setup VMD Setup Alarm Setup Terminal Setup I VMD I Video Loss I Terminal/Command Alarm Schedule System SETUP SETUP SETUP LIVE G [VMD Setup] Perform the settings for the motion detection function
  • Panasonic WJHD316 | WJHD309 User Guide - Page 101
    will be named automatically as A, B, C and D in the order of creation. n To complete the settings, rotate the jog dial to select "EXIT" on the status bar, and press the SET button. → The "VMD Setup" window will be closed. G Delete the motion detection area [Screenshot 1] Start operation from the
  • Panasonic WJHD316 | WJHD309 User Guide - Page 102
    an area to be deleted using the arrows button and press the SET button. c To complete the settings, rotate the jog dial to select "EXIT" on the status bar. → The "VMD Setup" window will be closed. 8 Set the sensitivity Set the sensitivity for the created motion detection area. Sensitivity can be
  • Panasonic WJHD316 | WJHD309 User Guide - Page 103
    Reset) Perform the settings to suspend the set duration when the same type of event (motion detection, video loss, terminal alarm, command alarm) has occurred sequentially so that the event action will not be performed each time. (Alarm Disarm) SETUP MENU Maintenance Switcher Recording Display
  • Panasonic WJHD316 | WJHD309 User Guide - Page 104
    in 1 second intervals) G [Terminal Setup] Perform the settings for the alarm terminal polarity. Select how to supply the signal to the alarm terminal. SETUP MENU Maintenance Switcher Recording Display Event Setup VMD Setup Alarm Setup Terminal Setup I Terminal Setup Event Comm Schedule System
  • Panasonic WJHD316 | WJHD309 User Guide - Page 105
    Program 4 Event Comm Schedule System SETUP SETUP SETUP SETUP LIVE 8 Recording Rate for Each Recording Mode Perform the settings of the recording rate for each recording mode (manual recording, schedule recording and event recording). Assign the maximum recording rates according to the resolution
  • Panasonic WJHD316 | WJHD309 User Guide - Page 106
    . Parameters: 0.1 ips/0.2 ips/0.3 ips/0.4 ips/0.5 ips/1 ips/2 ips/3 ips/ 5 ips/6 ips/7.5 ips/10 ips/15 ips/30 ips/60 ips Formula: (Recording rate of each recording mode) - (Recording rate of camera channels whose recording rate is numerically set (ips)) Number of camera channels whose recording rate
  • Panasonic WJHD316 | WJHD309 User Guide - Page 107
    ePnrot gArcatmion1 4 I VMD I Video Loss I Terminal/Command Alarm SETUP SETUP SETUP SETUP SETUP SETUP SETUP O K CANCEL LIVE 8 VMD Perform the settings of event action at a motion detection or the settings of the auto copy function. SETUP MENU Maintenance Switcher Recording Display Event Comm
  • Panasonic WJHD316 | WJHD309 User Guide - Page 108
    Program 2 I Event Program 3 TIermEvineanlt/CPoromgmraamnd4Alarm I Operation Mode I Auto Copy SETUP SETUP SETUP SETUP ALARM OFF OK CANCEL LIVE G [Time Table] Assignment of REC Program and Event Program after setting the time zone Create recording timetables for each day of the week, and assign
  • Panasonic WJHD316 | WJHD309 User Guide - Page 109
    other days of the week. Timetables for special days can be set for up to 30 days. Perform the settings to specify dates as special days and apply the recording schedule to the special days. SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System LIVE Time Table REC Program
  • Panasonic WJHD316 | WJHD309 User Guide - Page 110
    settings for the switcher function of monitor 1. SETUP MENU Maintenance Switcher Recording WJ-HD316): Displays images from camera channels 13 - 16 on a 4-split screen. 1 - 9: Displays images from camera channels 1 - 9 on a 9-split screen. 10 - 16 (only for the WJ-HD316): Displays images from camera
  • Panasonic WJHD316 | WJHD309 User Guide - Page 111
