Pfaff ClassicStyle 2025 Owner's Manual - Page 29

Changing the needle, Threading the twin needle

Get Pfaff ClassicStyle 2025 PDF manuals and user guides View all Pfaff ClassicStyle 2025 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Technical section Changing the needle Switch off the main switch To remove: Lower the presser foot and set the needle to its highest position. Loosen the needle screw (32) and pull the needle out downwards. To insert: The Áat side A of the needle must face to the rear. Lower the presser foot and insert A the needle, pushing it up as far as it will go. Hold the needle and tighten the needle screw (32) Àrmly. B Threading the twin needle: Replace the sewing needle with a twin needle. Insert the second spool holder and place one spool of thread on each of the spool holders. During threading in the left threading slot (17), make sure that you pass one thread each to the left and right sides of tension disk B. Continue threading in the usual manner, making sure the threads do not become twisted together. Pull the threads right and left into the thread guide and thread the needles (for additional details, see "Embroidering with the twin needle"). Note: It is not possible to use the integrated needle threader with a twin needle. 2:17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
2:17
B
A
Technical section
Changing the needle
Switch off the main switch
To remove: Lower the presser foot and set the needle to its
highest position. Loosen the needle screw (32) and pull the
needle out downwards.
To insert: The
Á
at side A of the
needle must face to the rear.
Lower the presser foot and insert
the needle, pushing it up as far
as it will go. Hold the needle and
tighten the needle screw (32)
À
rmly.
Threading the twin needle:
Replace the sewing needle with a twin needle. Insert the second spool holder and place one spool of thread on each of the
spool holders. During threading in the left threading slot (17), make sure that you pass one thread each to the left and right
sides of tension disk B. Continue threading in the usual manner, making sure the threads do not become twisted together.
Pull the threads right and left into the thread guide and thread the needles (for additional details, see “Embroidering with
the twin needle”).
Note: It is not possible to use the integrated needle threader with a twin needle.