Ryobi TS1142L User Manual - Page 17

Danger, Warning, Aligning The Laser Guide Line

Get Ryobi TS1142L PDF manuals and user guides View all Ryobi TS1142L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

ASSEMBLY Danger: Laser radiation. Avoid direct eye contact with light source. WARNING: Use of controls or adjustments or performance of procedures other than those specified herein can result in hazardous radiation exposure. aligning the laser guide line See Figures 13 and 14. Lock out the switch trigger by installing a padlock (not included). Draw a line on the workpiece. When the laser guide switch is turned on it will generate a red line on the work surface. This line will let you see your mark and the laser guide line at the same time, and will assist you in lining up the mark for more accurate cutting of the workpiece. Align the laser line and the mark with the blade at the uppermost position. Once both lines are in alignment, do not move the workpiece. Remove the padlock then plug the saw into the power source. Make several practice cuts on different styles and thickness of material. Repeat the steps above as necessary. Follow the directions below for using the laser guide. Removing Your Mark: Position the laser line near the left edge of your mark on the work surface in order to remove the mark. To Cut Your Mark: Position the laser line near or over your mark on the work surface in order to cut the mark. To Leave Your Mark: Position the laser line near the right edge of your mark on the work surface in order to leave the mark. After you have become familiar with using the laser guide, you will be able to remove, cut, or leave your mark on the work surface. Practice will teach you the correct position for aligning the laser line with your mark. NOTE: When finished, turn off the laser guide line to prolong battery life. 17 laser line Fig. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
17
ASSEMBLY
DANGER:
Laser radiation. Avoid direct eye contact with light source.
WARNING:
Use of controls or adjustments or performance of pro-
cedures other than those specified herein can result in
hazardous radiation exposure.
ALIGNING THE LASER GUIDE LINE
See Figures 13 and 14.
Lock out the switch trigger by installing a padlock (not in-
cluded). Draw a line on the workpiece. When the laser guide
switch is turned on it will generate a red line on the work
surface. This line will let you see your mark and the laser
guide line at the same time, and will assist you in lining up
the mark for more accurate cutting of the workpiece.
Align the laser line and the mark with the blade at the up-
permost position. Once both lines are in alignment, do not
move the workpiece.
Remove the padlock then plug the saw into the power source.
Make several practice cuts on different styles and thickness
of material. Repeat the steps above as necessary.
Follow the directions below for using the laser guide.
Removing Your Mark:
Position the laser line near the left edge of your mark on the
work surface in order to remove the mark.
To Cut Your Mark:
Position the laser line near or over your mark on the work
surface in order to cut the mark.
To Leave Your Mark:
Position the laser line near the right edge of your mark on
the work surface in order to leave the mark.
After you have become familiar with using the laser guide,
you will be able to remove, cut, or leave your mark on the
work surface. Practice will teach you the correct position for
aligning the laser line with your mark.
NOTE:
When finished, turn off the laser guide line to prolong
battery life.
Fig. 14
LASER LINE