    1". SETUP MENU Maintenance Switcher Recording Display WJ-HD316): Displays images from camera channels 1 - 10 on a 10-split screen. 13SCREEN (only for the WJ-HD316): Displays images from camera channels 1 - 13 on a 13-split screen. 16SCREEN (only for the WJ-HD316): Displays images from camera
  • Panasonic WJHD316 | WJHD309 User Guide - Page 112
    2] Switcher function of monitor 2 Perform the settings for the switcher function of monitor 2. SETUP MENU Maintenance Switcher Recording Display Monitor 1 Monitor 2 I Live Sequence I Sequence Timing I Auto Skip I Login Screen Event Comm Schedule System SETUP INT OFF CAM1 LIVE 8 Live Sequence
  • Panasonic WJHD316 | WJHD309 User Guide - Page 113
    (page 98). Do the following to set the camera title. [Screenshot 1] Start operation from the "OSD Setup" menu. SETUP MENU Maintenance Switcher Recording Display Event Comm OSD Setup Monitor 1 Monitor 2 I Camera Title I Time & Date Display Position I Camera Title Display Position I Line Color on
  • Panasonic WJHD316 | WJHD309 User Guide - Page 114
    be closed. • It is possible to set "Camera Title [Display]" to display a camera title on monitor 2 and "Camera Title [Embedded]" to embed/display a camera title on monitor 1 individually using a PC via a network. Refer to the Network Setup Instruction (PDF) for further information. 8 Time & Date
  • Panasonic WJHD316 | WJHD309 User Guide - Page 115
    OFF: Does not function. G [Monitor2] Settings on monitor 2 display Perform the display settings for monitor 2 such as the display mode (task bar style), time display position on/off, camera title display position, etc. SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System
  • Panasonic WJHD316 | WJHD309 User Guide - Page 116
    for the WJ-HD316, CAM 1 - 9 CH are available for the WJ-HD309) OFF: Does not control camera (CAM 1 - 16 CH are available) G [PS.Data Setup] Settings for the PS·Data Perform the following settings for the PS·Data. SETUP MENU Maintenance Switcher Recording Display Event Comm Camera Control PS
  • Panasonic WJHD316 | WJHD309 User Guide - Page 117
    will be closed. G [RS485 Setup] Settings for RS485 Perform the following settings for RS485. SETUP MENU Maintenance Switcher Recording Display Event Comm Camera Control PS.DATA Setup RS485 Setup RS232C Setup NW Setup 1 NW Setup 2 NTP Setup I Baud Rate I Control Camera CH I Data Bit I Parity
  • Panasonic WJHD316 | WJHD309 User Guide - Page 118
    to change the value for this setting. G [RS232C Setup] Settings for RS232C Perform the following settings for RS232C. SETUP MENU Maintenance Switcher Recording Display Event Comm Camera Control PS.DATA Setup RS485 Setup RS232C Setup NW Setup 1 NW Setup 2 NTP Setup I Unit Address(System) I Baud
  • Panasonic WJHD316 | WJHD309 User Guide - Page 119
    a network such as a LAN. SETUP MENU Maintenance Switcher Recording Display Camera Control PS.Data Setup RS485 Setup RS232C Setup NW Setup 1 NW Setup 2 NTP Setup I DHCP I IP Address I Subnet Mask I Gateway I DNS Primary Secondary I DDNS User Name User Password Access Interval I Host Name HD316
  • Panasonic WJHD316 | WJHD309 User Guide - Page 120
    using "Time Adjustment". G [NTP Setup] Time adjustment of network Perform the following settings for time adjustment. SETUP MENU Maintenance Switcher Recording Display Event Comm Camera Control PS.DATA Setup RS485 Setup RS232C Setup NW Setup 1 NW Setup 2 NTP Setup I Time Adjustment I Time Zone
  • Panasonic WJHD316 | WJHD309 User Guide - Page 121
    Setup] Basic system settings Perform the following settings for basic operation. SETUP MENU Maintenance Switcher Recording Display Event Comm Basic Setup Time & Date User Regist. User Edit User Delete Host Regist. Host Edit Host Delete User Level Save/Load I ADMIN Password ***** I PSD User
  • Panasonic WJHD316 | WJHD309 User Guide - Page 122
