Samsung DVG45T6000W/A3 User Manual - Page 30

Ducting, requirements, Exhaust ducting guide, Installation check codes, Check code, Meaning, Solution

Get Samsung DVG45T6000W/A3 PDF manuals and user guides View all Samsung DVG45T6000W/A3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Installation Installation NOTE • During or after the test, the internal drum is hot. Use caution to prevent burns. The Vent Blockage Test is used to check for problems in the current duct system when the dryer is installed for the first time. • If the test result displays check code (the duct system is blocked ), refer to the "Ducting requirements" section on page 15 and the "Exhaust ducting guide" section below, and then take proper measures to correct any problems. If the test is suspended, it could result in incorrect results. Follow the proper procedures when testing the dryer. • Even if the test result is normal ("0"), the duct system could be blocked slightly. Properly install all duct work according to the installation instructions in this manual. Installation check codes Check code 0 Clg (Cg) C80 (C8) C90 (C9) Ct tC C1 dC Meaning Solution Vent condition is good. The vent is clogged. About 80 % of the vent is clogged. (This may decrease the drying performance.) Over 90 % of the vent is clogged. (This may lead to poor drying performance or cause malfunction) 1. Clean the lint filter. 2. Check your vent condition. (Refer to the "Ducting requirements" section) * You must take measures (such as cleaning) through expert personnel. The internal temperature of the dryer is too low (below 32 °F (0 °C)) or too high (over 104 °F (40 °C)) and therefore vent blockage cannot be detected. Leave the dryer at room temperature (41~95 °F (5~35 °C)) for an hour and check again. Temperature sensor error. Contact a service center. Unit is detecting items inside the drum or there is an error on the dry sensor. Remove items from the drum and check again. If the problem continues, contact a service center. Unit is detecting door is open. Close the door properly and check again. If the problem continues, contact a service center. 30 English Untitled-10 30 2020-07-14 3:22:16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
Installation
English
30
Installation
NOTE
•
During or after the test, the internal drum is hot. Use caution to prevent burns. The
Vent Blockage Test is used to check for problems in the current duct system when the
dryer is installed for the first time.
•
If the test result displays check code (the duct system is blocked ), refer to the “
Ducting
requirements
” section on page
15
and the “
Exhaust ducting guide
” section below, and
then take proper measures to correct any problems. If the test is suspended, it could
result in incorrect results. Follow the proper procedures when testing the dryer.
•
Even if the test result is normal (“
0
”), the duct system could be blocked slightly.
Properly install all duct work according to the installation instructions in this manual.
Installation check codes
Check code
Meaning
Solution
0
Vent condition is good.
Clg (Cg)
The vent is clogged.
1.
Clean the lint filter.
2.
Check your vent condition.
(Refer to the “
Ducting
requirements
” section)
* You must take measures (such as
cleaning) through expert personnel.
C80 (C8)
About 80 % of the vent is clogged.
(This may decrease the drying
performance.)
C90 (C9)
Over 90 % of the vent is clogged.
(This may lead to poor drying
performance or cause malfunction)
Ct
The internal temperature of the
dryer is too low (below 32 °F (0 °C))
or too high (over 104 °F (40 °C))
and therefore vent blockage cannot
be detected.
Leave the dryer at room
temperature (41~95 °F (5~35 °C))
for an hour and check again.
tC
Temperature sensor error.
Contact a service center.
C1
Unit is detecting items inside the
drum or there is an error on the
dry sensor.
Remove items from the drum and
check again.
If the problem continues, contact a
service center.
dC
Unit is detecting door is open.
Close the door properly and check
again.
If the problem continues, contact a
service center.
Untitled-10
30
2020-07-14
°° 3:22:16