Samsung DVG54R7600V/A3 User Manual - Page 26

Installation, tighten the coupling by hand until it is

Get Samsung DVG54R7600V/A3 PDF manuals and user guides View all Samsung DVG54R7600V/A3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Installation 4. Connect the angled end of the water hose to the filling valve at the bottom of the rear frame. Turn the coupling manually until it is tight. 5. Using pliers, tighten the coupling an additional two-thirds turn. Do not overtighten because the coupling may be damaged. 6. If you detached the cold water hose from your washer, attach the hose to the open end of the Y-connector, tighten the coupling by hand until it is tight, and then, using a pliers, tighten an additional two-thirds turn. 7. Open the cold water tap, and then check for any leaks. If the Y-connector cannot be directly connected to the cold water tap, use the short hose. See the "Using the short hose as an extension" section on page 27. Installation 26 English Untitled-18 26 2020-07-14 3:40:07

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Installation
English
26
Installation
4.
Connect the angled end of the water
hose to the filling valve at the bottom
of the rear frame. Turn the coupling
manually until it is tight.
5.
Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten because the coupling may
be damaged.
6.
If you detached the cold water hose
from your washer, attach the hose
to the open end of the Y-connector,
tighten the coupling by hand until it is
tight, and then, using a pliers, tighten
an additional two-thirds turn.
7.
Open the cold water tap, and then check
for any leaks.
If the Y-connector cannot be directly connected to the cold water tap, use the short hose.
See the “
Using the short hose as an extension
” section on page
27
.
Untitled-18
26
2020-07-14
°° 3:40:07