    of the date and time Perform the following settings of the time and date. SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System LIVE Basic Setup Time & Date User Regist. User Edit User Delete Host Regist. Host Edit Host Delete User Level Save/Load I Date Format DD.MMM
  • Panasonic WJHD316 | WJHD309 User Guide - Page 123
    MENU Maintenance Switcher Recording Display Event Comm Schedule System LIVE Basic Setup Time & Date User Regist. User Edit User Delete Host Regist. Host Edit Host Delete User Level Save/Load I User Name I User Password I Level I Priority I Default Screen I Camera Partitioning LV1 1 CAM1
  • Panasonic WJHD316 | WJHD309 User Guide - Page 124
    editing. SETUP MENU Maintenance Switcher Recording Display Event Comm Schedule System LIVE Basic Setup Time & Date User Regist. User Edit User Delete Host Regist. Host Edit Host Delete User Level Save/Load I User Name I User Password I Level I Priority I Default Screen I Camera Partitioning
  • Panasonic WJHD316 | WJHD309 User Guide - Page 125
    The default settings are shown as below. SETUP MENU Maintenance Switcher Recording Display Event Comm SChedule System LIVE Basic Setup Time & Date User Regist. User Edit User Delete Host Regist. Host Edit Host Delete User Level Save/Load WJ-HD300 Setup WJ-HD300 Setup Status Camera Setup Event
  • Panasonic WJHD316 | WJHD309 User Guide - Page 126
    be enabled/disabled according to the user level. Function WJ-HD300 Setup WJ-HD300 Setup Status Camera Setup Event Log Status Error Log Status Access Log Status Alarm Reset Alarm Suspend Copy Normal Recording Erase Event Recording Erase Manual REC Operation Playback Operation N/W Access Description
  • Panasonic WJHD316 | WJHD309 User Guide - Page 127
    the WJ-HD316 (4 - 9 for the WJ-HD309) to complete the camera setting. Note: To display the special menu of the camera setup menu, press the camera selection button 2 after moving the cursor to SPECIAL on the camera setup menu. To reset the settings of the camera setup menu to the default settings
  • Panasonic WJHD316 | WJHD309 User Guide - Page 128
    occurrence such as manual recording. Event recording area: An area into which images are recorded at an event occurrence. Copy area: An area into which copy data is stored. It is possible to check the available disk space for each area on "Disk Info" of "Maintenance" on the SETUP MENU. (Refer to
  • Panasonic WJHD316 | WJHD309 User Guide - Page 129
    cause malfunction. • The jumper connector setting differs depending on the models or the manufacturers. Refer to the indication label or the operating instructions of the used hard disk drive. • Attach the connector and the screws firmly. Otherwise, it may cause problems. c After replacing the hard
  • Panasonic WJHD316 | WJHD309 User Guide - Page 130
    window will be displayed. G When replacing the built-in hard disk of the extension unit With displaying the HDD SAFETY MODE window, start replacing the built-in hard disk of the optional extension unit. Refer to the operating instructions of the optional extension unit for the descriptions of how
  • Panasonic WJHD316 | WJHD309 User Guide - Page 131
    optional extension unit will be displayed on the "HDD DISK MENU". Digital Disk Recorder HDD DISK MENU WJ-HD300 TOP MENU FORMAT MIRROR ON MIRROR OFF REMOVE - Information of recording areas : [SETUP/ESC] OK : [SET] EXIT Main unit/optional extension unit Information about hard disk located in the
  • Panasonic WJHD316 | WJHD309 User Guide - Page 132
    is impossible to use two hard disks in this unit. The recorded pictures in those disks will not be deleted. G Setup/cancel the RAID 5 function Do the following to set or cancel the RAID 5 function with an optional extension unit. Refer to the operating instructions of the extension unit for further
  • Panasonic WJHD316 | WJHD309 User Guide - Page 133
