Samsung HW-K550 User Manual - Page 19

Connecting The Surround Speakers, Sold Separately, Connections

Get Samsung HW-K550 PDF manuals and user guides View all Samsung HW-K550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

ENG CONNECTIONS If the Wireless Receiver Module is not linked to your Soundbar (displaying the LED indicator in Red), connect them as follows. 1. Turn off your Soundbar. 2. Press the (Mute) button on your remote control for 5~6 seconds until the ID SET message appears on your Soundbar display. 3. Check the Wireless Receiver Module is in Standby status (displaying the LED indicator in Red). 4. Press the ID SET button on the back with a sharp pin for 5~6 seconds until the LINK LED indicator on the Wireless Receiver Module blinks (in Blue). 5. Turn on your Soundbar with the button on your remote control and wait for a while. They are completely connected to each other if you can see the LINK LED indicator is continuously lit (in Blue). CONNECTING THE SURROUND SPEAKERS (SOLD SEPARATELY) LR SURROUND SPEAKERS OUT SPEAKER IMPEDANCE : 3Ω ID SET Surround Speaker (L) Surround Speaker (R) Wireless Receiver Module ●● Place these speakers to the side of your listening position. If there isn't enough room, place these speakers so they face each other. Position them about 2 to 3 feet above your ear, facing slightly downward. ●● Use the speaker cable to connect the Wireless Receiver Module to the Surround Speakers. ●● Each speaker has a colored label on its back or underside. Each cable has a single colored band near its end. Match the band on each cable to the speaker label by color, and then connect the cable to the speaker. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
ENG
19
CONNECTIONS
If the Wireless Receiver Module is not linked to your Soundbar (displaying the LED indicator in Red),
connect them as follows.
1.
Turn off your Soundbar.
2.
Press the
(Mute) button on your remote control for 5~6 seconds until the ID SET message appears on your
Soundbar display.
3.
Check the Wireless Receiver Module is in Standby status (displaying the LED indicator in Red).
4.
Press the
ID SET
button on the back with a sharp pin for 5~6 seconds until the LINK LED indicator on the
Wireless Receiver Module blinks (in Blue).
5.
Turn on your Soundbar with the
button on your remote control and wait for a while. They are completely
connected to each other if you can see the LINK LED indicator is continuously lit (in Blue).
CONNECTING THE SURROUND SPEAKERS
(SOLD SEPARATELY)
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
ID SET
L
R
Surround Speaker (L)
Surround Speaker (R)
Wireless Receiver Module
●
Place these speakers to the side of your listening position. If there isn't enough room, place these
speakers so they face each other. Position them about 2 to 3 feet above your ear, facing slightly
downward.
●
Use the speaker cable to connect the Wireless Receiver Module to the Surround Speakers.
●
Each speaker has a colored label on its back or underside. Each cable has a single colored band near its
end. Match the band on each cable to the speaker label by color, and then connect the cable to the
speaker.