ProForm 14.0 Mme Elliptical English Manual - Page 25

Maintenance And Troubleshooting

Get ProForm 14.0 Mme Elliptical PDF manuals and user guides View all ProForm 14.0 Mme Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

MAINTENANCE AND TROUBLESHOOTING MAINTENANCE Inspect and tighten all parts of the elliptical regularly. Replace any worn parts immediately. Next, locate the Reed Switch (86). Turn the Pulley (53) until a Magnet (88) is aligned with the Reed Switch. To clean the elliptical, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight. CONSOLE TROUBLESHOOTING 86 88 67 If the console does not display your heart rate when you hold the handgrip heart rate monitor, or if the dis- played heart rate appears to be too high or too low, see step 5 on page 19. 7 If a replacement power adapter is needed, call the telephone number on the cover of this manual. IMPORTANT: To avoid damaging the console, use only a manufacturer-supplied regulated power 53 adapter. HOW TO LEVEL THE ELLIPTICAL If the elliptical rocks slightly on your floor during use, see HOW TO LEVEL THE ELLIPTICAL on page 15. HOW TO ADJUST THE REED SWITCH 17 If the console does not display correct feedback, the reed switch should be adjusted. Before adjusting the reed switch, unplug the power adapter. Use a standard screwdriver and pry the Right Rail Cover (7) upward. Next, remove all of the Screws (67, 73) from the Right Outer and Inner Shields (17, 19); there are two sizes of Screws in the Right Outer and Inner Shields-note which size of Screw you remove from each hole. Then, gently remove the Right Outer Shield. Loosen, but do not remove, the two M4 x 16mm Screws (67). Slide the Reed Switch (86) slightly closer to or away from the Magnet (88), and then retighten the Screws. Then, plug in the power adapter and rock the Pulley (53) forward and backward so that the Magnet passes the Reed Switch repeatedly. Repeat these actions until the console displays correct feedback. When the reed switch is correctly adjusted, reattach the right outer and inner shields and the right rail covers. Then, plug in the power adapter. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
25
MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE
Inspect and tighten all parts of the elliptical regularly.
Replace any worn parts immediately.
To clean the elliptical, use a damp cloth and a small
amount of mild soap.
IMPORTANT: To avoid damage
to the console, keep liquids away from the console
and keep the console out of direct sunlight.
CONSOLE TROUBLESHOOTING
If the console does not display your heart rate when
you hold the handgrip heart rate monitor, or if the dis-
played heart rate appears to be too high or too low, see
step 5 on page 19.
If a replacement power adapter is needed, call the
telephone number on the cover of this manual.
IMPORTANT: To avoid damaging the console, use
only a manufacturer-supplied regulated power
adapter.
HOW TO LEVEL THE ELLIPTICAL
If the elliptical rocks slightly on your floor during use,
see HOW TO LEVEL THE ELLIPTICAL on page 15.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. Before adjusting the
reed switch,
unplug the power adapter.
Use a standard screwdriver and pry the Right Rail
Cover (7) upward. Next, remove all of the Screws (67,
73) from the Right Outer and Inner Shields (17, 19);
there are two sizes of Screws in the Right Outer
and Inner Shields—note which size of Screw you
remove from each hole.
Then, gently remove the
Right Outer Shield.
Next, locate the Reed Switch (86). Turn the Pulley (53)
until a Magnet (88) is aligned with the Reed Switch.
Loosen, but do not remove, the two M4 x 16mm
Screws (67). Slide the Reed Switch (86) slightly closer
to or away from the Magnet (88), and then retighten the
Screws. Then, plug in the power adapter and rock the
Pulley (53) forward and backward so that the Magnet
passes the Reed Switch repeatedly. Repeat these
actions until the console displays correct feedback.
When the reed switch is correctly adjusted, reattach
the right outer and inner shields and the right rail cov-
ers. Then, plug in the power adapter.
17
7
88
67
86
53