    160GB 160GB 160GB - Information of recording areas : [SETUP/ESC] OK : [SET] EXIT c Move the cursor to "FORMAT" using the arrows button (A B) and press the SET button. [Screenshot 2] The password entry window will be displayed. Digital Disk Recorder HDD DISK MENU WJ-HD300 TOP MENU FORMAT MIRROR
  • Panasonic WJHD316 | WJHD309 User Guide - Page 134
    160GB 160GB 160GB - Information of recording areas : [SETUP/ESC] OK : [SET] EXIT c Move the cursor to "FORMAT" using the arrows button (A B) and press the SET button. [Screenshot 2] The password entry window will be displayed. Digital Disk Recorder HDD DISK MENU WJ-HD300 TOP MENU FORMAT MIRROR
  • Panasonic WJHD316 | WJHD309 User Guide - Page 135
    unit is selected, "All Pre REC Area" is not available. [Screenshot 6] The confirmation menu of the set recording area will be displayed. Digital Disk Recorder HDD DISK MENU WJ-HD300 DISK SETTING METHOD AUTO SETUP Normal area 10GB Event area 80GB Copy area 35GB Free area 35GB HDD Total capacity
  • Panasonic WJHD316 | WJHD309 User Guide - Page 136
    is impossible to select the camera channel to which the pre-recording area on another hard disk (extension unit) is already assigned. [Screenshot 8] The "DETAILED SETUP" menu will be displayed. Digital Disk Recorder HDD DISK MENU WJ-HD300 DISK SETTING METHOD DETAILED SETUP Normal area 110GB Event
  • Panasonic WJHD316 | WJHD309 User Guide - Page 137
    160GB 160GB 160GB - Information of recording areas : [SETUP/ESC] OK : [SET] EXIT x Move the cursor to "FORMAT" using the arrows button (A B) and press the SET button. [Screenshot 2] The password entry window will be displayed. Digital Disk Recorder HDD DISK MENU WJ-HD300 TOP MENU FORMAT MIRROR
  • Panasonic WJHD316 | WJHD309 User Guide - Page 138
    160GB 160GB - Information of recording areas : [SETUP/ESC] OK : [SET] EXIT x Move the cursor to "MIRROR OFF" using the arrows button (A B) and press the SET button. [Screenshot 2] The password entry window will be displayed. Digital Disk Recorder HDD DISK MENU WJ-HD300 TOP MENU FORMAT MIRROR
  • Panasonic WJHD316 | WJHD309 User Guide - Page 139
    4 160GB 160GB 160GB 160GB 160GB 160GB - Information of recording areas : [SETUP/ESC] OK : [SET] EXIT c Enter the password for an administrator by rotating the jog dial. The camera selection buttons ([1] - [10/0] for the WJHD316, [1] - [9], [0] for the WJ-HD309) are available to enter numbers for
  • Panasonic WJHD316 | WJHD309 User Guide - Page 140
    recording areas : [SETUP/ESC] OK : [SET] EXIT c Enter the password for an administrator by rotating the jog dial. The camera selection buttons ([1] - [10/0] for the WJHD316, [1] - [9], [0] for the WJ remove of the hard disk is started. Digital Disk Recorder HDD DISK MENU WJ-HD300 TOP MENU REMOVING
  • Panasonic WJHD316 | WJHD309 User Guide - Page 141
    Notes: • This unit does not support the communication converted between the SERIAL ( The setting is available in "SETUP MENU" - "Comm" - " SERIAL (RS232C) Setting". code: 02h) is always prefixed to data. h shows hexadecimal digit. Transmission command: A command shown in the Command List is
  • Panasonic WJHD316 | WJHD309 User Guide - Page 142
    the response command to the PC. Example: These are examples for the following operations. 1. Login with the user name of "ADMIN" and with password of "12345". 2. Display images from camera channel 1 on monitor 2. 3. Start playback from the point of January 1 2003, 3:00 p.m. 4. Logout (1) (This unit
  • Panasonic WJHD316 | WJHD309 User Guide - Page 143
    unit) Logout. [STX]AD001;OLO [ETX] When receiving the command above, the user logged in via SERIAL (RS232C) (ADMIN) will log out. (10) (This Parameter invalid (The number, digit, or range of the command parameters is incorrect.) 003: Command invalid (The unit does not support the operation mode.) E:
  • Panasonic WJHD316 | WJHD309 User Guide - Page 144
    Refer to the following page for cable specification.) D-sub Pin 9 (Female) 3 VIDEO MODE 2 1 COPY 1 DATA 6 5 RS485(CAMERA) 10/100BASE-T EXT STORAGE 4 3 2 1 6 5 4 3 2 1 This unit D-sub Pin 9 (Female) SIGNAL GND POWER AC IN PC 5 1 96 As viewed from the rear of the WJ-HD316/WJ
  • Panasonic WJHD316 | WJHD309 User Guide - Page 145
    Pause during playback Play Manual recording Manual recording with text Stop records: Fixed n=0 OFF n=1 ON n=0 A - B repeat playback OFF n=1 Set repeat start point (A point) n=2 Set repeat end point (B point) yyyymmddhhnnss: Date and time of A/B point n=0 COPY SETUP MENU OFF n=1 COPY SETUP
  • Panasonic WJHD316 | WJHD309 User Guide - Page 146
    (SET) n1n2=P- Go back to an older page (BACK) n1n2=PU Move to upper layer (ESC) yyyymmddhhnn: Date and time n=0 Standard time n=1 Summer time n=0 Normal recording mode n=2 Continuous (External timer) recording mode Parameter (ASCII) uuu...uuu: User name (32-byte fixed length) ppp...ppp: Password
  • Panasonic WJHD316 | WJHD309 User Guide - Page 147
    to specify the camera CH. Fixed to 0 ccc: Camera CH No. of target for data copy m=0 Copy to HDD copy sector m=1 Copy to media connected to COPY 1 m=2 Copy to media connected to COPY 2 k=1 Event input log k=2 Trouble log k=3 Access log k=0 Record list k=1 Event input log k=2 Trouble log k=3 (Access
  • Panasonic WJHD316 | WJHD309 User Guide - Page 148
    request QLD:0 Software version inquiry QRV Status inquiry QSR QID:WJ-HD309 or QID:WJ-HD316 QIB:WJ-HD309 or QIB:WJ-HD316 QIC:2 QLD:n QRV:n.nn QSR:Status 1:Status 2... Parameter (ASCII) n=0 (Search editing area OFF) n=1 (Recording event search list ON) n=2 (Recording event search thumbnail
  • Panasonic WJHD316 | WJHD309 User Guide - Page 149
    nn=Sequence number rrrrrrrrrrrrrrrr: Record number yyyymmddhhnnss: Recording event date and time ccc: Camera CH x=0 Manual recording x=1 Schedule recording x=2 VMD recording x=3 Alarm port recording x=4 Command alarm recording x=5 VIDEO LOSS recording x=6 Emergency recording yyy: Event-activated CH
  • Panasonic WJHD316 | WJHD309 User Guide - Page 150
    command (ASCII) RCK RCK Parameter (ASCII) rrrrrrrrrrrrrrrr: Record number ccc: Camera CH q: picture quality (0 (Very Fine), 1 (Fine), 2 (Normal), 3 (Extended)) nnnn: Recording rate yyyymmddhhnnss: Recording start date and time nnss: Recording total time t=0 Text included t=1 Text not included
  • Panasonic WJHD316 | WJHD309 User Guide - Page 151
    REC Setup Maintenance Disk Info Recording Emergency REC Maintenance Version info Maintenance Disk End Mode Maintenance Disk Capacity Maintenance Disk Delete Maintenance Event Log Event Event Setup Event VMD Setup Event Alarm Setup Event Terminal Setup Event Setup VMD Event Setup Video Loss
  • Panasonic WJHD316 | WJHD309 User Guide - Page 152
    DEFAULT SETTINGS OF THE SETUP MENU These are the setting parameters and the default settings of the items on the SETUP MENU. Refer to these as reference. Setup Menu Maintenance Disk Info Disk End Mode Disk Capacity Data Delete Setup Item Warning for Disk Life Time HDD Safety Mode Normal Recording
  • Panasonic WJHD316 | WJHD309 User Guide - Page 153
    /CAM2/...../CAM9 HD316: OFF/CAM1/CAM2/...../CAM16 HD309: OFF/CAM1/CAM2/...../CAM9 OFF/1 s/2 s/...../30 s/40 s/50 s/1 m/2 m/3 m/ 4 m/5 m 2 s/3 s/...../10 s N.O./N.C. Default Setting VMD: OFF Video Loss: 2 s Terminal Command Alarm: 2 s VMD: OFF Video Loss: Camera channel with a video loss occurrence
  • Panasonic WJHD316 | WJHD309 User Guide - Page 154
    Default Setting --- Live Sequence Sequence Timing Auto Skip Login Screen Secret View Live Sequence Sequence Timing Auto Skip Login Screen [Operating with the buttons of the unit] WJ-HD316: 1/2/.../16/1-4/5-8/9-12/13-16/1-9/10-16/-WJ-HD309: 1/2/.../9/1-4/5-8/9-9/1-9/-[Operating via a network] WJ
  • Panasonic WJHD316 | WJHD309 User Guide - Page 155
    HTTP Port Number User Authentication Host Authentication Line Speed Live Video Quality Video Rate DHCP IP Address Subnet Mask Gateway DNS Primary Secondary DDNS Parameter ON/OFF ON/OFF ON/OFF MODE1/MODE2/MODE3 UPPER/LOWER ON/OFF Default Setting ON ON ON MODE1 LOWER ON S/M/L HD316: CAM1 to CAM8
  • Panasonic WJHD316 | WJHD309 User Guide - Page 156
    Server Address User Name User Password System Basic Setup 156 ADMIN Password PSD User Auto Login Auto Login User Auto Logout Priority "GO TO LAST" before Language Beep (Operation) Buzzer (Error) Shutdown Time Auto Copy Parameter 10 m/30 m/1 h/6 h/24 h - - Default Setting 1 h HD316: HD316 HD309
  • Panasonic WJHD316 | WJHD309 User Guide - Page 157
    Time(Day Light Saving) ON/OFF/AUTO OFF Summer Time(Day Light Saving) Table - - User Name - - Password - - Level 1/2/3 1 Priority 1/2/...../16 1 Default Screen WJ-HD316 CAM1/CAM2/.../CAM16/QUAD1-4/QUAD5-8/ QUAD9-12/QUAD13-16/7SCREEN/9SCREEN1-9/ 9SCREEN10-16/10SCREEN/13SCREEN
  • Panasonic WJHD316 | WJHD309 User Guide - Page 158
    may be sticking to the camera lens. - Cannot open SETUP MENU. 158 • Can the users display the SETUP MENU on the monitors? Refer to p. 123 Check the level settings of the users logging in. and 125. • Check if monitor 1 is used to display the SETUP MENU. The SETUP MENU cannot be displayed on
  • Panasonic WJHD316 | WJHD309 User Guide - Page 159
    Problem Cannot start recording. Cannot record the SETUP MENU of a matrix switcher Cannot playback images. Cannot control cameras. Check item/Remedy • Check if the HDD has any available disk space. • Check if the recording setup is set to ON. • Check the schedule settings. • Check the recording
  • Panasonic WJHD316 | WJHD309 User Guide - Page 160
    operation mode is set to ALARM (alarm mode). Page Refer to p. 83 and 87. Refer to p. 87. Refer to p. 107. • Check the camera connections. Refer to p. 70. • If the camera connections are proper, refer to the dealer. Cable wires may be snapped or the unit may have some - trouble. • Check if
  • Panasonic WJHD316 | WJHD309 User Guide - Page 161
    if the "Disk End Mode" is set to STOP. • Check if there is a partition in the HDD. Refer to p. 95. - Cannot establish a connection via the network. Response or Image update takes time. • Check the network settings of the unit and PC. Refer to the Network Setup Instructions (PDF). • Check the
  • Panasonic WJHD316 | WJHD309 User Guide - Page 162
    SPECIFICATION recording input*2, additional space warning output*3 (for devices connected to copy connectors), HDD trouble output*3, camera trouble output*3, trouble When power is not supplied, the video output signal was not sent from the unit even if a video input signal is supplied. *2 Non-voltage
  • Panasonic WJHD316 | WJHD309 User Guide - Page 163
    : Power Cord 2 Rack Mounting Bracket 2 Screw for Rack Mounting Bracket 4 Cable Clamp 1 Screw for Cable Clamp 1 Hard Disk Drive Fixing Screw 4 *The following are included on the CD-ROM: Viewer software Plug-in software Network Operating Instructions (PDF) Network Setup Operations (PDF) 163
  • Panasonic WJHD316 | WJHD309 User Guide - Page 164
    Matsushita Electric Industrial Co., Ltd. Osaka, Japan http://www.panasonic.co.jp/global/ 2004 © Matsushita Electric Industrial Co., Ltd. All rights reserved. NM0104-2034 3TR001707CAA Printed in Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
WJ-HD309
Model Nos.
WJ-HD316
Digital Disk Recorders
Operating Instructions
－�
＋�
TIMER
ERROR
ALARM
RESET
HDD 1
HDD 2
PULL
ALARM
ALARM
SUSPEND
OPERATE
Digital Disk Recorder
WJ-HD
316
MONITOR1
MONITOR2
SHIFT
DISK SELECT
EL-ZOOM
COPY
TEXT
MARK
PAN/
TILT
ZOOM/
FOCUS
IRIS
LISTED
BUSY
A-B
REPEAT
PAN/TILT
SLOW
SETUP
/ESC
SEARCH
REV
FWD
SET
GOTO
LAST
PRESET
/AUTO
LOGOUT
OSD
SEQ
1
4
7
8
9
11
12
13
14
15
16
10/0
5
2
6
3
-
REC STOP
REC-
STOP
PAUSE
PLAY